Author Topic: I just made a Nintendo Screwdriver (Read 43397 times)

F00 f00 · « **on:** January 21, 2007, 09:30:21 AM »

Yay me!

Now I can overclock my N64. Get in!

User · « **Reply #1 on:** January 21, 2007, 10:58:43 AM »

w00t.

HoffmanMyster · « **Reply #2 on:** January 21, 2007, 02:56:31 PM »

Quote from: F00 f00 (R&D-Q&A) on January 21, 2007, 09:30:21 AM

Yay me!
Now I can overclock my N64. Get in!

dam, seems youre having more luck or skill whichever one, mine just wont turn the gamecube screws...but theyre so far in I cant see whats wrong, maybe Ill try it with my n64.

F00 f00 · « **Reply #3 on:** January 21, 2007, 05:13:54 PM »

Quote from: HoffmanMyster on January 21, 2007, 02:56:31 PM

dam, seems youre having more luck or skill whichever one, mine just wont turn the gamecube screws...but theyre so far in I cant see whats wrong, maybe Ill try it with my n64.

It wasnt to bad. I just had a go at it and got one screw out after a bit of a struggle. Then used that screw to get it perfect. I'll mesure it out if that helps

HoffmanMyster · « **Reply #4 on:** January 21, 2007, 05:24:24 PM »

Quote from: F00 f00 (R&D-Q&A) on January 21, 2007, 05:13:54 PM

It wasnt to bad. I just had a go at it and got one screw out after a bit of a struggle. Then used that screw to get it perfect. I'll mesure it out if that helps

ok, and I think my problem is that the groove isnt deep enough into the head...I think its wide enough, cause its 3 cds thick, which is the suggested thickness, and I can really go that much wider, but Ill try making it deeper, see if that helps, not sure when Ill be able to do that though,...but please do measure it too, Ill see if thats the problem before I dremel more out.

F00 f00 · « **Reply #5 on:** January 22, 2007, 11:37:16 AM »

Quote from: HoffmanMyster on January 21, 2007, 05:24:24 PM

ok, and I think my problem is that the groove isnt deep enough into the head...I think its wide enough, cause its 3 cds thick, which is the suggested thickness, and I can really go that much wider, but Ill try making it deeper, see if that helps, not sure when Ill be able to do that though,...but please do measure it too, Ill see if thats the problem before I dremel more out.

Just checked mine and it is 3 cds wide. Its about 4mm deep. I also made tapered it to the tip, so its quite sharp. Let me know how you get on.

HoffmanMyster · « **Reply #6 on:** January 23, 2007, 10:41:24 AM »

Quote from: F00 f00 (R&D-Q&A) on January 22, 2007, 11:37:16 AM

Just checked mine and it is 3 cds wide. Its about 4mm deep. I also made tapered it to the tip, so its quite sharp. Let me know how you get on.

Alright, Ill check when I get home, and do you have any idea how to make triwing drivers for opening the sp?

F00 f00 · « **Reply #7 on:** January 23, 2007, 10:56:55 AM »

Quote from: HoffmanMyster on January 23, 2007, 10:41:24 AM

Alright, Ill check when I get home, and do you have any idea how to make triwing drivers for opening the sp?

Funny you should say that, I've been thinking about giving it a go. I guess we could just cut the top of a normal driver and just cut the shape into it.

HoffmanMyster · « **Reply #8 on:** January 23, 2007, 06:56:41 PM »

Quote from: F00 f00 (R&D-Q&A) on January 23, 2007, 10:56:55 AM

Funny you should say that, I've been thinking about giving it a go. I guess we could just cut the top of a normal driver and just cut the shape into it.

Hmm....thats true, but thatd be some fine and precise filing or whatever form we use to do that...and as for the gamecube screwdriver, mine is just a bit too big, so Ill probably use that one if I decide to make a SP one, since you cant un-dremel...dam, I wish there was undo in real life....

Its13oclock · « **Reply #9 on:** January 24, 2007, 08:00:00 PM »

nice. its better than what i did. I melted the tip of a pen and made a "mold" of the screw, and let it harden up. Then I used that.

HoffmanMyster · « **Reply #10 on:** January 26, 2007, 10:21:24 AM »

Quote from: Its13oclock on January 24, 2007, 08:00:00 PM

nice. its better than what i did. I melted the tip of a pen and made a "mold" of the screw, and let it harden up. Then I used that.

Yeah, thats what I may have to end up doing....I dont have one readily available, but what do the NES screws look like?

F00 f00 · « **Reply #11 on:** January 26, 2007, 10:56:11 AM »

I dont remember the nes screws I havent go one heree to check, but I think there the same as the snes.

Dose that pen trick work? I didnt think it would so I never even tried.

TR4G- · « **Reply #12 on:** January 26, 2007, 02:45:50 PM »

Quote from: F00 f00 (R&D-Q&A) on January 26, 2007, 10:56:11 AM

I dont remember the nes screws I havent go one heree to check, but I think there the same as the snes.

Dose that pen trick work? I didnt think it would so I never even tried.

and how exactly did u get the screws off ur Gameboy? cuase of the stupid 3 pronged screws.....

F00 f00 · « **Reply #13 on:** January 26, 2007, 03:00:30 PM »

I just used a small flathead and will power. It seemed to take about 2 hours.

TR4G- · « **Reply #14 on:** January 26, 2007, 03:15:42 PM »

Quote from: F00 f00 (R&D-Q&A) on January 26, 2007, 03:00:30 PM

I just used a small flathead and will power. It seemed to take about 2 hours.

lol, ok as long as its possible........cuase i tryed for like 2 minutes and gave up lol

pinoyballa · « **Reply #15 on:** January 27, 2007, 09:45:16 AM »

or you could order a screwdriver of of nds-central or one of their resale sites for only like 3 bucks

Its13oclock · « **Reply #16 on:** January 27, 2007, 06:08:27 PM »

c'mon now. if you cant open it, then it aint yours, lol. thats a motto i like from makezine

Kaito · « **Reply #17 on:** January 27, 2007, 08:36:48 PM »

try to make a screwdriver for the gameboy color .. the screws looks like this
|
/ \

F00 f00 · « **Reply #18 on:** January 28, 2007, 03:49:55 AM »

I am on it.

dedafmonteur · « **Reply #19 on:** January 28, 2007, 04:07:19 AM »

Quote from: Jakzun on January 27, 2007, 08:36:48 PM

try to make a screwdriver for the gameboy color .. the screws looks like this
|
/ \

or just buy them

F00 f00 · « **Reply #20 on:** January 28, 2007, 04:18:27 AM »

Dude, the whole point is to make your own stuff.

Kaito · « **Reply #21 on:** January 28, 2007, 08:03:30 PM »

Quote from: dedafmonteur on January 28, 2007, 04:07:19 AM

or just buy them

from where ?

F00 f00 · « **Reply #22 on:** January 29, 2007, 03:56:47 AM »

We'll I made one. Its not pretty but ti dose work. You can get them on ebay I think.

pinoyballa · « **Reply #23 on:** February 03, 2007, 06:50:42 PM »

or the e store

F00 f00 · « **Reply #24 on:** February 03, 2007, 06:55:17 PM »

Yeah, I know. That post was before the new estore was up.

Ilzwalrus · « **Reply #25 on:** February 03, 2007, 09:51:12 PM »

Hey which consoles is this screwdriver for?

F00 f00 · « **Reply #26 on:** February 04, 2007, 06:43:35 AM »

I made the first one for my N64, and the second for my gb. The first is on most nintendo consoles, the second is on most of the nintendo handhelds.

Ilzwalrus · « **Reply #27 on:** February 04, 2007, 11:12:29 PM »

Ah, right.

I used a flathead to unscrew the gameboy. The first time it was bloody impossible. Took so long. Now they're pretty loose and so it's really easy to unscrew.

User · « **Reply #28 on:** February 11, 2007, 10:33:01 AM »

Quote from: F00 f00 on January 28, 2007, 04:18:27 AM

Dude, the whole point is to make your own stuff.

It's called Acid Mods not Acid Buys.

billy23 · « **Reply #29 on:** February 15, 2007, 09:07:38 PM »

time to start grinding down a screw driver

News:

Author Topic: I just made a Nintendo Screwdriver (Read 43397 times)