Author Topic: need a power source in a 360 wireless controller  (Read 2585 times)

Offline RiP

  • Chief squatting Hard
  • *
  • Posts: 27
  • Post quality +0/-0
  • Gender: Male
  • Gasoline in my veins, electricity in my brain
need a power source in a 360 wireless controller
« on: September 06, 2009, 09:37:46 AM »
i need a permanent power source in a 360 wireless controller turned on when the controller is on... off when it is off...

picture would be great^^

thanks

Offline Ben.

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 657
  • Post quality +2/-0
  • Gender: Male
Re: need a power source in a 360 wireless controller
« Reply #1 on: September 06, 2009, 10:11:57 AM »
I'm pretty sure there isn't a standby power source unless you use a transistor?

correct me if I'm wrong.

Offline RiP

  • Chief squatting Hard
  • *
  • Posts: 27
  • Post quality +0/-0
  • Gender: Male
  • Gasoline in my veins, electricity in my brain
Re: need a power source in a 360 wireless controller
« Reply #2 on: September 07, 2009, 09:20:25 AM »
Ok, so how to built on, with à transisor if nessesary...

Offline blackburn

  • Acid Modder
  • *
  • Posts: 915
  • Post quality +0/-0
  • Gender: Male
  • Xbox 360 Enthusiast and JTAGer
Re: need a power source in a 360 wireless controller
« Reply #3 on: September 07, 2009, 11:32:39 AM »
matrix or CG?


All Sigs Made by ME!

Offline RiP

  • Chief squatting Hard
  • *
  • Posts: 27
  • Post quality +0/-0
  • Gender: Male
  • Gasoline in my veins, electricity in my brain
Re: need a power source in a 360 wireless controller
« Reply #4 on: September 10, 2009, 06:23:00 AM »
matrix^^

Offline blackburn

  • Acid Modder
  • *
  • Posts: 915
  • Post quality +0/-0
  • Gender: Male
  • Xbox 360 Enthusiast and JTAGer
Re: need a power source in a 360 wireless controller
« Reply #5 on: November 01, 2009, 08:13:07 PM »
theres 3 holes next to the left vibrator plug, far left hole is V+


All Sigs Made by ME!

Offline Amerikun Soljia

  • Ω Allumnist Ω
  • *
  • Posts: 129
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: need a power source in a 360 wireless controller
« Reply #6 on: November 03, 2009, 03:57:50 PM »
What is v+? as far as a permanent power source, do you mean you want to have a controller that never runs out of juice? or for Led's? I wonder if its at all possible to make a controller permanently have power, o more duracell's? Oh, yeah!! What about adding a battery for Led's, like one of those round batteries you find in a car stereo remote? Can it be done? Sorry if I am asking in the wrong thread, But I figured, power source in a 360 controller would be the right place to ask.


y nomeni patri et fili, y spiritu sancti.

Offline lilunwl

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 61
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: need a power source in a 360 wireless controller
« Reply #7 on: November 04, 2009, 05:50:06 AM »
Ok here is what I can tell you because I recently went through this problem as well. With the matrix controller I only found a 2 volt output with a switched power point. Meaning it will turn on and off with the controller being turned on or off. Below the left trigger pot are 3 holes. The far left is a switched power but is only a 2 volt output on a matrix. CG board has 3 volt switched power points but as far as I know the matrix does not. If you tell us what your trying to acheive maybe we can help a little more. I am assuming your wanting to do some led work but I will let you tell us.

Amerikun Soljia Yes you can add a coin cell battery to get more power if you want but then I believe you will also need to put an on and off switch in to. Your coin cell batteries need to have solder tabs on them  or you have to clean the battery with phosphoric acid. and then you can solder to the battery. I use naval jelly. Its phosphoric based.  However I MUST SAY IF YOUR SOLDERING BATTERIES MAKE SURE YOUR EXPERIENCED TO DO IT BECAUSE THEY CAN AND WILL EXPLODE WITH TO MUCH HEAT!!!!

Offline Amerikun Soljia

  • Ω Allumnist Ω
  • *
  • Posts: 129
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: need a power source in a 360 wireless controller
« Reply #8 on: November 04, 2009, 11:54:12 AM »
Yes, I am trying to do leds that I can turn on and off when I wish, not just when the controller is on they stay on. some days you don't want all that light, ya know? so I want to install a switch and battery.


y nomeni patri et fili, y spiritu sancti.

Offline 802Chives

  • Sargeant at Arms
  • Acidmods Alumni
  • Millennium Poster
  • *
  • Posts: 1304
  • Post quality +10/-0
  • Gender: Male
Re: need a power source in a 360 wireless controller
« Reply #9 on: November 05, 2009, 09:02:40 AM »
on a matrix controller the normal 3V source that most people use, is battery voltage when the controlller is off and 3V when it is on.  The 2V source that lilunwl suggestted will also work but limits you pretty much to red LEDs.

A common solution that people who want 3V from there matrix that is switched is to use a NPN transistor whose base hooks up through a 1.5k resistor to the 2V spot.  the Emitter hooks up to ground and the collector hooks up to the ground of the circuit you are installing.  what this does is breaks the ground connection when the controller is off which will disable your circuit even tho positive connection of your installed circuit is connected to the live 3V spot.

CG does not have this problem the 3V spot is switched off when controller is not on.
« Last Edit: November 05, 2009, 09:04:40 AM by 802Chives »


 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal