Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => PSP's => PSP Slim (2000) => Topic started by: miah23sky on March 16, 2009, 01:24:08 AM

Title: help..other 5v supply (lordnico's tut)
Post by: miah23sky on March 16, 2009, 01:24:08 AM

 :help: hey guys..can you pls point me to other 5v supply to connect my +wire from the lm386..im following lordnico's tut and for sure that is a great tut but im not that good at soldering and the 5v supply to solder to is pretty small,,pls help this is the last step to finish my mod..pls pls pls.... :beg:

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Friguletz on August 06, 2009, 03:20:54 AM

help us pls! :|

Title: Re: help..other 5v supply (lordnico's tut)
Post by: bustinthejustin on August 06, 2009, 11:43:07 AM

there isn't an easier point as far as i know...

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Friguletz on August 06, 2009, 01:28:26 PM

if i removed the rezistor from the +5v will i still get voltage for the mod ? :| :beg:

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Jumbo on August 06, 2009, 01:45:29 PM

Ya but you would need it there to have the Memory LEd still work.

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Friguletz on August 07, 2009, 04:23:30 AM

and if the led dosent work that means that my mod is dead ?

Title: Re: help..other 5v supply (lordnico's tut)
Post by: ApheX on August 08, 2009, 01:59:40 AM

Well it depends. As long as the wire is soldered to the 5v point it will work. As for the memory led, you can always bridge (solder over) the resistor to get it working, but it will be very bright.

Guys I know it's a really small point but it's the only one that you'll find to be the easiest to solder. Other points are on the Zif connectors and are an absolute pain to solder too if your not confident doing so. I'd also recommend using flux when soldering to that 5v point. It will make the job alot easier for you.

Title: Re: help..other 5v supply (lordnico's tut)
Post by: ryan on August 08, 2009, 10:58:34 AM

Hey I think you can solder right to where the battery connects to the mother board.  If you are looking at the battery terminal it has three connections on the top and on the bottom and im pretty sure the one on the top all the way to the right is 5v.

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Friguletz on August 08, 2009, 02:17:51 PM

ok.. so let my think... now my rezistor from the +5v is removed... so if i put solder over the 2 contact the led will be ok.. but mutch brighter(the memory).. and if i solder the wire to the point where i soldered the +5v will my mod work ? is there any chance that the mod will not work ?


sorry for my bad english! :|

Title: Re: help..other 5v supply (lordnico's tut)
Post by: ApheX on August 09, 2009, 02:17:14 AM

As long as you have soldered over where the resistor was then it will work, both the memory led and your mod.

Just some advice, After you have soldered the power wire to the 5v point, use some glue or tape to secure the wire to the mobo. This will stop it moving and possibly breaking off when rebuilding the psp.

Title: Re: help..other 5v supply (lordnico's tut)
Post by: Friguletz on August 09, 2009, 04:37:27 AM

ok.. thanks... hope i will make it :)