Author Topic: Rapid Fire Problem  (Read 1654 times)

Offline stunnedjack2

  • Chief squatting Hard
  • *
  • Posts: 11
  • Post quality +3/-1
  • Acidmods User
Rapid Fire Problem
« on: April 22, 2011, 01:33:01 PM »
So I installed a rapid fire chip into a wired controller and the player 4 led is not showing up, this is the second time its done that(put a diff chip into another controller). But the rapid fire works(tested on mw2) but the light wont come on, ive also installed the same chip into a wireless controller and it works fine. Is there something with the wired controllers, thats messed up

Also the controller randomly shoots 1 shot every 3 mins or so.

Thanks if u can help

I installed it exactly like the instructions said to but the led's not working






Offline Dcofer

  • Ω Allumnist Ω
  • *
  • Posts: 118
  • Post quality +1/-1
  • Gender: Male
  • Acidmods User
Re: Rapid Fire Problem
« Reply #1 on: April 22, 2011, 10:49:27 PM »
dunno about the random fire, but maybe the P4 led got toasted during soldering.  If you haven't checked that that might be a good place to start. I know there are some changed between the wired and wireless controllers but I'm sure you followed the wired pcb diagram.


Xbox 360 gamertag: EMERGENCY DODO
PS3 gamertag: Emergency_Dodo

Offline crazy-modder

  • Research & Development
  • Acid Modder
  • *
  • Posts: 854
  • Post quality +34/-2
  • Gender: Male
Re: Rapid Fire Problem
« Reply #2 on: April 22, 2011, 10:55:11 PM »
uhhh what code are you using on that chip? I haven't seen any chips from this site wired like that

Offline stunnedjack2

  • Chief squatting Hard
  • *
  • Posts: 11
  • Post quality +3/-1
  • Acidmods User
Re: Rapid Fire Problem
« Reply #3 on: May 31, 2011, 03:04:39 PM »
iis a chip i bought from another website. and i asked the guy and he realy has no clue what hes talking about.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Rapid Fire Problem
« Reply #4 on: May 31, 2011, 04:10:05 PM »
hahahahhahaha..... sorry, the guy you bought it from didnt know what he was talking about?

the wiring is equal to gameplayrf with right trigger/button only. (assuming the chip is turned top down deadbug.)

but, I have never modded a wired controller, I am sure there are considerable differences, but my fist thought would be that there is no resistor on the led so it is probably fried, unhook it and see if the led works without the chip attached.
« Last Edit: May 31, 2011, 04:11:35 PM by modded matt »

Offline Hazer

  • x4675636B4E7574
  • Acidmods Alumni
  • Acid Modder
  • *
  • Posts: 583
  • Post quality +59/-0
Re: Rapid Fire Problem
« Reply #5 on: May 31, 2011, 05:29:46 PM »
So I checked the X-S forums for LED layouts on wired controllers. This one does not match the old wired matrix or CG. I have a feeling you wired it to the correct end of the LED. But I also see you do not have a resistor for the LED. The wired controllers use 5V power, where the wireless use 3V. The LED probably got burnt the very first time you plugged it in.
[Quote from Gamermodz via Viking forums]
Don't be jealous your not half as smart. I hate ****tards like you. An ignorant redneck. Your nothing but a posing ******. Get the **** out of here, really, your claim to fame is an open source rapid fire code? You make me laugh. You think you have control over the modding market?  You couldn't create what I can and do. You are too ignorant with your outrageous assumptions and accusations. [/Quote]

Offline stunnedjack2

  • Chief squatting Hard
  • *
  • Posts: 11
  • Post quality +3/-1
  • Acidmods User
Re: Rapid Fire Problem
« Reply #6 on: June 14, 2011, 10:36:17 PM »
hahahahhahaha..... sorry, the guy you bought it from didnt know what he was talking about?

the wiring is equal to gameplayrf with right trigger/button only. (assuming the chip is turned top down deadbug.)

but, I have never modded a wired controller, I am sure there are considerable differences, but my fist thought would be that there is no resistor on the led so it is probably fried, unhook it and see if the led works without the chip attached.

Ya like he said that it its fine and said the swap the wires, and he didnt know what i was talking about. but ya I kinda gave up on the wired controller.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal