Author Topic: Modding injuries? (Read 4730 times)

H-Sauce · « **on:** August 11, 2009, 05:10:25 AM »

What ones have you had, if any?

I was just having a look at my xbox, I ran it out of the case (stupid idea I know) and nothing was happening. So as I checked to see if the cable wasd in I ended with 240V running through me.

budgray19 · « **Reply #1 on:** August 11, 2009, 05:15:07 AM »

well its not 1 i have but its 1 u can very easly get
cancer
dont be sniffinin the fumes of older style solder and teh flux fumes
make sure u wash ur hands very good after handling

PhenomenalDesigns · « **Reply #2 on:** August 11, 2009, 05:59:01 AM »

My arms and hands are covered in scars because of modding, my most recent is a patch of light skin (scar) on my finger because i burnt it with a butane torch

alentris · « **Reply #3 on:** August 11, 2009, 08:04:17 AM »

I reached for my dremel once, and ended up grabbing the tip of my soldering iron

. Probably one of the most painful happenings in my life.

gamerdude767 · « **Reply #4 on:** August 11, 2009, 08:27:17 AM »

i accidentally dropped my soldering iron onto my leg and it burn 4mm into my skin.. i had to get it patched and stitched up

Jumbo · « **Reply #5 on:** August 11, 2009, 09:05:51 AM »

One of the worst is i grabbed the wrong end of my soldering iron... Good thing i only grab it with 2 fingers. 850*f isn't very comfortable and its so hot you dont react quick enough o just drop it you yell then drop it lol.

but a couple months ago when i was modding daily i would burn myself every other hour because i am tinning things while holding it. Its REALLY not that bad.

I almost cut my finger in half with a table saw. I was ripping a piece of ply wood and my mom was screaming at me to get inside and i turned around and my finger rubbed the side of the blade. 2 mm over and my hand was F'ed. Most of my injuries are from working construction. I dropped a 700 LB slab of concrete on my foot once too i had a swollen foot and couldnt walk for a a week.

treemty · « **Reply #6 on:** August 11, 2009, 09:45:12 AM »

burned myself countless times wih soldering irons, im used to it now. but once i thought I could use it like a pencil, and ended up burning my knuckle =D

besides that, I have accidently sandeed my fingers from dremel slips, had plexiglass in my eye and droped blobs of solder on bare feet

alentris · « **Reply #7 on:** August 11, 2009, 09:53:54 AM »

Quote from: treemty on August 11, 2009, 09:45:12 AM

burned myself countless times wih soldering irons, im used to it now. but once i thought I could use it like a pencil, and ended up burning my knuckle =D

besides that, I have accidently sandeed my fingers from dremel slips, had plexiglass in my eye and droped blobs of solder on bare feet

I accidentally dremeled a hole in my fingernail once

... I've also gotten stabbed by my screwdriver, cut by a box cutter, and dropped a little bit of of molten solder on my thigh...

aZiZ1 · « **Reply #8 on:** August 11, 2009, 10:09:24 AM »

Slit my wrist on mr.El-cheapo computer case... Noone told me they were that sharp ><. and since ive been depressed all around my parents thought i tried to kill myself. Hospital and back i am under 24hr surveillance.

budgray19 · « **Reply #9 on:** August 11, 2009, 10:11:36 AM »

this isnt a injery but something funny
i was using a buffing wheel on my dremel and i wasnt paying attention and my underwear i was wearing got caught up in it and wraped around it also with a bit of my... but it stoped before i had a curly Q
lets carry on shall we

aZiZ1 · « **Reply #10 on:** August 11, 2009, 10:15:32 AM »

LLLLLOOOOOOLLLLLLLLLL budgray i love u

802Chives · « **Reply #11 on:** August 11, 2009, 10:28:55 AM »

wasnt modding but I was assembling circuit boards one time with very fine tweezers, and I dropped them. As usual when you drop something in your lap, I quickly closed my legs to catch em and ended up stabbing the tweezers into my leg about 3/4" deep. ouch, puncture wounds dont hurt right off, but they ache for days after.

I burn my finger on a 750F iron at least once a week, and cant make a full day in the machine shop without some sort of cut on my hands

Modded Matt · « **Reply #12 on:** August 11, 2009, 12:58:38 PM »

when I get ready to assemble a chip for a controller I basically know how long the wires will need to be so before I start, I precut the size and color wires I need, so I acn just assemble the socket, mount and conect the precut wires. part of my prep process is to tin all of my wires. well I line them up in me helping hands vice and apply an nice amount of solder to the tip of the iron and just rub the iron accross the wire, I was moving kinda fast and I kinda flicked one of the wires with the iron and took a small bit of melted solder to the eyeball. it hurt for a week. you can still see where it hit the eye.

Jumbo · « **Reply #13 on:** August 11, 2009, 01:10:44 PM »

Holy

chives. I should be more careful now. OW. I would rage hard if that happened to me.

H-Sauce · « **Reply #14 on:** August 11, 2009, 01:38:35 PM »

I burn my self 50% of the time I use my iron, mainly because I never really use my stand lol.

I don't know if it was caused by what happened earlier, but at about 7:00 PM I was having extremely bad stomach pains. So bad i was down on all fours trying to stop the pain. About 5 minutes later my parents see and give me ibuprofen. I went into the living room and I vomited mostly water then fell asleep. I just woke up lol.

treemty · « **Reply #15 on:** August 11, 2009, 01:40:03 PM »

Quote from: H-Sauce on August 11, 2009, 01:38:35 PM

I burn my self 50% of the time I use my iron, mainly because I never really use my stand lol.

I don't know if it was caused by what happened earlier, but at about 7:00 PM I was having extremely bad stomach pains. So bad i was down on all fours trying to stop the pain. About 5 minutes later my parents see and give me ibuprofen. I went into the living room and I vomited mostly water then fell asleep. I just woke up lol.

DUDE!
that happened to me a few weeks ago, did it feel like sharp pains?

P3nnyw1se · « **Reply #16 on:** August 11, 2009, 02:35:51 PM »

I burned my finger while I was chipping my Ps2 yesterday! It's not that bad though, but it hurt for a bit, x.x

H-Sauce · « **Reply #17 on:** August 11, 2009, 02:59:40 PM »

Quote from: treemty on August 11, 2009, 01:40:03 PM

DUDE!
that happened to me a few weeks ago, did it feel like sharp pains?

It was like a sharp pain, but 1 that just lasted for about 30 minutes.

Blazinkaos · « **Reply #18 on:** August 11, 2009, 08:55:37 PM »

Well were should i start i cut my several times with a xato knife, burned my self with the soldering iron, dropped hot solder on my pants and went through my pants on my leg that really sucked cuz i had a hard time getting them off.... ummm cut my self with the dremel bleed quite a bit from that, hit in the eye by a spring, and i think thats all i remember.

scott · « **Reply #19 on:** August 14, 2009, 09:45:49 AM »

Solder drops on the legs really sucks, because they dont come off until they cool.

I have fried all my finger tips off and cant really feel anything with them anymore.

I have in haled more kinds of fumes than i can count

The dremel hates me.

Dont even get me started on my letter opener.

H-Sauce · « **Reply #20 on:** August 14, 2009, 10:22:59 AM »

Ok, I didn't realise how axccident prone we all are lol.

bustinthejustin · « **Reply #21 on:** August 14, 2009, 12:03:28 PM »

Well when you put a bunch of teenagers with things like rotary tools, xacto knives, hot irons, solder, solder fumes, etc... you're gonna end up with a lot of accidents XD

Be careful kids. Modding is a serious business.

Modded Matt · « **Reply #22 on:** August 14, 2009, 12:15:59 PM »

Quote from: bustinthejustin on August 14, 2009, 12:03:28 PM

Well when you put a bunch of teenagers with things like rotary tools, xacto knives, hot irons, solder, solder fumes, etc... you're gonna end up with a lot of accidents XD

Be careful kids. Modding is a serious business.

LOL adults as well

Slim Hacker · « **Reply #23 on:** August 14, 2009, 12:41:23 PM »

Who was it that took solder to the jewels? wasnt it nico?

Bhawan · « **Reply #24 on:** August 14, 2009, 12:46:55 PM »

one time, i was working on some school project and had all my setup on the floor (totally stupid but i had no other place no table no nothing) and heres the worst part, i stepped on the soldering iron... rest is understood. i have burnt myself countless times while soldering...

Blazinkaos · « **Reply #25 on:** August 15, 2009, 10:03:52 AM »

Quote from: bustinthejustin on August 14, 2009, 12:03:28 PM

Well when you put a bunch of teenagers with things like rotary tools, xacto knives, hot irons, solder, solder fumes, etc... you're gonna end up with a lot of accidents XD

Be careful kids. Modding is a serious business.

Im turning 21 here soon -_-!

Rory · « **Reply #26 on:** August 20, 2009, 01:20:57 PM »

I burnt mah pen0r wit mah soldering iron b4 lulz.

News:

Author Topic: Modding injuries? (Read 4730 times)