Author Topic: JDM-011 not recognized by PC or ps4  (Read 1989 times)

Offline Ditox

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
JDM-011 not recognized by PC or ps4
« on: April 20, 2021, 11:02:11 AM »
Hi everyone!...I have some troubles with a JDM-011 board. When i connect it by usb cable to my computer, it connects but is not recognized like if i had not the drivers.

I tried replacing the BD9200 chip and nothing happend. Something else is when i connect it and test the volt on the battery plug it isn't charging, there is not the 3,5v o 4v.

Any idea what can be the failure??  :dntknw:


Offline zis2104

  • Who Farted ???
  • *
  • Posts: 208
  • Post quality +0/-0
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #1 on: April 20, 2021, 01:04:40 PM »
Try remove touchpad flat

Offline zis2104

  • Who Farted ???
  • *
  • Posts: 208
  • Post quality +0/-0
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #2 on: April 20, 2021, 01:10:41 PM »
Or replace ribbon cable usb

Offline maki

  • Fart Sniffer
  • *
  • Posts: 40
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #3 on: April 21, 2021, 06:12:31 AM »
Hi everyone!...I have some troubles with a JDM-011 board. When i connect it by usb cable to my computer, it connects but is not recognized like if i had not the drivers.

I tried replacing the BD9200 chip and nothing happend. Something else is when i connect it and test the volt on the battery plug it isn't charging, there is not the 3,5v o 4v.

I've changed broken BD92001 for other broken BD92001 (without knowing that they were broken) in the past.. didn't help.

There is test points around that chip, what values do you measure against ground from them?
« Last Edit: April 21, 2021, 06:12:54 AM by maki »

Offline zis2104

  • Who Farted ???
  • *
  • Posts: 208
  • Post quality +0/-0
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #4 on: April 21, 2021, 04:37:20 PM »
I've changed broken BD92001 for other broken BD92001 (without knowing that they were broken) in the past.. didn't help.

There is test points around that chip, what values do you measure against ground from them?

have you ever tried to reball the same chip? And has it ever worked again?

Offline maki

  • Fart Sniffer
  • *
  • Posts: 40
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #5 on: April 22, 2021, 03:24:44 AM »
BD92001 is not a BGA, no reballing required or even possible, just add the right amount of solder

if an IC is broken its broken, swapped around 4 until I found one that was working, thats why I've ordered new ones, at least I hope they are new (new old stock)
« Last Edit: April 22, 2021, 03:25:40 AM by maki »

Offline Ditox

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #6 on: April 28, 2021, 08:41:49 AM »
I have the same problem with a JDM-011, every capacitor and resistor near the BD9200 gets a right voltage but there is a diode up to the battery connector that doesn't feed with 3,4v this connector i'll trie to change it...you should check that.

But i think it won't solve the recognized problem...i'm still looking how to solve that

Offline Ditox

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #7 on: April 28, 2021, 10:14:25 AM »
have found a resistor that has a line from the MB9BF002A IC, i think is the processor...well this resistor give a measure in diode mode of 0.017 i think this IC is the principal problem, what a mess!  :sadno:

Offline Ditox

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #8 on: April 28, 2021, 12:45:57 PM »
Finally i could find the problem, it wasn't the IC, think is a diode that was causin the problem, it makes a resistor change its value. I changed it and it was done, now my pc recognize the control. This is the diode i mean...https://imgur.com/qqtT65M
« Last Edit: April 28, 2021, 12:47:04 PM by Ditox »

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: JDM-011 not recognized by PC or ps4
« Reply #9 on: April 28, 2021, 01:04:51 PM »
Arrow is pointing to a Resistor, 27ohm, 0402.

Circled component is a TVS array for the USB data lines.
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline Ditox

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #10 on: April 28, 2021, 02:24:00 PM »
Correct, the TVS was damage and afected that resistor... after i changed it the computer recognized the controller and its working now  :victory:

Offline frds125

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-011 not recognized by PC or ps4
« Reply #11 on: September 09, 2022, 01:39:05 AM »
What is the part number for the TVS Array and the diode replacement? Having the same problem but can't find the parts needed. I looked at the TVS and it has 06F written on it. Googling found nothing.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal