Acidmods
Console Modding------ ( Here you can talk about your favorite Consoles ) => PS3 => Tutorials => Topic started by: whitetop on March 13, 2011, 02:39:58 PM
-
PS3 sixaxis ps led
Introduction
nice color in your ps button
the start of pimping your controller out
(https://www.acidmods.com/moddedmatt/whitetop%20psled1.jpg)
Parts Needed
- - 3 volts LED - (3mm recommended) Any color
- 1/4 watts 47 Ohms Resister
- 30cm gauge wire
- PS3 controller
- Tiny Phillips screw driver
Tools Needed
- solder iron 15-30 watt
solder
3mm led of your chosen color
flux
30cm wire ( depends were your putting the wire)
Difficulty rating:
3/5
Average Time to Complete:
1hr-2hr(depends on soldering skill)
Step By Step Tutorial
1.take apart your ps3 controller
1.1:undo the screws
(https://www.acidmods.com/moddedmatt/whitetop%20psled2.jpg)
push down the bottom part to unclip
(https://www.acidmods.com/moddedmatt/whitetop%20psled3.jpg)
(https://www.acidmods.com/moddedmatt/whitetop%20psled4.jpg)
1.2:unplug the battery and pull the board out from the case watching out for the r1 l1 buttons and the spacers by them
pull the thumb sticks off.
2:
solder your parts
(https://www.acidmods.com/moddedmatt/whitetop%20psled5.jpg)
3:ok now turn your board so the back is facing you
and find your power points(these points work on all the controller as from first to the newest )
negative(your mini usb)
(https://www.acidmods.com/moddedmatt/whitetop%20psled6.jpg)
positive(this picture is from the right side thumb stick)
(https://www.acidmods.com/moddedmatt/whitetop%20psled7.jpg)
4:now plug your battery in and press the ps button to see if the led comes on if so congrats if o light comes on check to
see if you put the wires in the right place.
(https://www.acidmods.com/moddedmatt/whitetop%20psled8.jpg)
5: now get your rubber thing from the front part of your case were the ps button is.
make a hole in it but make sure to not cut past the pads.(this is were the light will be coming through)
(https://www.acidmods.com/moddedmatt/whitetop%20psled9.jpg)
6:get your supporter and cut the middle part out this is were your leds going put it in after the cutting and glue it in place.
(https://www.acidmods.com/moddedmatt/whitetop%20psled10.jpg)
(https://www.acidmods.com/moddedmatt/whitetop%20psled11.jpg)
7:once all this is done and things are ok put your controller back together and try your led installation out to make sure you have not knocked a wire or anything
(https://www.acidmods.com/moddedmatt/whitetop%20psled12.jpg)
FAQ/ Troubleshooting
- wire could come off if not soldered right
- if resisters not put in right can stop you closing the case fully
-
Nice tut whitetop :tup: i think to have less problems when you assembly your controller again you could do this mod with a 0603 smd led. I think i saw it in another forum
-
not sure to lock this since its a tut
you can do this with 0603-0805 leds but most people cannot solder them so a 3mm/5mm they can
-
Yeah i did this with 0603 and with no resistor.
Glued the SMD in place inside the cut in the rubber
-
nice im gonna do like 3 leds tho to mine :)