« previous next »
Pages: [1]   Go Down

Author Topic: shorting out psp slim power fuse easy way  (Read 9666 times)

Offline vladstir

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 70
  • Post quality +0/-0
shorting out psp slim power fuse easy way
« on: November 05, 2008, 08:34:16 AM »
I bought a broken psp slim online, and i want to try to fix it. the previous owner tryed to short out the power fuse and did a bad job doing so. I read on this site that you just put solder over the fuse but is there an easier way to do so like a jumper wire?





Is this even worth fixing?
Logged

Offline socomhacker239

  • E = MC²
  • *
  • Posts: 327
  • Post quality +0/-0
  • Gender: Male
Re: shorting out psp slim power fuse easy way
« Reply #1 on: November 05, 2008, 01:09:03 PM »
solder is the easyest way to bridge the fuse is it worth fixing? yes!
Logged

Offline j.s2ghetto

  • Millennium Poster
  • *
  • Posts: 1001
  • Post quality +0/-0
  • Gender: Male
  • GHETTO inside
Re: shorting out psp slim power fuse easy way
« Reply #2 on: November 05, 2008, 01:16:07 PM »
Y wouldn't it be
try if it don't work wat do u loss NOTHING
Logged

thank u P3nnywise for the sig
"See you have to understand the difference. The difference between me and you is to you, this is your job. To me, this is my life. The club; that's my job. The mall; that's my job. Your neighborhood; that's my job. This studio; this is my life. This is what I do better than anything."

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: shorting out psp slim power fuse easy way
« Reply #3 on: November 05, 2008, 01:34:28 PM »
What did you do to the poor thing??

I would clean that up with some flux remover and try again with not that much flux
Logged

Offline ProperBritish

  • Acid Modder
  • *
  • Posts: 856
  • Post quality +0/-0
  • Gender: Male
  • Raining Blood! From A Lacerated Sky!
Re: shorting out psp slim power fuse easy way
« Reply #4 on: November 05, 2008, 01:46:40 PM »
damna a flux bomb went off there.

remove the flux, clean it up, bridge the connection CAREFULLY
Logged


Quote from: ≤Ʀαωгу≥
you know who i would bone? daffy duck

Offline LaCozTe-2028

  • BANNED
  • E = MC²
  • *
  • Posts: 353
  • Post quality +0/-0
  • Gender: Male
  • I love My Lacoste shirts
Re: shorting out psp slim power fuse easy way
« Reply #5 on: November 05, 2008, 06:46:29 PM »
Yup he also burnt his switch thats no to good dude watch out
Logged

Quote from: LaCozTe-2028 on October 11, 2008, 11:57:06 AM
try droping it again
my retared friend fixed by droping it
 1Sniper- not to be an :censored: but, its special friend

Offline PspKicks316

  • Acidmods Alumni
  • Mad Bomber
  • *
  • Posts: 5709
  • Post quality +5/-4
  • Gender: Male
Re: shorting out psp slim power fuse easy way
« Reply #6 on: November 05, 2008, 08:22:17 PM »
Guys, please read first before going all wtf did you do on someone.
He bought it online like this.

Do what everyone else said, clean up the board a bit and all you need to do is solder over the fuse. Using a jumper wire is actually a harder way of doing it.
Logged

Offline LaCozTe-2028

  • BANNED
  • E = MC²
  • *
  • Posts: 353
  • Post quality +0/-0
  • Gender: Male
  • I love My Lacoste shirts
Re: shorting out psp slim power fuse easy way
« Reply #7 on: November 06, 2008, 03:31:24 PM »
Why would someone want to short a mobo
Logged

Quote from: LaCozTe-2028 on October 11, 2008, 11:57:06 AM
try droping it again
my retared friend fixed by droping it
 1Sniper- not to be an :censored: but, its special friend

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: shorting out psp slim power fuse easy way
« Reply #8 on: November 08, 2008, 06:36:27 AM »
Way to much damage to be repaired.

And secondly, There is no flux at all there.
« Last Edit: November 08, 2008, 06:57:19 AM by Alien_X »
Logged

Sigs by Alien_X
www.ax-elec.com

Offline LaCozTe-2028

  • BANNED
  • E = MC²
  • *
  • Posts: 353
  • Post quality +0/-0
  • Gender: Male
  • I love My Lacoste shirts
Re: shorting out psp slim power fuse easy way
« Reply #9 on: November 08, 2008, 08:03:24 AM »
yup its burnt mobo and plastic from teh umd sensor
Logged

Quote from: LaCozTe-2028 on October 11, 2008, 11:57:06 AM
try droping it again
my retared friend fixed by droping it
 1Sniper- not to be an :censored: but, its special friend

Offline PspKicks316

  • Acidmods Alumni
  • Mad Bomber
  • *
  • Posts: 5709
  • Post quality +5/-4
  • Gender: Male
Re: shorting out psp slim power fuse easy way
« Reply #10 on: November 08, 2008, 10:08:58 AM »
He's not talking about shorting the psp, guys read.
He was asking how to bridge the fuse the easy way, he just used to wrong terminology.
You guys need to read before saying something.
Quote from: Alien_X on November 08, 2008, 06:36:27 AM
Way to much damage to be repaired.

And secondly, There is no flux at all there.
Really? I couldn't tell whether it was a bit of flux or just burnt mobo in that third pic. If that's burnt, damn what the hell was the original owner doing to that thing? Blow torching it?! :taunt:
« Last Edit: November 08, 2008, 10:49:27 AM by PspKicks316 »
Logged

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: shorting out psp slim power fuse easy way
« Reply #11 on: November 08, 2008, 10:12:41 AM »
Yup

The Burnt laminate is peeling away from the FR4 base.
Not flux, just singed circuit board.

But still, you don't necessarily have to bridge those two points, I know some other points you can connect to bypass the fuse.
But I think the umd switch will be a problem.
Logged

Sigs by Alien_X
www.ax-elec.com
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal