Console Modding------ ( Here you can talk about your favorite Consoles ) > Tutorials
Reset Glitch Hack RGH
Rodent:
Reset Glitch Hack RGH
Acidmods and Myself are Not Responsible for Damages done to your console***NOTE: READ!! The whole post and replys. ***
***Updates applied for future updates***
Introduction
This will tell you everything there is to know about The RGH Reset Glitch Hack and what is needed For every console out there. I can not say it any more clearer then to Read this carefully and ask questions if needed before you do anything. You must have good soldering skills and you must pay attention to everything you do. This tutorial will teach you everything you need to RGH a xbox 360 console and the tools you will need for each type of console and what you will need for each dashboard.
Parts Needed
* J-Runner Program (http://www.ixtreme.net/jtag-rgh/25690-j-runner-ultimate-jtag-rgh-app-download.html)
* Coolrunner Rev A,B,C,
* Matrix Glitcher Chip (this can be used instead of cool runner)
* Xbox 360 Motherboard (xenon) not good for RGH at this time (Zephyr, Falcon, Jasper SB/BB, Trinity or Corona)
* Corona Varies on parts you need qsb micro card reader so please Research for your type of Corona Motherboard
Tools Needed
* 15 Watt Soldering Iron
* Flux paste
* Solder
* Nand X or jr programmer or USB Nand Reader or LPT [smg id=2917]
* jr Programmer[smg id=2918]
* Nand X to Coolrunenr Jtag Cable[smg id=2916]
* DGX ( use only on dashboards 15574 to 16202 and above) This is used to get the cpu key from them Dashboard Kernals)" Slim Consoles only at this time [smg id=2919]
* For Corona boards and to update jr.programmer or nand x USB to NAND-X Update Cable/ Comm v3[smg id=2920]
Difficulty rating: 5/5
Average Time to Complete: 45mins to 1 1/2 hours
Notes:
What makes it difficult : small soldering , must have good soldering skills , small points, easy to bridge or remove small components if your not careful very easy to lift traces . I can not say it enough please becareful when soldering.
* 8955 to 14699 RGH 1
* 14717 to 17150 RGH 2
* Slim Trinitys Wired like RGH2
* Slim Coronas Best to check Version first
Step By Step Tutorial
1- Check to make sure the Xbox 360 has no issues such as damage to the console or Motherboard , checking to make sure no one else has tried to rgh the console. Or making sure that it powers on and boots up normally.
2- Check to see what dashboard it is on by going to Console Settings, System Info This will tell you what type of RGH can be done ont the console. "NOTE" If it is a jasper you need to make sure what size it is 16mb , 256mb, 512mb,
3- Power off the console. Once turned off unplug it and carefully removing the dvd drive , fan shroud and the mother board from the cage.
4- After you figured out what RGH Version you have. you can now go ahead and program the coolrunner to the type of board you have. If it is RGH2 you need to make sure that is marked in J-runner RGH2 there are different settings for RGH2 when programming the coolrunner. and If its a jasper you need to make sure you check its 16mb , 256mb or 512mb
"NOTE" Coolrunner must be on phat for phat and slim for slim consoles, also set to program when programming the coolrunner
5-Now you can wire the motherboard and the coolrunner and the nand wires for your nand reader/writer
6-put mother board back in the cage before going to next step so many people short things out or get RROD from flexing mother board around or doing this on there bed or floor.
7 Now once you have wired everything and double checked your work its time to test your soldering. make sure the coolrunner is still set to Prog(program) and you can turn on the console to make sure there are no issues, being that the coolrunner is turned to Prog(program) it will not have power to the cool runner, If console boots normal, we can move to next step
"NOTE" if console doesn't boot after you wired everything you bridged something or have something touching.
8- Now time to turn the console off after you checked everything
9- keeping it hooked up to the power brick and av cables, you can now move to next step
10 - open j-runner program make sure your nand X or jr-Programmer or usb or lpt is detected.
11- make sure Glitch is marked and on J-runner
12- Dump the nands 2 times, or more if needed till they compare
13- once nands are compared Create the ECC. and always watch what is going on in the window of j-runner
14- Now Write the Ecc img should only take couple seconds will say done and make a sound when its done writing.
15- Now unplug your Nand X , jr programmer and usb or lpt.
16- Turn switch on the coolrunner to Nor(normal) the Red led should power on now showing that the coolrunner is activated
17- press the powerbutton or eject button to power the console on and it should boot with in seconds to Xell Reloaded to get your Cpu and Dvd Keys and make sure you write them down or take a picture of them you will need them for the next step
18- Now type in the Cpu key where it says Cpu key once you type it there it will say CPU is correct and load all the KV info.
19- Once you do that you can power off the console and hook back up your Nand x or jr-programmer or usb or lpt
20-Now its time to create the Freeboot img/updflash.bin so select the dash you want to make and press create and let it do its stuff it will make a folder with the serial number of the console and will be ready to write the nand now!
21- Once done you can now press Write nand and it will write the new img to the console.
22- It is best that after writen to unplug your nand x or device you are using to read and write to the console
23- Unplug the console from the power brick i believe they say for 2 minutes to reset the SMC , then plug it back in and boot the console .
24- One you turn it on the console the coolrunner should glitch just as i meant to meantion when you boot in xell.
25- The coolrunner green leds should flash about every 5 seconds untill it boots, lately I been getting them to glitch one time and some console boot instantly.
26- now you have completed your Reset Glitch Hack Console.
27- if you have any issue please read steps 5 thru 25 over again. if any other issues contact a member to help you
Pics
RGH 1
RGH 2
Slim RGH
Corona RGH
FAQ/ Troubleshooting
* problem one that usually happens
* problem two that usually happens
* Note: Just From my Experience I always use the blue wire instead of the the Low Loss cable the blue wire seems to work best for me.
* Console wont power on after RGH installed ? Always make sure your soldering points are correct bridge or short can cause this issue.
* Cool runner not Glitching? double check your wiring. make sure you programmed it correctly for the specific motherboard you have.
* Errors in j-runner when reading nand ? Restart j-runner, double check your nand wires. could be soldering issues , bridged wires can burn up your nand x.
Rodent:
RGH 1Coolrunner REV A, B. RGH 2.0 Coolrunner A, B & For Matrix Glitcher Boards & DGX For Slims for Cpu Keys
Coolrunner REV A For SLIM
Coolrunner REV A, B For XENON
Coolrunner REV A, B, Phat RGH2.0
Matrix Glitcher Phat And Slim Trinity
Matrix Glitcher Phat 2.0Zephry,Opus, Falcon, Jasper
DGXSlims Only at this time and for Dashboards 15574 16719 16202 and UpThis is used to retrieve your Dvd key
Step by Step
1- Get a full clean dump of your NAND before you do anything else
2- Trinity Dip #8: ON Corona DIP #8: OFF
3- Use latest J-Runner to write the DGX Ecc
4- Use latest J-runner to get your CPU KEY!
Modded Matt:
nice work rodent.
Rodent:
I think I have completed everything that is needed to know about RGH for now. I will be adding some more stuff for the corona boards If any one has anything I missed or needed to add please reply and i will add it asap.. this is fully up to date , if members have any questions feel free to ask. I wlll try to make a hands on video , of a rgh install
Anonamous:
Great job bro.
Just a side note, RGH 2.0 is extremely unreliable on falcon motherboards. I have ever got it to work on my falcon.
Navigation
[0] Message Index
[#] Next page
Go to full version