Author Topic: Jtag tutorial updated 11/10/12  (Read 50648 times)

Offline Nevbox

  • Granny Spanker
  • *
  • Posts: 356
  • Post quality +12/-5
Re: Jtag tutorial
« Reply #60 on: February 16, 2012, 02:47:04 AM »
The one on this thread + Reverse Jtag wires.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Jtag tutorial
« Reply #61 on: February 25, 2012, 06:12:45 AM »
im doing a falcon this morning

Offline Nevbox

  • Granny Spanker
  • *
  • Posts: 356
  • Post quality +12/-5
Re: Jtag tutorial
« Reply #62 on: February 25, 2012, 09:39:50 AM »
Fixed the errors from earlier, had to remove the resistor on the jtag wires (which stop E80) to be able to w and r.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Jtag tutorial updated 11/10/12
« Reply #63 on: November 11, 2012, 05:58:43 AM »
I have updated the original post to include the files needed for the most current dahsboard. 16179

thanks for the help Rodent

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: Jtag tutorial updated 11/10/12
« Reply #64 on: November 11, 2012, 08:20:29 AM »
I have updated the original post to include the files needed for the most current dahsboard. 16179

thanks for the help Rodent
thanks for updating and your welcome...


 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Jtag tutorial updated 11/10/12
« Reply #65 on: November 13, 2012, 05:02:32 AM »
correct, you have some major issues here. Did you flash the KV and config files back? I am assuming your dump did not have these errors in it.

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: Jtag tutorial updated 11/10/12
« Reply #66 on: November 13, 2012, 09:18:13 AM »
I have a taggable xenon that the solder points are in bad shape,  been seaching all over looking for a way to pic up other points . there are the points that are bad. where the resistors are and where the wires go across from them ... looking for a way to altenate these points to make the the jtag useable. thanks.

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Jtag tutorial updated 11/10/12
« Reply #67 on: November 13, 2012, 09:39:23 AM »
You may be SOL.

I know where the other end of your wires come through on the underside of the mobo, but not the resistor side. I have a zenon at home I can trace out this weekend if you would like. If you find some post them here so I can update the tut, but I dont think you are going to find a picture already posted...

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: Jtag tutorial updated 11/10/12
« Reply #68 on: November 13, 2012, 10:11:06 AM »
thanks . I think it can be done just going to take time and patients to add a wire to the traces, I just want to make sure i get the right traces and make sure i dont tear them or anything.  thanks matt. i been looking havent found any pics or anything yet.

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline 3D0kassiah

  • Acid Modder
  • *
  • Posts: 809
  • Post quality +19/-2
  • Gender: Male
  • Acidmods User
Re: Jtag tutorial updated 11/10/12
« Reply #69 on: November 13, 2012, 10:50:52 AM »


try this method using 2 x switching diodes from j1f1-4 to j2d2-2 and j1f1-3 to j2d2-1 the diodes are 1n4148
and add a 100ohm resistor on j2d2-4 to j2d2-7
if not get out ur multimeter and check the V j2d2-1 and j2d2-2 they should read 1.5k with no power connected
« Last Edit: November 13, 2012, 10:53:33 AM by 3D0 »
Tracey: f off Rodent
rodent:i would of flew it to bill gates and shoved it up his a$$

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Jtag tutorial updated 11/10/12
« Reply #70 on: November 13, 2012, 11:04:47 AM »
the J1F1 points are bad..... he needs to trace them to another point on the mobo.

Offline 3D0kassiah

  • Acid Modder
  • *
  • Posts: 809
  • Post quality +19/-2
  • Gender: Male
  • Acidmods User
Re: Jtag tutorial updated 11/10/12
« Reply #71 on: November 13, 2012, 11:59:03 AM »
oh lol didnt know if it was confirmed that the pads were bad
any evidence of tampering before u got ahold of that console rodent?
and i dont think there is alt points for xenon boards
yeah the only thing i can think of is try to make a connection before the pads by scratching the traces
Tracey: f off Rodent
rodent:i would of flew it to bill gates and shoved it up his a$$

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: Jtag tutorial updated 11/10/12
« Reply #72 on: November 13, 2012, 01:00:55 PM »
yes it was tappared with and the J1f1  area in pretty bad shape and the j2d2 pads the traces are gone around some of the points so hopefully i can get time to sit down and follow the traces and get this thing jtagged... I just asked cause i been looking for 3 days now and think i looked at everything twice maybe 3 times over again.


Thanks for all your help guys. hope together we can get this working :)


 November 14,2012 Edit: if i have to I will totally rebuild the trace i have another xenon here that i can see the traces good, and i will try to rebuild each trace ... If you guys think that is impossible tell me know before i pull my hair out....lol

November 16, 2012 Edit: well i been up since 4am this morning now 3 1/2 hours later I checked everything twice seems like i got all good connections, hard wired the 3 bad traces everything seemed to be going good , dumped the Nand , Flashed xell and Still E-79... removed the resistors and the wires again. only thing i guess i try now instead of Jtaging the xbox i update it, dump the nand again after i Rgh it to get the key and make this a flashed console instead. looks like its the only hope to save another xbox from the junk pile.
« Last Edit: November 16, 2012, 04:29:07 AM by Rodent »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: Jtag tutorial updated 11/10/12
« Reply #73 on: April 28, 2013, 07:43:07 AM »
 Consoles after this date can not be Jtagged  if on 7371  due to they added a patch so it can not be jtagged

June 17th 2009

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Nevbox

  • Granny Spanker
  • *
  • Posts: 356
  • Post quality +12/-5
Re: Jtag tutorial updated 11/10/12
« Reply #74 on: September 30, 2013, 01:15:59 PM »
Made a tutorial last year for how to do this with a LPT PCI expansion card.

https://www.youtube.com/watch?v=lOMGtsmgtZ4
« Last Edit: September 30, 2013, 01:17:43 PM by Nevbox »

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal