Author Topic: XB1 Controller Slim problem  (Read 987 times)

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
XB1 Controller Slim problem
« on: November 20, 2020, 05:09:30 AM »
Hello

I changed the left analog to a new one and when I installed it the line indicated by the arrow was separated. Then I connected it to the hole in front of it .. and now the analog gives commands forward and backward only and does not give a command above or below

please help me 

Offline wickated

  • King of the Wii-tards
  • *
  • Posts: 176
  • Post quality +0/-1
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #1 on: November 20, 2020, 09:49:11 AM »
you did nothing wrong exept buying :censored: replacement thumbstick

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #2 on: November 20, 2020, 10:04:32 AM »
ok why  above or below Do not respond

Offline wickated

  • King of the Wii-tards
  • *
  • Posts: 176
  • Post quality +0/-1
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #3 on: November 20, 2020, 02:27:19 PM »
ok why  above or below Do not respond
u mean left/right ? if so, solder wire from damaged thruhole to lowest hole of up/down stick.

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: XB1 Controller Slim problem
« Reply #4 on: November 20, 2020, 02:28:01 PM »
Jumper wire the spots with the Red dots together, then try it. If it still doesn't work, leave that jumper wire on there and then run another jumper wire from one of the Red spots to TP103.

Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #5 on: November 21, 2020, 04:48:28 AM »
thank you for reply mester RDC

When I connect a wire between the two points, the controller does not power up at all


Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #6 on: November 21, 2020, 04:51:11 AM »
u mean left/right ? if so, solder wire from damaged thruhole to lowest hole of up/down stick.


i meane up and down not work

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #7 on: November 21, 2020, 04:59:07 AM »
thank you for reply mester RDC

When I connect a wire between the two points, the controller does not power up at all




and are this the 103 you mentioned? 




Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #8 on: November 21, 2020, 06:12:31 AM »
Jumper wire the spots with the Red dots together, then try it. If it still doesn't work, leave that jumper wire on there and then run another jumper wire from one of the Red spots to TP103.



still up and down, not working . i mean LSY






Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: XB1 Controller Slim problem
« Reply #9 on: November 21, 2020, 07:36:35 AM »
That wire is a bit on the large side, you should be using a 30awg Kynar wire. That wire will work, but take care or it will tear off that TP spot.

If LSY is stuck Down, then the ground connection there could open. Jumper the 2 Black spots together.



If LSY is stuck Up, then move on, you can do better and don't need the hassle, also means the 1.8v is not getting to it and that wiring should have restored that, or there is some other issue on there shorting the Wiper (center pin) to ground.

If the controller is not turning on after doing that, then first undo it and check again.
« Last Edit: November 21, 2020, 04:33:49 PM by RDC »
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #10 on: November 21, 2020, 08:56:12 AM »
thanks for reply
LSY is not stuck up or down . it does not respond at all
analog responds back and forth
but it does not responds up or down
« Last Edit: November 21, 2020, 04:10:17 PM by RDC »

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: XB1 Controller Slim problem
« Reply #11 on: November 21, 2020, 04:22:26 PM »
Put a jumper wire from the center pin, the one between the Black and Red spots of the LSY POT, to TP63.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #12 on: November 22, 2020, 04:10:05 AM »
Put a jumper wire from the center pin, the one between the Black and Red spots of the LSY POT, to TP63.


this is TP63


Offline wwaaeell

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: XB1 Controller Slim problem
« Reply #13 on: November 22, 2020, 05:16:06 AM »

this is TP63




Thank you very much mester RDC you are a legend  :clap:

The controller now works very well  :tup:
« Last Edit: November 22, 2020, 05:17:32 AM by wwaaeell »

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal