« previous next »
Pages: [1]   Go Down

Author Topic: Elite Controller back buttons for normal controller  (Read 2333 times)

Offline halo2jumper

  • Chief squatting Hard
  • *
  • Posts: 10
  • Post quality +0/-0
Elite Controller back buttons for normal controller
« on: October 23, 2018, 02:01:45 PM »
Im trying to do a mod that uses the elite controller paddle board on a normal controller.

But im not sure if its possible when i look at the elite board.

Any pcb scans or diagrams available?


Im talking about this small board:




I basicly want to use this buttons for a normal controller.
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: Elite Controller back buttons for normal controller
« Reply #1 on: October 23, 2018, 04:15:57 PM »
It's just a common ground button board with a 6 pin connector.

1 - Button
2 - GND
3 - Button
4 - Button
5 - GND
6 - Button
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline halo2jumper

  • Chief squatting Hard
  • *
  • Posts: 10
  • Post quality +0/-0
Re: Elite Controller back buttons for normal controller
« Reply #2 on: October 24, 2018, 12:19:34 AM »
Ok but i want to solder the buttons directly to a normal one controller. Without using the pin connector.
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: Elite Controller back buttons for normal controller
« Reply #3 on: October 24, 2018, 04:33:30 AM »
No idea what you're really after then, as that board can't get any easier to figure out. You can see all of the FT spots and traces in your pic there.

FT1 - SW4
FT2 - SW3
FT3 - SW2
FT4 - SW1
FT6 - GND
FT7 - GND

Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline halo2jumper

  • Chief squatting Hard
  • *
  • Posts: 10
  • Post quality +0/-0
Re: Elite Controller back buttons for normal controller
« Reply #4 on: October 24, 2018, 10:31:00 AM »
Thats what i was looking for. Thanks for that <3
« Last Edit: October 24, 2018, 10:33:57 AM by halo2jumper »
Logged

Offline ndanielh

  • Guppy
  • *
  • Posts: 4
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Elite Controller back buttons for normal controller
« Reply #5 on: February 26, 2019, 08:16:06 PM »
and on the back that points would weld ??
Logged

Offline aakers369

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Elite Controller back buttons for normal controller
« Reply #6 on: November 08, 2021, 05:52:43 AM »
I know this is an old thread, but I am also doing this same thing. Everything is soldered up but I am now running into fitment issues. Were you ever able to successfully complete this mod? If so how did you fit the elite controller back onto the xbox controller?
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal