« previous next »
Pages: [1]   Go Down

Author Topic: RB Button broken  (Read 3998 times)

Offline johnboy196

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
RB Button broken
« on: December 17, 2015, 11:51:38 AM »
Hi

My rb button on the main board stopped working so of course i desolder  the broken rb switch of the main board so i could  replace it with a new one everything went well..so of course when i went to replace the new rb switch this is where i messed up the 2 hole that power the switch i burnt out well over heated so there a no go ever time i try to solder the solder will not stay..so is there anywhere else i can power the rb switch from the switch stays in place but just does not work..as the solder points are broke..anyone help..?

Thanks..
Logged

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #1 on: December 17, 2015, 01:47:49 PM »
uploads some photos of the damaged points.
Also there should be a scan of the controller board on this forum somewhere, take a search and look.
Logged

Offline johnboy196

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #2 on: December 17, 2015, 02:03:13 PM »
thanks for replying ..yes was looking at the pictures of the scan board of the controller  that has been posted on the forum..just not sure where i could power my rb switch from..theres not much point in me uploading pictures of the damage i have done. the 2 hole that the pins go throw are shot and thats why the solder will not stay on the main board..so of course no power to switch dead..just thought i could solder a bit of wire to the pin of the leg that gives power to rb switch and then solder to the right point on the board but just not sure where..anyone..

Thanks for help
« Last Edit: December 17, 2015, 07:23:37 PM by johnboy196 »
Logged

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #3 on: December 18, 2015, 05:32:52 AM »
theres 4 holes that the pins go thru. you keep saying that 2 pads are destroyed but still are not telling us which 2 are destroyed.
Again, upload a photo so that we know for sure which controller board you have, and that we will provide you with the best help we can.
Logged

Offline johnboy196

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #4 on: December 18, 2015, 12:38:47 PM »
hi thanks for help and replying. i have looked on the forum and found the picture of the board that shows the 2 hole where the pins go through for the rb button.  its the hole that is highlighted  in purple and the hole down from it they are burnt damaged. are they the power points that are highlighted in purple and the over holes the ground..i cannot upload a picture of my board as my phone camera  is bad sorry..hope this explains it a bit better..

Logged

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #5 on: December 18, 2015, 04:12:12 PM »
you are gonna have to do a bypass/trace repair. you are going to have to scratch off the little vias that the purple line connects to. The other 3 holes are connected so you should be able to just jump a wire there.
Lower your heat and use flux when working with the vias. these are smaller and more eaily damage from heat.
Logged

Offline johnboy196

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #6 on: December 19, 2015, 11:08:36 AM »
Hi

Right thanks for replying..

Will give this a go and see how i get along hopefully this will get it sorted..

Will let you no how i get along...

Thanks again for your help..
Logged

Offline johnboy196

  • Guppy
  • *
  • Posts: 6
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #7 on: December 22, 2015, 09:51:09 AM »
Hi

Did like you said and all is working perfect..

so thanks again for the help..
Logged

Offline Gizmo613

  • MFH
  • Acid Modder
  • *
  • Posts: 547
  • Post quality +17/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #8 on: December 22, 2015, 11:43:53 AM »
Your welcome  :tup: :tup:
Logged

Offline PizzaInACup83

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #9 on: January 07, 2016, 06:03:28 PM »
Can someone tell me the size of the tact switch? 6x6x4.3 or 6x6x5, maybe I'm off on both? Thanks.
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: RB Button broken
« Reply #10 on: January 08, 2016, 10:36:02 AM »
Thru Hole, Right Angle, 6mm x 6mm x 3.85mm
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline PizzaInACup83

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: RB Button broken
« Reply #11 on: January 11, 2016, 08:22:46 AM »
Greatly appreciated!
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal