« previous next »
Pages: [1]   Go Down

Author Topic: Sync Button Broke Off The PCB - Help  (Read 2488 times)

Offline Joe4x2

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
Sync Button Broke Off The PCB - Help
« on: June 13, 2009, 05:42:13 PM »
Hi all - I have a controller that has a sync button that broke off and ripped the solder pads along with it right off the PCB. Can anyone help me find a good solution for new solder points? I thought I saw some super high res. pictures of the traces somewhere on here but I am having no luck searching today.

I have run jumpers for some LEDs before when I ruined their pads so hopefully I can find out some points to jump from and use a tact button or something similar.

Logged

Offline F4thAcE

  • Hillbilly Modder
  • Motor Mouth
  • *
  • Posts: 88
  • Post quality +0/-0
  • Gender: Male
  • i live in the country my neigbors are trees.
Re: Sync Button Broke Off The PCB - Help
« Reply #1 on: June 13, 2009, 07:47:36 PM »
hmm... can you show some pics im having a hard time understanding what your saying.
Logged

Offline Joe4x2

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
Re: Sync Button Broke Off The PCB - Help
« Reply #2 on: June 13, 2009, 10:44:32 PM »
Sure, Here you go. As you can see in the upper left hand corner where the sync button normally is, it is gone.....and so are all the solder pads.


Logged

Offline Ben.

  • Club AM VIP
  • Acid Modder
  • *
  • Posts: 657
  • Post quality +2/-0
  • Gender: Male
Re: Sync Button Broke Off The PCB - Help
« Reply #3 on: June 14, 2009, 12:36:31 AM »
Ouch.. It may be repairable...

Not sure how..:/
Logged

Offline F4thAcE

  • Hillbilly Modder
  • Motor Mouth
  • *
  • Posts: 88
  • Post quality +0/-0
  • Gender: Male
  • i live in the country my neigbors are trees.
Re: Sync Button Broke Off The PCB - Help
« Reply #4 on: June 14, 2009, 06:30:14 AM »
okay ill look into it a bit more i got to go to church ill get back to you afterwards
Logged

Offline moeiscool

  • Ω Allumnist Ω
  • *
  • Posts: 139
  • Post quality +0/-0
  • Gender: Male
Re: Sync Button Broke Off The PCB - Help
« Reply #5 on: June 14, 2009, 09:17:02 AM »
you could wire a button to it and have it taped to the outside or smthn
Logged
PLEASE DONT USE REFERRAL BANNERS IN YOUR SIG
Signed
Mac

Offline Joe4x2

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
Re: Sync Button Broke Off The PCB - Help
« Reply #6 on: June 14, 2009, 10:00:03 AM »
I would love to wire a new button on the board however I don't know where to place the wires since the solder pads are gone.
Logged

Offline F4thAcE

  • Hillbilly Modder
  • Motor Mouth
  • *
  • Posts: 88
  • Post quality +0/-0
  • Gender: Male
  • i live in the country my neigbors are trees.
Re: Sync Button Broke Off The PCB - Help
« Reply #7 on: June 14, 2009, 10:55:51 AM »
okay well... i don't have a matrix board so i can't look at mine to help you but you can try to trace it and solder the source and then put in a tact switch and your in buisness
Logged

Offline injungleist

  • Club AM VIP
  • Who Farted ???
  • *
  • Posts: 200
  • Post quality +0/-0
  • Gender: Male
  • mod your face off.
Re: Sync Button Broke Off The PCB - Help
« Reply #8 on: June 14, 2009, 01:25:51 PM »
Logged
thx gamerdude767
trades w/ blazinkaos
purchases from sniper (fast shipping)
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal