Old school back with a 360 slim. Lost touch with mods and flash need help

[The End of A Heartache]

no i put that there because its important and i was just making sure the point was getting across. nothing you did my friend. lol
you had it booting stock nand correct?
if so when you installed everything back in did you change any of the resistor for the nand read write.

Yeah it booted with stock nand and no the resistor are still there. Nothing changed other than the dgx install lol

I just changed the blue cable for a longer blue cable but still red ring. Hmmm well last thing to do is flash DGX to RGX and try again.

[Gizmo613]

hold the sync button and press eject 4x times for the error code.

[The End of A Heartache]

hold the sync button and press eject 4x times for the error code.

Well I flashed the DGX to RGX and no more red ring it works thank you gizmo

 but I got an issue no activation light on the new RGX

I see the RED power light is very dime :/

the power required for the RGX is 5v which I have solder to the tap on the QSB CR upgrade but I do not think I am getting 5volt to the RGX

I don't have a multimeter with me to check but I am going to redo the solder point I had some cold solder problem last time so I am going to go over the joints one more time.

[Gizmo613]

use flux, some of your points are pretty dry.

[The End of A Heartache]

use flux, some of your points are pretty dry.

Hmmm i got a nice ball joint between the board and the QSB tried one more time still got a dime red light only. Fan is going uber fast also not sure if thats because of the RGX flashing.

Anyways hmm :/ not sure what to do next not getting any

maybe I should desolder jump 1 and try jump2?

I have a bridge on jump 3 as well from factory not sure if that might be the problem?

[Gizmo613]

by the way, which corona rgx did you flash to the dgx?

also desolder the jumper you had solder. but leave the factory bridge alone

[The End of A Heartache]

by the way, which corona rgx did you flash to the dgx?

also desolder the jumper you had solder. but leave the factory bridge alone

I did the cor_C

and okie I'll desolder the bridge on jumper 1

[Gizmo613]

ummm, did you solder your ground wire? the pictures you have doesnt show them soldered to anything.

[The End of A Heartache]

ummm, did you solder your ground wire? the pictures you have doesnt show them soldered to anything.

can't really solder it since it will not hold well. As soon as the ball cools it pops off the case which is why I have to tape it down its the only way. I might have to strip more of the shielding off to get a better contact.

Oh your right Now Im getting activity thanks gizmo

[Gizmo613]

LOL!!!

well desoler jumper 1 and leave jumper 3 as is. that should be your default setting. connect the comport cable and start monitoring under jrunner. hopefully you get your cpu key!

here comes the fun part! wire length and cap tuning here is what makes the difference.

[The End of A Heartache]

LOL!!!

well desoler jumper 1 and leave jumper 3 as is. that should be your default setting. connect the comport cable and start monitoring under jrunner. hopefully you get your cpu key!

here comes the fun part! wire length and cap tuning here is what makes the difference.

well i still don't have a boot  getting the same 1 blink activation that I was having with coolrunner so I guess the "fun" part is next on the list lmao

[Gizmo613]

1 blink?
 can you give me a estimate of your wire lengths? specifically the cpu-rst wire and post out.

[The End of A Heartache]

1 blink?
 can you give me a estimate of your wire lengths? specifically the cpu-rst wire and post out.

10 inches I swapped the 10cm for a longer one because of the not booting issue. I guess I need to go back to 10cm cable

[Gizmo613]

what about the yellow post out?

[The End of A Heartache]

what about the yellow post out?

10cm yellow

 i swapped out the blue 10cm gonna try again

[Gizmo613]

try 10 cm blue for cpu and 12 cm for yellow post out.

[The End of A Heartache]

try 10 cm blue for cpu and 12 cm for yellow post out.

still can not get xell to boot might have to use capacitor :/

[Gizmo613]

how long did you wait?

when you are using the caps, start with 10pf and work your way up to 47pf. cor_c only goes that high in caps. 68pf or higher will damage the rgx.

[Rodent]

still can not get xell to boot might have to use capacitor :/

its a rgh2 its a corona it will take longer to boot then any normal rgh2 console  that is why people do not want corona's

[The End of A Heartache]

how long did you wait?

when you are using the caps, start with 10pf and work your way up to 47pf. cor_c only goes that high in caps. 68pf or higher will damage the rgx.

I waited about 12 minute or a little longer

Okie so need to look for 10pf and move my way up to 47pf will do tomorrow thanks gizmo for the heads up on the limit.

I think I will bridge jump 1 and try again then call it a night and do the cap's tomorrow.

its a rgh2 its a corona it will take longer to boot then any normal rgh2 console  that is why people do not want corona's

lol working with DGX and yeah its getting to a point that I am not wanting to mess with it any more.

[Rodent]

I waited about 12 minute or a little longer

Okie so need to look for 10pf and move my way up to 47pf will do tomorrow thanks gizmo for the heads up on the limit.

I think I will bridge jump 1 and try again then call it a night and do the cap's tomorrow.

lol working with DGX and yeah its getting to a point that I am not wanting to mess with it any more.

  Flash back the orignal nand. and be done with it , shouldnt of took  this long to rgh it. i could of made you one cheaper in the long run in the amount of time wasted here but at least you learned something while trying to improve your modding skills    

[The End of A Heartache]

  Flash back the orignal nand. and be done with it , shouldnt of took  this long to rgh it. i could of made you one cheaper in the long run in the amount of time wasted here but at least you learned something while trying to improve your modding skills    

lol ill try one last time to get the key out and if it doesn't work then I am flashing back the NAND and working on the mod on the shell haha

and yes as long as I learn things its not really a waste thanks guys for the help both of you.