Acidmods
AcidMods Resources ----- ( These are helpful tools for modding ) => Electronics Projects => Topic started by: 1TONpete on September 08, 2011, 05:49:54 PM
-
I need to make a box that I can use to cure my acrylic parts . I want to vent to the out side through a window or something. Inside the box I need to keep it at 100f min. But not hot enough to melt stuff. I was thinking about an old computer case maybe and put some racks inside. seal it up and make a vent out the back. But what do I use to heat the box?
-
nichrome heating element wire. Found in hair dryers/heatguns. Just use a high power rheostat or a light dimmer switch to adjust your heater.
When you wrap your wire insulate the wire with ether mica, ceramic, or asbestos.
There are good thermal and electrical insulators. I've seen stuff called ZetexPlus which is a thermal and electrical insulator fabric you can buy which does the same thing but its probably not cheap.
-
I was thinking ceramic heater maybe. Don't like the idea of the fumes mixing with an open element.
1 thing I was thinking about was a 12vpeltier mounted to a heat sink fan combo.
-
nichrome heating element wire. Found in hair dryers/heatguns. Just use a high power rheostat or a light dimmer switch to adjust your heater.
When you wrap your wire insulate the wire with ether mica, ceramic, or asbestos.
There are good thermal and electrical insulators. I've seen stuff called ZetexPlus which is a thermal and electrical insulator fabric you can buy which does the same thing but its probably not cheap.
umm I would say dont use asbestos lol
-
umm I would say dont use asbestos lol
But it works and I see it used all the time... yes its a carcinogen...
-
lulz I was like waaaaaaaaaaaaait this topic on AM no Way! I came and I was like Oooooooooh ha ha I was thinking something else. But uh Asbestos is bad for your health.
-
not sure exactly how hot they get but maybe try one of them cheap peltier based mini fridges, I have one and there is a switch to select whether it heats or cools :)
-
lulz I was like waaaaaaaaaaaaait this topic on AM no Way! I came and I was like Oooooooooh ha ha I was thinking something else. But uh Asbestos is bad for your health.
lmao i thought the same thing i was GOING to say the shower works lmao why not try a toaster oven just modfiy it a bit
-
1TONpete , you can easily make a HOTBOX or its what they call a Curing oven, with some simple items. 5/8 dry wall its flame retardant. this is what they put on the walls between the garage and house when you have a attatched garage (required by law) would framed box on the outside dry wall on the inside, small space heater to blow the hot air in and you can control the temperature that Way some 12 volt fans, or use like I have, a 6"x 6" 110volt fan for air flow and exhaust to out side,
Build a wood frame , as big as you want the curing oven to be. dry wall the inside of the frame, and insulate the out side of the frame. you can get Cookie cooling racks cheep to place on the inside to set your parts on or cookie sheets, this works well I have made these a few times for a company I worked for except larger that you could walk in to. For curing poly urethane parts and rubber compression parts. works well stays around a 120 degrees but you could drop the temperature to what you needed. and exhaust fans to draw out any harsh smells. could use drier duct to vent to out side, if you dont have 5/8s dry wall just double up 1/2 inch dry wall aslong as its over 5/8 of inch think you will be good to go and your parts will turn out great,
Expected cure time will cut your curing time in half , probably only need it in there couple hours, poly urethane usually cures with in,24 hours max cure time, for durometer reasons.
Durometer( hardness of the material) this is how they rate poly urethanes, soft to harder 30a 40a 50a 60a 70a 80a 85a 90a 95a
these are like a brick 65d 75d
EDIT seriously guys really think he would post that here? :rofl:
-
Thanks guys,
Rodent, I used be a drywall finisher, lol. nice thought on the 5/8s. Round here we call it purple board because its purple instead of blue/green. I can make the box, I am just looking for ideas on heating/ventilation. I would like to stay around 12v range because im thinking bout using a 12v ps2 power supply . Thinking pc equipment. Anyways thanks everyone for your input so far. The device is going to be window shelf mounted.