Author Topic: Is this a correct led diagram for trigger mod?  (Read 10131 times)

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: Is this a correct led diagram for trigger mod?
« Reply #30 on: July 05, 2009, 06:14:33 PM »
"a 2000 mcd 30° LED puts out just as much light as am 8000 mcd LED with a 15° viewing angle. (The angle is half in both width and height, so the beam is four times as bright.) This is one of the reasons that ultra-bright LEDs are often "water clear", to keep the light going in one direction and not diffuse it all over the place. "

-http://www.gizmology.net/LEDs.htm



Yes jumbo is right, sorry.  :#1:

Sig by Kenshinffx - Thanks!

Offline ojomow

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 50
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Is this a correct led diagram for trigger mod?
« Reply #31 on: July 05, 2009, 06:18:13 PM »
Really? The diagram doesn't say.. that a bummer.

So that would be on the wire of pin 4 right? or the ground wire.

Offline RoBot1ks

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 671
  • Post quality +0/-0
  • Gender: Male
  • 1 r n00ber
    • Myspace
Re: Is this a correct led diagram for trigger mod?
« Reply #32 on: July 05, 2009, 06:32:12 PM »
"a 2000 mcd 30° LED puts out just as much light as am 8000 mcd LED with a 15° viewing angle. (The angle is half in both width and height, so the beam is four times as bright.) This is one of the reasons that ultra-bright LEDs are often "water clear", to keep the light going in one direction and not diffuse it all over the place. "

-http://www.gizmology.net/LEDs.htm



Yes jumbo is right, sorry.  :#1:
Well then I'm sorry for reading the friggin spec sheet
Wouldn't it be common sense to put a legit mcd rating on a product? WOW

Offline ojomow

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 50
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Is this a correct led diagram for trigger mod?
« Reply #33 on: July 05, 2009, 06:48:27 PM »
Alright someone clarify how many resistors are needed for the LM386?

is it 3? and where does the 10 ohm goes onto pin4 then solder to wire?

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: Is this a correct led diagram for trigger mod?
« Reply #34 on: July 05, 2009, 06:56:01 PM »


10ohm can go either on the + or - pins of the leds.

Sig by Kenshinffx - Thanks!

Offline ojomow

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 50
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Is this a correct led diagram for trigger mod?
« Reply #35 on: July 05, 2009, 06:59:41 PM »
That the slim diagram, mines the phat.

So can you tell me if can solder the 10ohm directly onto the pin4 (ground) and then connect  it to the wire and that leads to the LED negative?

Offline Blazinkaos

  • Technology Revolution
  • Art & Theme Team
  • E = MC² Mad Scientist
  • *
  • Posts: 2259
  • Post quality +12/-0
  • Gender: Male
  • Time Passes Will You
    • ROOKIE BUILDERS DISCORD
Re: Is this a correct led diagram for trigger mod?
« Reply #36 on: July 05, 2009, 08:00:52 PM »
Yea but its the same concept except the phat has different points is all.

*Thanks Modders/Friends:Ghost_Death, gr8npwrfl, Blizzrad, Kenshinffx.
*Thanks 802Chives for the Art position!

Offline ojomow

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 50
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Is this a correct led diagram for trigger mod?
« Reply #37 on: July 05, 2009, 08:17:33 PM »
I have the Phat layout printed.

You said I need a 10 ohm onto the negative lead right?
So do I put that 10 ohm onto the pin4 then solder to wire then negative led side?

like   [PIN4]-~~10.OHM~~-wire->negative contact 0603

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: Is this a correct led diagram for trigger mod?
« Reply #38 on: July 05, 2009, 09:48:24 PM »
Yep :) Sorry forgot you were doing a phat... Here's the diagram:


Sig by Kenshinffx - Thanks!

Offline RoBot1ks

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 671
  • Post quality +0/-0
  • Gender: Male
  • 1 r n00ber
    • Myspace
Re: Is this a correct led diagram for trigger mod?
« Reply #39 on: July 06, 2009, 07:01:31 AM »
Good luck with your mod dude.
But don't use the points from the motherboard. Use them from the speaker itself. So much easier

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: Is this a correct led diagram for trigger mod?
« Reply #40 on: July 07, 2009, 07:42:22 AM »
Dude nobody is answering is :censored:ing question. Have we forgotten to read?

No you connect the 10 ohm resistor to the Positive side of the LEDs.

Resistors resist the amount of volts going to the leds, thats why they last longer.

If you need anything else just PM me it seems everyone else cares about arguing about MCD.

Also heres a quick picture:

 :drunk:
« Last Edit: July 07, 2009, 07:45:35 AM by Jumbo »

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: Is this a correct led diagram for trigger mod?
« Reply #41 on: July 07, 2009, 08:05:36 AM »
I thought the resistor can go anywhere as long as it's in the same circuit and in series with the leds.

Sig by Kenshinffx - Thanks!

Offline ojomow

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 50
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Is this a correct led diagram for trigger mod?
« Reply #42 on: July 07, 2009, 08:11:26 AM »
Thanks Jumbo, now I know where all the stuff goes now. All maters is shipping.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal