Author Topic: Resistors from OpAmp Electronics...  (Read 1755 times)

Offline Mythtron

  • ½ Pint
  • *
  • Posts: 32
  • Post quality +0/-0
  • Gender: Male
  • .::Mythtron::.
Resistors from OpAmp Electronics...
« on: March 29, 2008, 11:10:43 AM »
Hello

I am about to purchase some resistors from this website called OpAmp Electronics. I'm not really worried about the quality, just wanting some input for my resistors.

191K -
http://www.opamp-electronics.com/catalog/191k-ohm-14w-metal-film-resistor-pack-100-p-806.html

30K -
http://www.opamp-electronics.com/catalog/294k-ohm-14w-metal-film-resistor-pack-100-p-617.html

10ohm -
http://www.opamp-electronics.com/catalog/ohm-14w-metal-film-resistor-pack-100-p-1041.html

BTW: I am planning on doing a led sound mod.

Thanks

Offline sprocketme2

  • Motor Mouth
  • *
  • Posts: 99
  • Post quality +0/-0
Re: Resistors from OpAmp Electronics...
« Reply #1 on: March 29, 2008, 11:25:42 AM »
I just purchased resistors from there and am still awaiting shipment. Very good store and appears reliable. Also I ordered 191k 1/8W resistors for cheaper, though I dont if they work for this mod.

Note, you wont need 10ohm resistor for the sound reactive mod.
My flickr profile: http://www.flickr.com/photos/47542734@N06/
Contains all my photos for public viewing

Offline Mythtron

  • ½ Pint
  • *
  • Posts: 32
  • Post quality +0/-0
  • Gender: Male
  • .::Mythtron::.
Re: Resistors from OpAmp Electronics...
« Reply #2 on: March 29, 2008, 03:06:02 PM »
Yea, it is a good store...really I just wanted to know if those parts would work for the mod I'm doing. (I'm not sure about the 1/4W and +/-1% tolerance parts :dntknw: )

To give you a better idea of exactly what sort of mod I'm planning to do, here's a schematic:

BTW: Yes, I do plan on using a single LM386 for both the rear speaker and the led's...that won't be a problem will it?

Thank-You,
Mythtron

Offline Mythtron

  • ½ Pint
  • *
  • Posts: 32
  • Post quality +0/-0
  • Gender: Male
  • .::Mythtron::.
Re: Resistors from OpAmp Electronics...
« Reply #3 on: March 29, 2008, 03:08:00 PM »
Oh and the 10ohm resistor...I'll be using it for the trigger activated led's....not the sound mod led's (which will be at other places :cool: ...)

EDIT: Is the above showing correct parallel wiring of the LED's?...cause I'm not a 100% on that... :faint: )
« Last Edit: March 29, 2008, 03:10:45 PM by Mythtron »

Offline SYSTEM aka (Cyberpyrot)

  • Site Founder
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 4091
  • Post quality +3/-0
  • Gender: Male
Re: Resistors from OpAmp Electronics...
« Reply #4 on: March 29, 2008, 04:18:01 PM »
Yea, it is a good store...really I just wanted to know if those parts would work for the mod I'm doing. (I'm not sure about the 1/4W and +/-1% tolerance parts :dntknw: )

To give you a better idea of exactly what sort of mod I'm planning to do, here's a schematic:

BTW: Yes, I do plan on using a single LM386 for both the rear speaker and the led's...that won't be a problem will it?

Thank-You,
Mythtron

Very impresive...

Offline Mythtron

  • ½ Pint
  • *
  • Posts: 32
  • Post quality +0/-0
  • Gender: Male
  • .::Mythtron::.
Re: Resistors from OpAmp Electronics...
« Reply #5 on: March 29, 2008, 07:12:28 PM »
Thanks :x: ...I guess it means alot coming from you. But also, can you tell me if the 1/4W and +/-1% tolerance will affect anything in my situation? For example, if I used a 10ohm for say....5 blue leds...?

Offline sprocketme2

  • Motor Mouth
  • *
  • Posts: 99
  • Post quality +0/-0
Re: Resistors from OpAmp Electronics...
« Reply #6 on: March 29, 2008, 08:51:24 PM »
OK I checked the sound mod tutorial and it shows 1/8W resistors like these from OpAmp: So 1/4W resistors will be fine. And again tolerance is not important.

How did you make that schematic? Its very well done.
My flickr profile: http://www.flickr.com/photos/47542734@N06/
Contains all my photos for public viewing

Offline Mythtron

  • ½ Pint
  • *
  • Posts: 32
  • Post quality +0/-0
  • Gender: Male
  • .::Mythtron::.
Re: Resistors from OpAmp Electronics...
« Reply #7 on: March 30, 2008, 01:51:32 AM »
This is wonderful...now I know that my resistor's are fine! :victory: Thanks sprocketme2!
Quote
How did you make that schematic? Its very well done.
Thanks, I did it in Photoshop...with simple shapes such as squares, rectangles, and circles...and some layer effects. I think that if your pictures are clear and easy to understand, people will be better able to help.

PS: The speaker and the led's going to the same LM386 won't be a problem will it? (ie dimmer leds or softer speaker?)
« Last Edit: March 30, 2008, 01:56:56 AM by Mythtron »

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal