Author Topic: ROBBO 2011 new code 3 mode jitter fully adjustable (black ops tested (Read 22134 times)

Famas · « **on:** January 13, 2011, 03:52:33 PM »

Hello acidmods im posting this on behalf of robbo3 this is his new code for 2011 theres 2 things this does its the same install as all his other jitter codes heres a picture cg only here is a video of the code in action theres 1 thing i want from you 1 bug reporting etc
any problems contact me this is robbo wish people id like to thank

robbo for making this fine code
frenulem for the acidmods video intro
and last but not least hyper999 for his intrest and encouragement
thanks guy

robbo 3 mode jitter code acidmods.com

modes are
1 jitter (adjustable)
2 dual wield (adjustable)
and 3 standard rapid fire (adjustable)

once controller is powered up is lt and sync to turn on and then to adjust fire rate select mode desered to alter them pres rt + sync you are now in programming mode 1 press on the right trigger is + 1 sps and 1 left is -1 sps the sync button is 0.1 sps once you increment the 0.1 to 0.9 + it goes back to 0 once controller is powered on and you have pressed lt+ sync to change mode it is just 1 tap of the sync button thankyou

EasyE · « **Reply #1 on:** January 14, 2011, 02:55:35 AM »

Nice Robbos codes are always so much fun

Famas · « **Reply #2 on:** January 14, 2011, 03:41:51 AM »

yea i no good look fitting it

lovey · « **Reply #3 on:** January 14, 2011, 07:33:22 AM »

nice work its working very well thanks famas for posting it and a big thanks for robbo for making it.

Famas · « **Reply #4 on:** January 14, 2011, 07:40:46 AM »

no probs lovey enjoy it dude it great for black ops post speed result for everyone else please

Anonamous · « **Reply #5 on:** January 14, 2011, 10:31:49 AM »

What were the speeds used in the video? I want to know the speed used for the jitter mode

Famas · « **Reply #6 on:** January 14, 2011, 10:35:19 AM »

let me check 1 min just jitter or the fal speed aswell

Anonamous · « **Reply #7 on:** January 14, 2011, 10:38:43 AM »

Quote from: Famas on January 14, 2011, 10:35:19 AM

let me check 1 min just jitter or the fal speed aswell

I always used 8.9sps for the fal but the one in the video was obviously much faster than that lol. Ill take all the speeds used in the video please

Famas · « **Reply #8 on:** January 14, 2011, 10:57:34 AM »

mode 1 10 main flashes 0 fast flashes
mode 2 8 main flashes 6-7 fast flashes
mode 3 21 main flashes 2 fast flashes
good luck post result please

Anonamous · « **Reply #9 on:** January 14, 2011, 11:18:49 AM »

Quote from: Famas on January 14, 2011, 10:57:34 AM

mode 1 10 main flashes 0 fast flashes
mode 2 8 main flashes 6-7 fast flashes
mode 3 21 main flashes 2 fast flashes
good luck post result please

ok will do. itll have to wait untill later saturday though cause i got work

Famas · « **Reply #10 on:** January 15, 2011, 05:37:50 AM »

just wondering how you got on

Anonamous · « **Reply #11 on:** January 15, 2011, 02:12:02 PM »

Quote from: Famas on January 15, 2011, 05:37:50 AM

just wondering how you got on

??? what?

I put the settings to what you said they were in the video and got results nothings close to the video.

Famas · « **Reply #12 on:** January 15, 2011, 02:38:56 PM »

so what did you try it with fal was with rapid fire and this pistols where with jitter and dual akimbo mode

Anonamous · « **Reply #13 on:** January 15, 2011, 04:58:20 PM »

Quote from: Famas on January 15, 2011, 02:38:56 PM

so what did you try it with fal was with rapid fire and this pistols where with jitter and dual akimbo mode

well the akimbo and regular were closer to the video than the jitter. the jitter still seems way off. it gets off the first 3 shots than everytime it swithces it gets off 1 shot and swithces weapons again.

deek · « **Reply #14 on:** January 18, 2011, 04:08:41 AM »

Quote from: Anonamous on January 15, 2011, 02:12:02 PM

??? what?

I put the settings to what you said they were in the video and got results nothings close to the video.

I fitted this RF to a controller yesterday and tried it out with the settings Famas posted earlier... I'd say with my controller it works, as near as I can tell, identically to how it does in the vid

This is the first time I've tried out a 'jitter mod'. I have to agree with others who've said it, that for me it's more of a 'LOL at that!', novelty mod than anything else.

Huge thanks to Robbo for developing (and sharing!) the code, also to Famas for his involvement

Famas · « **Reply #15 on:** January 18, 2011, 04:13:43 AM »

hello deek and welcome to acidmods im just wondering if you could do a little more adjusting on blackops and find the best speed for the fal please or is my settting ok ?

deek · « **Reply #16 on:** January 18, 2011, 05:25:45 AM »

Hi and thanks

Yeah sure I'll have a play around this evening after work and report back..

Post Merge: January 19, 2011, 05:13:05 AM

I can confirm, for me, your settings of 8.6/ 8.7 for the FAL work the best.. I use 8.7 for the FAL with FLEX rf too, iirc the shot cap for the FAL is at 9sps. I did run FLEX at 8.9 for a while but would still get the occasional lock up, so I knocked it back a couple as I'd far rather have reliability than the extra .2sps

Btw have you guys seen this gun stats chart?
http://denkirson.proboards.com/index.cgi?board=general&action=display&thread=2097

The info on it is extracted from the pc version game files. It has firetime and rounds per minute info for all the guns.

falo21 · « **Reply #17 on:** January 19, 2011, 02:32:35 PM »

this is my first jitter so im loving and it was really easy to installed.great job ROBBO

phil789 · « **Reply #18 on:** January 23, 2011, 03:18:04 PM »

does anyone know were i can get the other controller picture from... many thanks...

Famas · « **Reply #19 on:** January 23, 2011, 03:19:45 PM »

hi this code is only made for a cg pad sorry someone found a way to make it work for matrix but i dont no how sorry my friend

phil789 · « **Reply #20 on:** January 23, 2011, 03:32:12 PM »

thanks for the reply! if you find a way let me know...

Famas · « **Reply #21 on:** January 23, 2011, 03:33:56 PM »

if you have a matrix pad let me suggest putting a different rapid fire setup in like flex maybe

gadget78 · « **Reply #22 on:** January 23, 2011, 03:54:01 PM »

thought i would add this diagram that i just used/made for the CG2 controllers
as the details were not all in the same place !!
it includes the opto coupler, and all the points are on the top which made it much easier to install test etc ..
you can use either side LED of course, and either side trigger for the power/earth for opto

hope it helps some1

Also added the matrix diagram that i made/used too as people dont seem to be able to search or find my other posts about it !

Famas · « **Reply #23 on:** January 23, 2011, 04:10:48 PM »

hey thanks dude that really really helped pm me the pics and ill put it in the main post really thanks alot

EasyE · « **Reply #24 on:** January 24, 2011, 04:44:35 AM »

gadget thanks for posting that but just out of curiosity where is the y solder point for the matrix? The cg2 is under the dpad is the matrix on the back of the board?

hyper999 · « **Reply #25 on:** January 24, 2011, 07:57:41 AM »

you will need extra components for this to work on a matrix pad, better off stickking with CGs

gadget78 · « **Reply #26 on:** January 24, 2011, 10:29:17 AM »

Quote from: EasyE on January 24, 2011, 04:44:35 AM

gadget thanks for posting that but just out of curiosity where is the y solder point for the matrix? The cg2 is under the dpad is the matrix on the back of the board?

do you not understand the diagram i posted for the matrix ? it has both the locations for the Y contact !!
as on the matrix you have to join the two labeled points together (you cannot give the contact(s) a + or a -, they need to be joined, which is why you need a seperate device/componant to do this for you.. hence the extra componant in the diagram !

so thats why its ALOT easyier to use/install jitter mods on CG/CG2 controllers
(i only did it on this matrix, one for the challenge, and two its what i had about, so cost was low

EasyE · « **Reply #27 on:** January 24, 2011, 04:36:21 PM »

got it thanks

lecrack65 · « **Reply #28 on:** January 26, 2011, 03:36:54 PM »

hello to all and foremost thank you for this new mod I wanted to know if mounting above and valid for my CG and CG2
also like to know if the brown wire must be in the hole to weld, or if there is a little scratch for welding wire
thank you for your reply

Famas · « **Reply #29 on:** January 26, 2011, 03:42:20 PM »

hello yes it will work for cg and cg2 but the cg2 y trace will be different to the one in the picture and you dont weld you solder just to be clear if the wire is kynar 30 awg it should be stripped and pushed in the hole that would work fine

lecrack65 · « **Reply #30 on:** January 26, 2011, 03:55:51 PM »

it is possible to create a collage or do not Photocoupler and where he should not to scratch the PCB for cg2?

hyper999 · « **Reply #31 on:** January 27, 2011, 08:01:37 AM »

say what? LOL

Famas · « **Reply #32 on:** January 27, 2011, 09:51:30 AM »

im trying to help here if you want to scratch the pcb buy a fiber glass pen i bought 1 today and they great for jobs like this please dont hesitate to contact me and ill be happy to help you find the y trace on a cg2 if you dont no what we are talking about im sure you could sendyour controller to a modder on this forum to help you out

gadget78 · « **Reply #33 on:** January 27, 2011, 12:11:28 PM »

can you not see the diagrams in my last post they are the CG2 ones lecrack65 !
(Famas maybe confused you by saying what he said ? as the diagram/pic in the first post is for CG, and the one in my post is the one for CG2 (and cannot just poke it into the via on the CG2 as they are filled up)

the diagrams i posted has everything you need for the CG2 ! thats why i posted them !
the opto points, and the Y point !!
and if you are asking how to solder onto the Y point then you should not be attempting it in my opinion !!
(but yes just scrape the protective paint off to see the copper and solder to that its simple common sense)

manwinder · « **Reply #34 on:** January 29, 2011, 10:18:20 PM »

i was wondering what is MC74HC4053A, is that some sort of chip thing i have to get and do i have to program it, and what about the optocoupler, do i have to buy that to and do i have to program it, what do these chips do and could somebody post a link to where i could buy them and is the cg2 the new wireless d-pad controller that microsoft just released, it comes bundled with the slim

Famas · « **Reply #35 on:** January 30, 2011, 04:11:33 AM »

they cg2 was going long before the slim 360 as i have 1 from a year or so ago you will need a transistor for the chip to shut off ive not looked at the pictures but i think you can use n2222 but im not 100 percent and with the opto coupler its just a diode so no need to program it and for the chip you need to program the 12f683 the chip used originally but as for the other chip no i dont think so good luck will look for pics

hyper999 · « **Reply #36 on:** January 30, 2011, 05:06:36 AM »

the MC74HC4053A was used in order to make this work on a matrix board if you are using a CG or CG2 you do not need one

manwinder · « **Reply #37 on:** January 30, 2011, 08:24:29 AM »

i have both types of controllers matrix, cg, and the new 360 d-pad controllerhttp://www.engadget.com/2010/08/31/new-xbox-360-controller-with-improved-d-pad-confirmed-by-major-n/, i am just wondering what do i require for both the controllers, i already have the pic12f683, all the resistors, 1N4148 , i just need to know do i need the other stuff like a optocouplor, is this one good: http://cgi.ebay.ca/20-pcs-SFH620AA-Optocoupler-AC-Input-Optoisolator-/110479348702?pt=LH_DefaultDomain_0&hash=item19b91513de and what about the other chip, MC74HC4053A, where do i get that, is searched ebay and couldn't find any, where can i get some and is the new controller cg3 maybe, it looks like a cg2 but the microsoft logo is placed in a different spot

Post Merge: January 30, 2011, 07:01:42 PM

i was wondering what is the best rapidfire code, and is using a jitter mod harder to install because the pictures look complicated, isn't there a jitter mod where i just install the pic12f683, some resistors and some diodes or does jitter require you to install 74HC4053 chip or a optocouplor

Phantom · « **Reply #38 on:** January 30, 2011, 10:58:37 PM »

if you want to install it on a cg, follow the diagram in the first post, you dont need anything extra.

if you want to install it on a cg2, you will need an optocoupler. the controller with the new dpad has a cg2 board.

if you want to install it on a matrix, you will need that MC74HC4053A thing, which is apparently out of a dvd player, idk anything bout it

the best rapid fire code in my opinion is flex.

manwinder · « **Reply #39 on:** January 31, 2011, 04:01:47 AM »

why do u think flex is the best, what are the difference, Thanks a lot guys for helping me out

Phantom · « **Reply #40 on:** January 31, 2011, 04:47:31 AM »

https://www.acidmods.com/forum/index.php/topic,35802.0.html

Compare them yourself

Famas · « **Reply #41 on:** January 31, 2011, 04:53:00 AM »

well i think this code is the best just because i used it on black ops and it was fine flex is "what you see is what you get" great code but in my opinion hard to learn how to use this code is the only code that will fire the g11 in blackops fully auto if you want it for dual akimbo will do that also and standard rapid fire if you want a break down mate here it is

durability 9/10 (its fully adjustable)
ease of use 9/10 (flex is about a 3 as it took me about a day to figuire out how to use it)
ease of install 9/10 (flex you have to drill a hole but on the other hand no resistors or diodes so hazer i really respect you for doing that mate

so a break down if you want to keep it simple on the soldering etc
use either this code burn me up witch will need editing to work on black ops or crazy modders six mode code please dont hesitate to contact me if any problems arise as im here to help and i no how hard the barrier is between people telling you things you dont quite understand the meaning of so any problems just post in this thread or a pm

manwinder · « **Reply #42 on:** January 31, 2011, 04:57:06 AM »

i want to use the sync button for the rapidfire mode change and not buttons, the pictures for the flex install don't show me this, could i install it like the robbo mod and use flex's code

Famas · « **Reply #43 on:** January 31, 2011, 05:02:59 AM »

simple answer cant be done flex requires a button

Post Merge: January 31, 2011, 05:03:56 AM

read my post before this

manwinder · « **Reply #44 on:** January 31, 2011, 08:26:14 AM »

so what is the best rapidfire mod i can use by tapping the sinc and is easy to install on all controllers

hyper999 · « **Reply #45 on:** January 31, 2011, 08:32:15 AM »

without jitter its probably CrazyModder's six mode
or with jitter its this one

crazy's is not customizable but its very good I've used it myself, it uses the sync button but I couldn't compare it with this as they both fulfil different purposes.

News:

Author Topic: ROBBO 2011 new code 3 mode jitter fully adjustable (black ops tested (Read 22134 times)