Acidmods
Console Modding------ ( Here you can talk about your favorite Consoles ) => PSP's => PSP Phat (1000) => Topic started by: Darkzero on December 07, 2008, 07:26:24 AM
-
First off, I read through all the tutorials that you guys posted, and I understand them for the most part. There's just areas of confusion for me that I really need cleared up.
My first place of confusion is regarding the LED trigger mod. The tutorial maker posted this picture:
(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fimg265.imageshack.us%2Fimg265%2F9026%2Fpowertoppj9.jpg&hash=8852361964ee8863312afb3322b2b0d5dd95d0c6)
Instead of soldering the Negative wire there.. Why can't I just solder it somewhere in the ground space that is mentioned in this picture (it says "This whole area is ground plane"):
http://i337.photobucket.com/albums/n384/ALien_X_2008/pwrbrd_front.png
And, If i can just solder it to that ground plane, do i have to solder the wire onto one of those little holes?
My second question, after calculating my resistor, I need a 20ohm resistor..which doesn't seem to exist. Instead of a 20ohm resistor, can I use two 10ohm resistors?
My last question regards the amount of room available for extra LEDs. Most of the power source for the LEDs is that little patch of 3.6v+ red, right? It doesn't look like much..what happens when you run out of room?
Thanks for clearing things up.
-
First off, I read through all the tutorials that you guys posted, and I understand them for the most part. There's just areas of confusion for me that I really need cleared up.
My first place of confusion is regarding the LED trigger mod. The tutorial maker posted this picture:
(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fimg265.imageshack.us%2Fimg265%2F9026%2Fpowertoppj9.jpg&hash=8852361964ee8863312afb3322b2b0d5dd95d0c6)
Instead of soldering the Negative wire there.. Why can't I just solder it somewhere in the ground space that is mentioned in this picture (it says "This whole area is ground plane"):
http://i337.photobucket.com/albums/n384/ALien_X_2008/pwrbrd_front.png
And, If i can just solder it to that ground plane, do i have to solder the wire onto one of those little holes?
My second question, after calculating my resistor, I need a 20ohm resistor..which doesn't seem to exist. Instead of a 20ohm resistor, can I use two 10ohm resistors?
My last question regards the amount of room available for extra LEDs. Most of the power source for the LEDs is that little patch of 3.6v+ red, right? It doesn't look like much..what happens when you run out of room?
Thanks for clearing things up.
The LED's will never shut off. You would have to add an extra switch.
That or scratch some green off until you see copper and solder to that.
Yeah that will work fine :D
What? lol
-
The LED's will never shut off. You would have to add an extra switch.
I want to have like, 8 LEDs in my PSP total. I know there's no way i'm going to have enough space on that little itty bitty negative LED thing to solder so many wires to it. Where else can I connect the negative end to that will cut off the LEDs when the PSP is cut off?
And thanks for the help ^-^
-
I want to have like, 8 LEDs in my PSP total. I know there's no way i'm going to have enough space on that little itty bitty negative LED thing to solder so many wires to it. Where else can I connect the negative end to that will cut off the LEDs when the PSP is cut off?
And thanks for the help ^-^
Just make everything join together onto one wire, then that one wire goes to negative (Im assuming your putting those LED's in parrelell, but anyway a series would have one negative anyway)
-
You can solder anywhere in that ground plane, jumbo is wrong :boxed:
-
Just make everything join together onto one wire, then that one wire goes to negative (Im assuming your putting those LED's in parrelell, but anyway a series would have one negative anyway)
I was planning on splitting up the mods though. I was going to do the trigger mod first, then the lighted ring mod at a later time. :l
-
you could do your first mod then when you ready for the next one just melt some of the plasic off your wire where it will fit and solder another wire on that then put either heat shrink or electrical tape to prevent shorts. would look something like this:
(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi160.photobucket.com%2Falbums%2Ft188%2Fdeamonblade%2Funtitled.jpg&hash=153cf4b3412ec88ffde9167b77b4b58280d6ff88)
-
You can solder anywhere in that ground plane, jumbo is wrong :boxed:
I never said you couldnt you can but it will never shut off...
-
I never said you couldnt you can but it will never shut off...
Are you sure? :/
-
The LED's will never shut off. You would have to add an extra switch.
yes he is sure...
-
I never said you couldnt you can but it will never shut off...
You are wrong though.
It will shut off.
-
You are wrong though.
It will shut off.
Only way is if he takes out the battery. That plane is always grounded. Unlike the trace that we tell yo to ground the leds on that is only grounded while the power led is on.
I am 100% positive i checked twice...
-
Okay, but is the positive point always true?
Long time since I did this now though, so you could be right.
-
Just use your wifi switch to controle you leds wow
-
LaCozte can you post how to? I've searched and have only found microsoft paint looking pictures. Any other pictures would be great. I've been wanting to do this for awhile but can't get my hands on 0603 blue leds.