Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => XBOX 360 => 360 Controllers / 360 Rapid Fire Controllers => Topic started by: RDC on January 14, 2010, 08:04:57 PM

Title: Wireless CG2 Traces
Post by: RDC on January 14, 2010, 08:04:57 PM: TOP
(https://www.acidmods.com/RDC/360/WirelessCG2v2Top.jpg)

BOTTOM
(https://www.acidmods.com/RDC/360/WirelessCG2v2Bottom.jpg)

TP1 - N/A
TP2 - Ground
TP3 - B+
TP4 - Ground
TP5 - B+
TP7 - Ground
TP8 - Analog Voltage, 1.5v (Switched)
TP9 - DR
TP10 - Light Rumble
TP11 - Heavy Rumble
TP12 -
TP13 -
TP15 -
TP16 - N/A
TP17 - Ground
TP18 -
TP19 -
TP20 -
TP21 - USB D- (PnC Cable)
TP22 - Ground
TP23 - USB D+ (PnC Cable)
TP26 -
TP400 - Ground
TP405 - Antenna
TP407 - Ground

LED TRACES
(https://www.acidmods.com/RDC/360/WirelessCG2LED.jpg)
Title: Re: Wireless CG2 Traces
Post by: Rodent on December 10, 2011, 03:38:07 AM: Would anyone know if they have pic showing the trace for the leds on cg2 or is it the same a cg?
Title: Re: Wireless CG2 Traces
Post by: Anonamous on December 10, 2011, 09:26:50 AM: Quote from: Rodent on December 10, 2011, 03:38:07 AM
Would anyone know if they have pic showing the trace for the leds on cg2 or is it the same a cg?

It is most likely not the same bro.
Title: Re: Wireless CG2 Traces
Post by: DarkSydeCraZe on December 20, 2011, 09:31:04 PM: Noob here. How would I solder/hookup a wire to the holes (eg. the Y button).
I was planning on wiring a momentary switch to it.
Any reply is greatly appreciated.
Title: Re: Wireless CG2 Traces
Post by: FOOKz™ on December 21, 2011, 05:29:41 PM: Quote from: DarkSydeCraZe on December 20, 2011, 09:31:04 PM
Noob here. How would I solder/hookup a wire to the holes (eg. the Y button).
I was planning on wiring a momentary switch to it.
Any reply is greatly appreciated.

Take sandpaper and sand the green part off of your circuit board to expose the copper trace underneath.
Title: Re: Wireless CG2 Traces
Post by: RDC on April 14, 2016, 02:17:28 AM: Use and Xacto knife or fiberglass pen to remove the solder mask at the Y via, and then some 30awg Kynar wire.

Controller shown is NOT the G2, this is only for an example of how to prep and solder to a Via.

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi50.photobucket.com%2Falbums%2Ff320%2FRDCXBG%2FRepair%2F02ViaWire.jpg&hash=f37d8ca94550f7047632696d5412678351c7657d) (http://s50.photobucket.com/user/RDCXBG/media/Repair/02ViaWire.jpg.html)

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi50.photobucket.com%2Falbums%2Ff320%2FRDCXBG%2FRepair%2F03ViaWire.jpg&hash=0a0834f2546ff796fa9463c9e59c97392e5c1cf8) (http://s50.photobucket.com/user/RDCXBG/media/Repair/03ViaWire.jpg.html)

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi50.photobucket.com%2Falbums%2Ff320%2FRDCXBG%2FRepair%2F05cViaWire.jpg&hash=c5236ef7d0ed891e425301f6a4bd637b17ceabbe) (http://s50.photobucket.com/user/RDCXBG/media/Repair/05cViaWire.jpg.html)

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi50.photobucket.com%2Falbums%2Ff320%2FRDCXBG%2FRepair%2F06ViaWire.jpg&hash=5105e733b9f6913e5695aa7f5e1028b2ce11eb48) (http://s50.photobucket.com/user/RDCXBG/media/Repair/06ViaWire.jpg.html)

(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi50.photobucket.com%2Falbums%2Ff320%2FRDCXBG%2FRepair%2F12ViaWire.jpg&hash=a38518ff8e4f5fcff663d22eb1b4ecfefc2fc641) (http://s50.photobucket.com/user/RDCXBG/media/Repair/12ViaWire.jpg.html)