Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => XBOX 360 => 360 Controllers / 360 Rapid Fire Controllers => Topic started by: mikespartian114 on August 24, 2009, 02:32:57 PM

Title: led set up ?
Post by: mikespartian114 on August 24, 2009, 02:32:57 PM

i have a martix wireless and i am using a 10mm blue led (3.2/20mA) for dome and of "Y" a 5mm (1.8-2v/20-30mA), "X" (3.1-3.8/20-30mA) "A" (2.8-3.2/20-30mA) and "B" (3.1-3.8/20-30mA), i would like a wireing diagram so that the can be put on a switch and so that the x,y,a,b buttons are lite at around the same brightness? if this is posible i need help i cant figure how to get them the same brightness

Title: Re: led set up ?
Post by: Modded Matt on August 24, 2009, 03:30:28 PM

for matrix, you will have to use the battery supply to get that much FV..you will need a diff resistor on each diff led. google led resistance calc..and you will need to put a on/off switch on the controller some where.

Title: Re: led set up ?
Post by: Jumbo on August 25, 2009, 01:39:01 PM

You can always just use white LED's for the buttons and it looks the same. You dont need to match the colors it barely makes any difference.

Title: Re: led set up ?
Post by: laxboy on August 25, 2009, 05:28:45 PM

Jumbo is right here is a good tut on lighting the buttons http://www.llamma.com/xbox360/mods/xbox%20360%20Controller%20LED%20Mod.htm (http://www.llamma.com/xbox360/mods/xbox%20360%20Controller%20LED%20Mod.htm) that should help you out

Title: Re: led set up ?
Post by: phenoptix on August 26, 2009, 03:53:48 AM

After a fair bit of playing around with different LEDs I'd have to agree with Jumbo that white is better, they look consistent.
I saw recently using SMD LEDs for the buttons looks pretty good and only requires removing a small amount of the white plastic in the button. You do of course have to prewire an SMD to a length of wire but PSP modders seem to have no trouble with that!
Personally I thought that 4 x 3mm LEDs made for a better dome light.
Using all white, which are usually a max of 3.4V or so, you won't really need resistors. As you won't get more than 3V off of the batteries.

Title: Re: led set up ?
Post by: Modded Matt on August 26, 2009, 05:36:39 AM

yea, but I have ruined a many smd leds like that. lol.. I think a through mount 0603 led bight be better. I am ordering some this weekend, and saving my smd leds for applicatins that acctually need a surface mounted device

Title: Re: led set up ?
Post by: Ben. on August 26, 2009, 06:36:34 AM

I did it with white SMD's and it looked alright in the dark fully charged - but not as good during the day. and I didn't remove any white plastic, just slide them in..
(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Frapidcontrollers.co.uk%2FGallery%2FABXY%2520Lights.JPG&hash=16d71fecaa0a2bbc94f2b8b7bc0bc08b2d585ed1)

The only thing is they stayed on constantly, as I just wired them to the main power points in the center of the controller..

Title: Re: led set up ?
Post by: lilunwl on August 26, 2009, 08:29:42 AM

Ben I seen that you wrote you didnt remove any white plastic....  I just want to make sure I understand right. You did not have to drill out the 4 white plastic sticks inside the buttons? I have tried lighting without taking them out and have had no luck!! Props!!!! I have also used SMD 0603 LEDs as well and I think the buttons are a bit more colorful rather than bright. Anyways great job!!!

Title: Re: led set up ?
Post by: Ben. on August 26, 2009, 08:31:59 AM

Yer, I just wired the LEDs up and put a dab of hot glue on them to strengthen them, and slide them inside the button and trimmed part of the rim of the button to lead the wires out, and it worked out quite nicely - shame they aren't too bright.

Title: Re: led set up ?
Post by: phenoptix on August 27, 2009, 02:02:25 AM

I think they look pretty good. I wonder if a PLCC-2 LED would be ok, they're a higher spec but bigger. I may have to head to the shed to test it out this afternoon.
How's your mod coming along mikespartian114?

Title: Re: led set up ?
Post by: mikespartian114 on August 27, 2009, 01:04:41 PM

well i reasembled it yesterday
(https://acidmods.com/forum/proxy.php?request=http%3A%2F%2Fi786.photobucket.com%2Falbums%2Fyy148%2Fmikespartian114%2F100_0540.jpg&hash=18b14ece152cde041966ea1eea22ebb6fe7e0eea)
but i wanted some leds in it, i just got some blue SMDs , but i am gona wait til i draw up a wire diagram so i have a plan and no just sodring stuff together lol

Title: Re: led set up ?
Post by: Jumbo on August 27, 2009, 07:48:38 PM

What in the blue hell is on your analogs?! >.>

Title: Re: led set up ?
Post by: blackburn on August 27, 2009, 08:00:05 PM

Quote from: Jumbo on August 27, 2009, 07:48:38 PM

What in the blue hell is on your analogs?! >.>

they look like theyre analog sticks, that were chewed by a dog, then stuck on top of the original joysticks. this controller definitely has A LOT going on

Title: Re: led set up ?
Post by: Modded Matt on August 28, 2009, 05:00:17 AM

uea, those sticks look pritty narly..mike, can you list all the mods on that controller? I see like 4 tact switches, three led indicators, a serial port...????

Title: Re: led set up ?
Post by: laxboy on August 28, 2009, 10:42:11 AM

ya those deffenitly cant be comferatable

Title: Re: led set up ?
Post by: blackburn on August 28, 2009, 01:32:14 PM

almost as comfortable as putting sewing needles in them and gouging them into your fingers. That way the "my finger slipped off the joystick" excuse is no longer.  :rofl:

Title: Re: led set up ?
Post by: mikespartian114 on August 28, 2009, 08:42:15 PM

two rumble motor leds red one for each side, Blue dome only on when controler is,1st blue 2nd red 3rd brd and 4th blue rol, middle tack program button for RF/Burst and other to tacks for speeds, RF on the trigs and internal mic with head set jak a.k.a ipod head phones. posting pic and vid on show off controler section soon