« previous next »
Pages: [1]   Go Down

Author Topic: Just bought the pickit3 and need help?  (Read 3465 times)

Offline Bayrepairs

  • Chief squatting Hard
  • *
  • Posts: 12
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Just bought the pickit3 and need help?
« on: March 19, 2010, 09:07:54 AM »
OK so i bought the pickit3 to mod controllers etc.

now i have been explained that i do not need the board it came with so what do i need?

i got the pickit3 and the pic ready
Logged

Offline t0pP8uZz

  • Granny Spanker
  • *
  • Posts: 477
  • Post quality +4/-0
  • Gender: Male
  • Programmer / Security Expert
    • http://milw0rm.com/author/1141
Re: Just bought the pickit3 and need help?
« Reply #1 on: March 20, 2010, 07:21:12 AM »
That board it comes with is for debugging.

There are tons of extra headerboards for each device that can be used for debugging, Only if the PIC doesnt have internal circuitry for debugging.(not many have) But since your not debugging. Your just programming, you dont have to worry about any of that.

You really need to do some reading. Its very easy. Program using ICSP.

PicKit3 operates the same way as pickit2, There are 6 pins. With the programmer faceup and the pins facing towards yourself. the pins are numbered from left to right. Ill explain the pins below.

PIN 1 - MCLR / Vpp (programming voltage. normally 13v) connect to PIC's MCLR pin, and causes the pic to enter programming mode
PIN 2 - Vdd - Powers the PIC. you may use a diffrent powersupply (normally 3.3v-5v)
PIN 3 - Ground - Connect to PIC's GND/Vss
PIN 4 - DATA - This connects to the PIC's Data pin or DAT
PIN 5 - CLOCK - Connects to PIC's CLK/CLOCK pin
PIN 6 - LVP - Low volage programming, were not using LVP so leave it alone

Okay so now.. grab yourself a pic socket. goto microchip and find the data sheet for the device you want to program.. read teh PIN DIAGRAM section, and it will tell you cleary which PINS on the PIC are which. then just connect the wires accroding to the pickit3.

For more information check: http://ww1.microchip.com/downloads/en/DeviceDoc/PICkit_3_User_Guide_51795A.pdf

Dont let it scare you, Read it thoughly.
Logged

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: Just bought the pickit3 and need help?
« Reply #2 on: March 22, 2010, 06:08:56 PM »
Hmm about making the adapter thing... Do you just straight-up connect the corresponding pins from the socket onto your header to plug into the pickit? Or is there something else you need to do?
Logged

Sig by Kenshinffx - Thanks!

Offline Bayrepairs

  • Chief squatting Hard
  • *
  • Posts: 12
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Just bought the pickit3 and need help?
« Reply #3 on: March 22, 2010, 11:04:34 PM »
i would like to know because i got chip and pic but don't know how to program
Logged

Offline GhoSt

  • Creating Null
  • Around the block
  • *
  • Posts: 2552
  • Post quality +19/-0
  • Gender: Male
  • Null Pointer Exception
Re: Just bought the pickit3 and need help?
« Reply #4 on: March 22, 2010, 11:40:12 PM »
yes you connect the header pins directly to the corresponding pic pins, no components needed.
Logged
|Variegation - GhoSt's Final Controller|

|Nothing is deterministic.|

Offline Bayrepairs

  • Chief squatting Hard
  • *
  • Posts: 12
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: Just bought the pickit3 and need help?
« Reply #5 on: March 25, 2010, 07:22:40 AM »
ok so i put the pickit3 in and installed the cd .

open mlab but when i go to program it says i don't have it connected is there something else i have to buy besides the pickit3 and the pic
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal