Author Topic: UMD DOOR SO PERFECT!  (Read 2413 times)

Thanks48

  • Guest
UMD DOOR SO PERFECT!
« on: December 14, 2008, 07:04:57 AM »
How are yah cutting out the umd doors so perfect and round would like a tutorial of how to do it please! ... Thanks

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: UMD DOOR SO PERFECT!
« Reply #1 on: December 14, 2008, 10:37:40 AM »
https://www.acidmods.com/forum/index.php?topic=25713.0


Read my response. It's far from being a good tutorial, but it's a general idea of what to do.

Sig by Kenshinffx - Thanks!

Thanks48

  • Guest
Re: UMD DOOR SO PERFECT!
« Reply #2 on: December 14, 2008, 11:04:59 AM »
thanks :clap:

Offline ryan0

  • I EAT STUFF
  • Millennium Poster
  • *
  • Posts: 1128
  • Post quality +0/-0
  • Gender: Male
  • I LIEK CHEEEEZE
Re: UMD DOOR SO PERFECT!
« Reply #3 on: December 22, 2008, 01:49:41 PM »
I use a milling machine and a jig for cutting umd doors.
Derp.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: UMD DOOR SO PERFECT!
« Reply #4 on: December 23, 2008, 12:55:03 AM »
Milling machine?

Lucky b4stard, is it a bridgeport or a micro mill (sieg X1) ?

Ahh, I really want a sieg x1.

Did you make the jig?

Can't wait to use my cnc router to do that.

Sigs by Alien_X
www.ax-elec.com

Offline ryan0

  • I EAT STUFF
  • Millennium Poster
  • *
  • Posts: 1128
  • Post quality +0/-0
  • Gender: Male
  • I LIEK CHEEEEZE
Re: UMD DOOR SO PERFECT!
« Reply #5 on: December 24, 2008, 09:57:42 AM »
Milling machine?

Lucky b4stard, is it a bridgeport or a micro mill (sieg X1) ?

Ahh, I really want a sieg x1.

Did you make the jig?

Can't wait to use my cnc router to do that.

It's not a cnc,just a manual control,I made the jig with the cnc mill at my school.
the jig presses againt the smooth section of the drill bit so the jig itself can't get cut.It guides the bit around and doesn't let it astray.
Derp.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: UMD DOOR SO PERFECT!
« Reply #6 on: December 31, 2008, 02:44:13 AM »
Cool, you could also use a rotary table.

Sigs by Alien_X
www.ax-elec.com

Offline PhenomenalDesigns

  • Granny Spanker
  • *
  • Posts: 476
  • Post quality +0/-0
  • Gender: Male
Re: UMD DOOR SO PERFECT!
« Reply #7 on: December 31, 2008, 11:17:02 AM »
I just use a dremel

Just be careful with it, and set it to a slow speed, and make sure you have good hand eye co-ordination


Hoi! Pinoy ako!

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: UMD DOOR SO PERFECT!
« Reply #8 on: December 31, 2008, 10:42:08 PM »
I find the best way is to use a cutting wheel on medium speed, then a sander bit on high speed until there is a small lip, then lower the speed and finish it perfect and if needed use some fine sand paper. (Dremel is used for all)

But its really what you prefer and what tools you have..

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal