Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => PS4 => Topic started by: jetuaime81 on October 08, 2022, 12:23:40 PM

Title: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 08, 2022, 12:23:40 PM: My ds4 V1 with board jdm-011 is not charging the battery or turning on when i press ps button. I am able to connect to pc via usb cable and with "ds4 windows" ,all buttons (including PS), analog controls, touchpad and rumble are working; I can even change colour on the lightbar.

There is no heating or battery discharge when kept idle. I checked almost all caps for shorts and reflowed the ARM bga chip MB9BF002A but no success. I am getting 5v and 2V and same resistance near the BD9200 as said in this post.

https://acidmods.com/forum/index.php/topic,44878.msg337252.html#msg337252 (https://acidmods.com/forum/index.php/topic,44878.msg337252.html#msg337252)

Any suggestions? Thanks in advance.
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 08, 2022, 10:06:25 PM: UPDATE:

I RAN SOLDERING IRON ON COMPONENTS (EVEN THOUGH SOME WERE INACCESSIBLE, HOPING TO FIX ANY COLD SOLDER JOINTS THAT MAY HAVE FORMED).

AS OF NOW THE BATTERY IS CHARGING BUT NO PULSING LIGHT. AS BEFORE, CONTROLLER IS WORKING PERFECTLY VIA USB. BUT STILL CONTROLLER DOES NOT TURN ON WITH BATTERY.

AND NOW I HAVE A NEW PROBLEM; BOARD IS DRAWING 40mA FROM BATTERY ON IDLE. CANT SENSE HEAT ANYWHERE, CANT FIND SHORTED COMPONENTS :eyebrow:
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: RDC on October 10, 2022, 12:50:21 PM: You really need a hot air station to reflow/rework those kinds of parts properly.

The BD9200 chip is the PMIC, it does all of the regulation and such, but the battery charging is done by the TC7710WBG, the small chip on the top side of the board marked 7710. https://acidmods.com/forum/index.php/topic,44560.msg334920.html#msg334920
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 10, 2022, 09:55:44 PM: Battery is charging properly so i guess the charging circuit is ok??!!! i dont know . But when i remove charger, the board is drawing around 45mA in idle / off state and so the battery discharges completely in about 17 to 20 hours.

I checked a working jdm-055 (i dont have another 011), the moment i plug in battery, the board draws 35mA for about 2 seconds (i guess for initialization) and then 0mA. But my jdm-011 takes 45mA on plugging battery and doesnt return to 0.

I already reflowed MB9BF002A. I will try reflowing the 7710 chip you mentioned.
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 11, 2022, 07:50:27 AM: Need value of this resistor accidentally removed while reballing IC

https://ibb.co/W2xLgwn (https://ibb.co/W2xLgwn)
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: RDC on October 11, 2022, 08:06:25 AM: If that's a picture of your actual board, that USB data line protection chip looks toasted and will cause issues.

Resistor is 100ohm
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 11, 2022, 08:20:12 AM: No sorry that is from reddit. This is my controller board

1 (https://ibb.co/hffjxfc)
2 (https://ibb.co/L5LsyQH)
Title: Re: Jdm-011 not charging and not turning on; works via usb
Post by: jetuaime81 on October 11, 2022, 11:16:52 AM: RDC. Its working now. So what I did was take out 7710 and mb9bf chip and reball them and put back. The 100ohm resistor was lost i think it's size is 0201. I only have 0402 and above :-(. So i soldered wire to 100ohm 0402 and tested.

https://ibb.co/m4HYhS8 (https://ibb.co/m4HYhS8)

I don't have microscope. Anyway controller is working now wirelessly. I will order some 0201 from AliExpress but it will take 2 months (not available in my country).

Thanks to you i fixed 2 controllers from trash :-).