Author Topic: RGH2 Jasper Stuck - Random 0002 error?  (Read 7863 times)

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
RGH2 Jasper Stuck - Random 0002 error?
« on: June 29, 2015, 04:16:38 PM »
jasper rgh2. attached are pics of soldering and jr log

i read the nand fine, programmed coolrunner with timing file A fine, swith to fat,  create ecc, write ecc
i went to boot xell and get 0002 with both switch to fat and slim. Turned off console ,booted on green lights. Turned off, tried again 0002
I have checked all solder points for bridging, desoldered and resoldered

I have reflashed the original nand back to console, and console boots to retail every time. Reprogrammed coolrunner, still no go

coolrunner has jr and c8 removed, with 2-3 and cap bridged, switch to fat to program. when booting i switch to slim

should i try cr4 when writing ecc?

I am stuck



what's strange is im able to boot to green lights, then other times random 0002 sometimes instant 0002, other times it takes about 5 seconds for 0002 to show up

http://i.imgur.com/uvyvRN0.jpg
http://i.imgur.com/aHdi9FJ.jpg
http://i.imgur.com/wnuOZhY.jpg
http://i.imgur.com/wfKzscj.jpg
http://i.imgur.com/ol4xjr1.jpg




Sunday, June 28, 2015 8:01:24 PM

J-Runner v0.3 Beta (7) Started



Checking Files
Finished Checking Files
Glitch2 Selected
Checking Console..
Version: 03
Flash Config: 0x00AA3020
00AA3020
Jasper 512MB
CB Version: 6754
Version: 03
Flash Config: 0x00AA3020
00AA3020
Jasper 512MB
CB Version: 6754
Jasper 512MB Manually Selected
Reading Nand to C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\output\nanddump1.bin
Reading Nand
Done!
in 8:31 min:confused:ec

Reading Nand to C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\output\nanddump2.bin
Initializing nanddump1.bin..
Reading Nand
Jasper 512MB
Jtag Selected
Nand Initialization Finished
Done!
in 8:31 min:confused:ec

Comparing...Takes a while on big nands
Nands are the same

Programming Coolrunner
C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_A.xsvf
Version: 00
Wrong Arm Version.
Programming Coolrunner
C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_A.xsvf
Version: 00
Wrong Arm Version.
Programming Coolrunner
C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_A.xsvf
Version: 03
Flashing C:\Users\User\Desktop\JRUNNER\J-Runner v3 (5) Core Pack\common\xsvf\TX_RGH2_A.xsvf to CoolRunner
Input Filesize: 593E
Output Filesize: 2C82
Done!

Jasper 512MB Manually Selected
ECC created
Jasper 512MB Manually Selected
Version: 03
Flash Config: 0x00AA3020
Writing Nand
image_00000000.ecc
Done!
in 0:10 min:confused:ec
« Last Edit: June 29, 2015, 05:20:48 PM by Rodent »

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #1 on: June 29, 2015, 05:16:23 PM »
First of all you need to make your pictures smaller  I would check the orange wire or the red wire for power i am sure you have bridged a point its really hard to tell by these pics  there so large   

here in this pic your orange wire is bridged to  you need to redo it
[smg id=2969]
« Last Edit: June 29, 2015, 05:22:43 PM by Rodent »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #2 on: June 29, 2015, 06:13:12 PM »
sorry about the huge pictures - my error

regarding the orange wire, i re-did it 3x and i still have the same issue
i have actually desoldered and resoldered everything 3 different times
« Last Edit: June 29, 2015, 06:14:43 PM by jared911 »

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #3 on: June 30, 2015, 03:22:24 PM »
sorry about the huge pictures - my error

regarding the orange wire, i re-did it 3x and i still have the same issue
i have actually desoldered and resoldered everything 3 different times

when you created the ecc you made sure that the RGH2 was selected? and i can see in that pic that i showed you is why your getting an error  also if you flashed it r-jtag you will get this issue

 you also need to check the bottom of the motherboard where the power connects to the chip to make sure you havent bridged anything  and why are the nand wires not the normal colors? what are you reading and writing the nand with?
« Last Edit: June 30, 2015, 03:23:54 PM by Rodent »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #4 on: June 30, 2015, 03:48:39 PM »
when you created the ecc you made sure that the RGH2 was selected? and i can see in that pic that i showed you is why your getting an error  also if you flashed it r-jtag you will get this issue

 you also need to check the bottom of the motherboard where the power connects to the chip to make sure you havent bridged anything  and why are the nand wires not the normal colors? what are you reading and writing the nand with?

I'm sure i clicked RGH2 when creating ecc. i will try again to confirm. Yes i tried writing ecc with cr4 and got same issue, console is currently back to retail
I will check bottom of motherboard. Are you speaking of the 3.3 power?
Im using a 360 nand flasher by maximus. It's what i have always used and it works great

i will report back
thanks
« Last Edit: June 30, 2015, 03:50:37 PM by jared911 »

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #5 on: June 30, 2015, 04:48:23 PM »
I'm sure i clicked RGH2 when creating ecc. i will try again to confirm. Yes i tried writing ecc with cr4 and got same issue, console is currently back to retail
I will check bottom of motherboard. Are you speaking of the 3.3 power?
Im using a 360 nand flasher by maximus. It's what i have always used and it works great

i will report back
thanks

there is your problem your clicked CR4 when using a Coolrunner Rev c   

when using rev c coolrunner you just click glitch 2  no CR4  its a different chip

like i said you bridged the orange wire that i can see that cause the power issue and gives you a 0002  but if you flash it wrong you will get that error , just like if you use a R-jtag chip or the new CR4 jtag kit  you will get this error or  you usually get a 0020 , 0021 ,  0022 error i believe what the main rrod issues where its been so long since i have R-jtagged a console since they do not make those chips anymore 
« Last Edit: June 30, 2015, 04:52:12 PM by Rodent »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #6 on: June 30, 2015, 06:06:32 PM »
there is your problem your clicked CR4 when using a Coolrunner Rev c   

when using rev c coolrunner you just click glitch 2  no CR4  its a different chip

like i said you bridged the orange wire that i can see that cause the power issue and gives you a 0002  but if you flash it wrong you will get that error , just like if you use a R-jtag chip or the new CR4 jtag kit  you will get this error or  you usually get a 0020 , 0021 ,  0022 error i believe what the main rrod issues where its been so long since i have R-jtagged a console since they do not make those chips anymore

No, i tried just glitch 2 for days on end with no progress. I then tried cr4 to see if it would give me the same error and it did
I have re - done the orange wire 6 different times - no progress - i can always try the alternate underneath the motherboard?

just now
tried another coolrunner - reinstalled everything - now i get a 0010
reflashed original nand - boots to retail perfect

« Last Edit: June 30, 2015, 06:08:11 PM by jared911 »

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #7 on: June 30, 2015, 06:58:27 PM »
In the last photo, you have the cr switched on the program position. Switch it to normal and try again.

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #8 on: June 30, 2015, 09:47:04 PM »
In the last photo, you have the cr switched on the program position. Switch it to normal and try again.

i've actually done that already flipping both switches around trying to boot

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #9 on: July 02, 2015, 04:48:57 AM »
No, i tried just glitch 2 for days on end with no progress. I then tried cr4 to see if it would give me the same error and it did
I have re - done the orange wire 6 different times - no progress - i can always try the alternate underneath the motherboard?

just now
tried another coolrunner - reinstalled everything - now i get a 0010
reflashed original nand - boots to retail perfect




then there is a issue with your programming the coolrunner 

when you program the Coolrunner Rev c  click Glitch2  no CR4  timing file A 


make sure you are on  Glitch2 when you build the ecc  if not and its on jtag you will get errors!!

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline jared911

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #10 on: July 02, 2015, 03:51:53 PM »

then there is a issue with your programming the coolrunner 

when you program the Coolrunner Rev c  click Glitch2  no CR4  timing file A 


make sure you are on  Glitch2 when you build the ecc  if not and its on jtag you will get errors!!

i've made sure countless times i click glitch 2 and always use timing file A with jaspers.

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #11 on: July 03, 2015, 04:01:15 AM »
i've made sure countless times i click glitch 2 and always use timing file A with jaspers.


I notice this is a 512mb are you making sure that the jasper is building the proper ecc ?    and did you test the console with everything hooked up? before you dumped the nands?  make sure that E and F are in the right locations also   

I still believe your issues are here

http://i.imgur.com/uvyvRN0.jpg


 you can check it over and over,  i have had problems like this myself and  its either has a solder point bridged or you missed something 

it happens , even to the best of us
« Last Edit: July 03, 2015, 04:05:19 AM by Rodent »

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #12 on: July 03, 2015, 07:10:36 AM »
upload new pictures of your install. You said you tried another coolrunner but i see the same chip(both pictures have a slight stain in the exact same spots!). At this point send your nand file to someone here, either me or another user, and we will build an ECC image for you to try. If you are still getting errors and retail works fine, then the problem is with your install somewhere.

Yes, i am following your post on 2 different forums.

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Moderator
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: RGH2 Jasper Stuck - Random 0002 error?
« Reply #13 on: July 03, 2015, 08:03:36 AM »
upload new pictures of your install. You said you tried another coolrunner but i see the same chip(both pictures have a slight stain in the exact same spots!). At this point send your nand file to someone here, either me or another user, and we will build an ECC image for you to try. If you are still getting errors and retail works fine, then the problem is with your install somewhere.

Yes, i am following your post on 2 different forums.
Great . 2 different forums no wonder why he is having issues.   


to start over from the beginning,  0002 error is a power issue. there for like i stated the first time the power issues is where the orange wire is , it shorts out and gives an error or doesn't power on at all

thanks Gizmo for helping out ,  I go thru this everytime something thinks they can just jump in and rgh a console.   


@jared911 get some good pics and update what you have done recently . also upload the nands for me and send them in a PM to me and i will see what is going on

possibly try opening jrunner and press F12 just to make sure J_runner is fully updated

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal