« previous next »
Pages: [1]   Go Down

Author Topic: Ground Pin?  (Read 2592 times)

Offline ReZiN_420

  • Chief squatting Hard
  • *
  • Posts: 17
  • Post quality +0/-0
  • Gender: Male
  • Moding is not a hobby, it's a habit
Ground Pin?
« on: July 08, 2008, 08:07:44 PM »
Hi, I need what seems to be an obvious answser :dntknw:.....but, would this be the ground pin to solder to for razor x on the slim?



Sorry for crudy drawing, im not exactly art team material :sadno: :laughing:. Oh and if i could hear from someone who has already done this mod, much obliged.
Logged

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: Ground Pin?
« Reply #1 on: July 09, 2008, 05:28:42 PM »
Dude, just post a pic of the point you want to solder rather than draw a diagram. makes thinks easier for us to help. :)
Logged

Offline ReZiN_420

  • Chief squatting Hard
  • *
  • Posts: 17
  • Post quality +0/-0
  • Gender: Male
  • Moding is not a hobby, it's a habit
Re: Ground Pin?
« Reply #2 on: July 09, 2008, 07:09:38 PM »
Ok heres the pic, my questions are is that the ground pin and is my diagram right?





And sorry bout the bright colors but dark ones couldn't be seen right.
Logged

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: Ground Pin?
« Reply #3 on: July 10, 2008, 01:50:33 AM »
Hey dude! nice one. That i'm aware of that is the ground, but i'd check with other members to make sure. Hopefully someone here will post a reply to confirm it. :)
Logged

Offline ReZiN_420

  • Chief squatting Hard
  • *
  • Posts: 17
  • Post quality +0/-0
  • Gender: Male
  • Moding is not a hobby, it's a habit
Re: Ground Pin?
« Reply #4 on: July 11, 2008, 03:48:41 PM »
Alright man thankx for the advice, its all i need to get the go ahead.
Logged

Offline l0rdnic0

  • 2%
  • Acidmods Alumni
  • E = MC² Mad Scientist
  • *
  • Posts: 1836
  • Post quality +8/-0
  • Gender: Male
  • TeamCYBER

Re: Ground Pin?
« Reply #5 on: July 11, 2008, 04:56:08 PM »
Yeah that middle section is the ground. If you search you will find a pic from TimmyDX (i think) that shows other points on the MB that you might find easy to solder to.
Logged


L0rdNiC0 Pioneering Mods on the PSP Slim :taunt:
Sound Mod, Button LED Mod, Security Mod, Dual NUB, Mode Select Switch + More

Offline ReZiN_420

  • Chief squatting Hard
  • *
  • Posts: 17
  • Post quality +0/-0
  • Gender: Male
  • Moding is not a hobby, it's a habit
Re: Ground Pin?
« Reply #6 on: July 11, 2008, 05:11:45 PM »
Ok thankx bro, i thought u were give me the cold shoulder and being a :censored: but i relize you must be quiet busy. So i apologize for my quick assumptions.
Logged

Offline Sanctus

  • Acid Modder
  • *
  • Posts: 606
  • Post quality +1/-0
  • Gender: Male
Re: Ground Pin?
« Reply #7 on: July 11, 2008, 06:29:17 PM »
So is that the correct pins then? Also I can't find that pic :S
Logged

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: Ground Pin?
« Reply #8 on: July 12, 2008, 07:01:40 AM »
Quote from: Sanctus on July 11, 2008, 06:29:17 PM
So is that the correct pins then? Also I can't find that pic :S

Yes that is the correct wire, unfortunatly i don't have timmy's pic but i'm sure someone here does. keep searching. :)
Logged

Offline ReZiN_420

  • Chief squatting Hard
  • *
  • Posts: 17
  • Post quality +0/-0
  • Gender: Male
  • Moding is not a hobby, it's a habit
Re: Ground Pin?
« Reply #9 on: July 16, 2008, 01:12:58 AM »
Alright dudes, every thing went just about well, the pic above that I took was correct so use if needed, thankx goes out to Aphex, nico and all of acid mods :drunk:! As for my slim dual nub it is on the outside, because I intend to buy a new casing whenever they actually come out with a full installation tut :dntknw:, because i have no idea where your supposed to put the power board and what not(in short, no under the faceplate for now). Ok heres the pics of what i got....





Couple last things, my cross(X) button doesn't seem to work when I screw it all back together but works fine when its all opened up...so im guessing its an issue with placement, I cut the rubber back of it a little but still nothing. Also, I placed my razor touching the plastic case of the nub, which I found(after a bit of research) to be to close theres the pic at the bottem, to get it to work i have to put my finger on the bottom push the joystick up and play with it a little and then all 4 directions work fine. So how far should i put it? Any advice for my 2 problems? Thankx in advance.
« Last Edit: July 16, 2008, 01:18:13 AM by ReZiN_420 »
Logged

Offline Sanctus

  • Acid Modder
  • *
  • Posts: 606
  • Post quality +1/-0
  • Gender: Male
Re: Ground Pin?
« Reply #10 on: July 16, 2008, 03:28:02 AM »
Looks good. Love the color scheme on your psp to  :tup: I'm planning to do this mod hopefully. Do you reckon if you squeeze it in there that theres enough room to keep the power board in there and have the nub(all internally)?

EDIT:alright im trying to do this but i cant get the wire to go on the pins on the mobo as soon as I get them soldered and i go on to do my next wire is comes off >.> any suggestions?
« Last Edit: July 16, 2008, 07:31:24 PM by Sanctus »
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal