« previous next »
Pages: [1]   Go Down

Author Topic: CLean drill holes  (Read 3786 times)

Offline pmcgrorey

  • Chief squatting Hard
  • *
  • Posts: 21
  • Post quality +0/-0
CLean drill holes
« on: October 18, 2008, 09:39:41 AM »
how do you guys get such clean holes when driling mine leaves a huge lip
Logged

Offline kink192

  • Acid Modder
  • *
  • Posts: 916
  • Post quality +1/-0
  • Gender: Male
Re: CLean drill holes
« Reply #1 on: October 18, 2008, 11:13:04 AM »
drill from both sides. take needle nose pliers and carefully tear it off, or burn/melt it.
Logged
It's been a long time

Offline pmcgrorey

  • Chief squatting Hard
  • *
  • Posts: 21
  • Post quality +0/-0
Re: CLean drill holes
« Reply #2 on: October 18, 2008, 11:44:21 AM »
thanks
Logged

Offline SYSTEM aka (Cyberpyrot)

  • Site Founder
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 4091
  • Post quality +3/-0
  • Gender: Male
Re: CLean drill holes
« Reply #3 on: October 18, 2008, 11:46:05 AM »
I use a powerful laser I call "Preperation H"
Logged

Offline SN!P3R

  • Millennium Poster
  • *
  • Posts: 1444
  • Post quality +0/-10
  • Gender: Male
Re: CLean drill holes
« Reply #4 on: October 18, 2008, 12:25:58 PM »
Quote from: SYSTEM on October 18, 2008, 11:46:05 AM
I use a powerful laser I call "Preperation H"


lol.

i use a dremel drill half way, flip over, drill from the other side.
Logged
BEST 360 MODDING
HELP OUR ECONOMY!

360 MASHUP THREAD

Offline gameroms

  • Granny Spanker
  • *
  • Posts: 376
  • Post quality +3/-0
Re: CLean drill holes
« Reply #5 on: October 18, 2008, 01:13:41 PM »
its called "skill", lol.

i use a hobby knife to trim if it has a lip.
Logged

Offline Winterz117

  • Granny Spanker
  • *
  • Posts: 415
  • Post quality +0/-0
  • Gender: Male
Re: CLean drill holes
« Reply #6 on: October 18, 2008, 03:12:58 PM »
i just use my dremel and drill it from teh outside in and clean it with a razor
Logged

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: CLean drill holes
« Reply #7 on: October 19, 2008, 01:25:25 AM »
Hobby knife, dremel, drill press.
Logged

Sigs by Alien_X
www.ax-elec.com

Offline pmcgrorey

  • Chief squatting Hard
  • *
  • Posts: 21
  • Post quality +0/-0
Re: CLean drill holes
« Reply #8 on: October 19, 2008, 12:09:29 PM »
Quote from: kink192 on October 18, 2008, 11:13:04 AM
drill from both sides. take needle nose pliers and carefully tear it off, or burn/melt it.
thanks mine came out perfect
Logged

Offline Containm3nt

  • Chief squatting Hard
  • *
  • Posts: 24
  • Post quality +0/-0
  • Gender: Male
  • [ACID]Containm3nt
Re: CLean drill holes
« Reply #9 on: October 19, 2008, 01:48:03 PM »
De Walt Cordless, stepping up the size 2 or 3 times till I get the right size hole, then the X-acto knife. Also start on the outside going in and clean the inside edge.
Logged

Offline 802Chives

  • Sargeant at Arms
  • Acidmods Alumni
  • Millennium Poster
  • *
  • Posts: 1304
  • Post quality +10/-0
  • Gender: Male
Re: CLean drill holes
« Reply #10 on: October 19, 2008, 04:47:07 PM »
Quote from: Containm3nt on October 19, 2008, 01:48:03 PM
De Walt Cordless, stepping up the size 2 or 3 times till I get the right size hole, then the X-acto knife. Also start on the outside going in and clean the inside edge.

Pre-drill with smaller bit first from inside, then use the required bit from outside. Buff up with Xacto Knife. Like ^he^ said
Logged

Offline Containm3nt

  • Chief squatting Hard
  • *
  • Posts: 24
  • Post quality +0/-0
  • Gender: Male
  • [ACID]Containm3nt
Re: CLean drill holes
« Reply #11 on: October 19, 2008, 07:28:25 PM »
To keep the bit from walking, I take something with a very fine hard point and make a small divot or mark where i want the bit to drill through, then begin with the smaller bit. I learned that little lesson the hard way... :angry:
Logged

Offline Winterz117

  • Granny Spanker
  • *
  • Posts: 415
  • Post quality +0/-0
  • Gender: Male
Re: CLean drill holes
« Reply #12 on: October 20, 2008, 11:52:52 AM »
yeah me to haha
Logged

Offline KingMike_OS

  • Shop Owner - Products & Support
  • Acidmods Alumni
  • Acid Modder
  • *
  • Posts: 929
  • Post quality +14/-0
  • Gender: Male
  • R&D
    • Modding Shop At the end of the Universe
Re: CLean drill holes
« Reply #13 on: October 23, 2008, 12:02:05 AM »
I don't even use a drill ..

I use a high Power Green Lazer  :#1:
Logged

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: CLean drill holes
« Reply #14 on: October 23, 2008, 02:25:01 AM »
Quote from: KingMike_OS on October 23, 2008, 12:02:05 AM
I don't even use a drill ..

I use a high Power Green Lazer  :#1:

If you are joking, then  :nono:

Otherwise, awesome!
Logged

Sigs by Alien_X
www.ax-elec.com

Offline bill16504

  • King of the Wii-tards
  • *
  • Posts: 163
  • Post quality +0/-0
  • Gender: Male
Re: CLean drill holes
« Reply #15 on: October 23, 2008, 01:49:40 PM »
Wow. A bunch of you guys do it the hard way. I drill my holes to size on a drill press then clean up the lip and put a slight chamfer on by gently twisting a phillips head screwdriver in the hole. Works beautiful.
Logged

Offline Winterz117

  • Granny Spanker
  • *
  • Posts: 415
  • Post quality +0/-0
  • Gender: Male
Re: CLean drill holes
« Reply #16 on: October 24, 2008, 04:13:29 AM »
oh never thought of putting a chamfer on thats a great idea!
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal