Author Topic: Modded controller not charging  (Read 1927 times)

Offline Bullet Pulse

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 55
  • Post quality +0/-0
Modded controller not charging
« on: February 02, 2009, 12:51:20 PM »
Whenever I plug in my play and charge cord to my self-modded controller (COD World At War RapidFire Kit On triggers CG Install),
the charger light will stay lit for about a minute and then turn green.
When I take off the charger, the battery only lasts for about 2 seconds and then fades out.
I can charge the battery pack completely fine using my other controller and then put it back in the modded controller, so that proves that the battery pack is not defective.
Can anyone figure this out?

Offline moeiscool

  • Ω Allumnist Ω
  • *
  • Posts: 139
  • Post quality +0/-0
  • Gender: Male
Re: Modded controller not charging
« Reply #1 on: February 02, 2009, 06:47:31 PM »
maybe you damaged a pin that allows the controller to charge the battery?
maybe you somehow smacked a pin by the sync button when soldering to it? (if you did solder to it)
really look at your circuit board see what COULD be stopping from charging to happen
theres ribbons that run along the board maybe you ripped one out, its tough but its a possibility.

i hope you fix your controller bullet sucks to get it modded then it screw up :(
PLEASE DONT USE REFERRAL BANNERS IN YOUR SIG
Signed
Mac

Offline Bullet Pulse

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 55
  • Post quality +0/-0
Re: Modded controller not charging
« Reply #2 on: February 03, 2009, 10:40:22 AM »
I know it's something wrong with the board,
but does anyone have any knowledge about the controllers
and how they charge and etc.

Offline moeiscool

  • Ω Allumnist Ω
  • *
  • Posts: 139
  • Post quality +0/-0
  • Gender: Male
Re: Modded controller not charging
« Reply #3 on: February 03, 2009, 05:42:22 PM »
check the ribbons in the controllers charge port where the wire goes into maybe they got bent and pushed back and cant make a circuit
PLEASE DONT USE REFERRAL BANNERS IN YOUR SIG
Signed
Mac

Offline PspKicks316

  • Acidmods Alumni
  • Mad Bomber
  • *
  • Posts: 5709
  • Post quality +5/-4
  • Gender: Male
Re: Modded controller not charging
« Reply #4 on: February 03, 2009, 06:18:52 PM »
check the ribbons
There's no ribbons on wireless controllers...
I have 4, and no ribbons.


....

Offline moeiscool

  • Ω Allumnist Ω
  • *
  • Posts: 139
  • Post quality +0/-0
  • Gender: Male
Re: Modded controller not charging
« Reply #5 on: February 07, 2009, 12:20:56 AM »
ok when i say ribbons i mean the thingies
that go along the board
ya know the circuit thingies
those little path way doo hickys
i unno
make sure none of those are
dead in anyway
and the contacts inside the head of the charge input
PLEASE DONT USE REFERRAL BANNERS IN YOUR SIG
Signed
Mac

Offline Nemesis

  • Millennium Poster
  • *
  • Posts: 1186
  • Post quality +0/-0
  • Gender: Male
Re: Modded controller not charging
« Reply #6 on: February 07, 2009, 05:21:30 AM »
ok when i say ribbons i mean the thingies
that go along the board
ya know the circuit thingies
those little path way doo hickys
i unno
make sure none of those are
dead in anyway
and the contacts inside the head of the charge input

The circuit traces.

Offline moeiscool

  • Ω Allumnist Ω
  • *
  • Posts: 139
  • Post quality +0/-0
  • Gender: Male
Re: Modded controller not charging
« Reply #7 on: February 07, 2009, 05:32:04 PM »
yes, those thank you.
i know my way around a little but have no idea of the names of things
i used to call capacitors black electro cylinders.... haha
PLEASE DONT USE REFERRAL BANNERS IN YOUR SIG
Signed
Mac

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal