Dumping & Flashing the Lite on DG-16D2S-09C FW Ver:83850C Tutorial Video Added

[KingMike_OS]

Dumping & Flashing the Lite on DG-16D2S-09C FW Ver:83850C & Liteon 93450C 


WARNING!!
Do at your own risk
This mod is very advanced! Acidmods.com is NOT responsible for any damage done to your DVD drive or Xbox 360.
Do at your own risk!!


Introduction
This tutorial will teach you to flash and dump a DG-16D2S-09C Lite on Xbox 360 DVD Drive.
Flashing will enable the ability to use backup's of your games and other cool things.
Try this at your own risk!


Parts Needed-
-- DVD Drive
-- Mini On/Off Switch (http://www.radioshack.com/product/index.jsp?productId=2062498)
-- 22 ohm 1/2W 5% Carbon Film Resistor (http://www.radioshack.com/product/index.jsp?productId=2062311)
*-- VIA VT6421A chipset card (https://acidmods.com/shop/product_info.php?cPath=12&products_id=99)


*- You don't NEED this but this will make it alot more simple to do!

Tools Needed-
-- Carbon Pen (Recommended for removing solder mask!) (Link)
-- Exacto Knife/ Razor blade
*-- 360Xtractor Pro v1.2 (https://acidmods.com/shop/product_info.php?cPath=12&products_id=102)
-- Soldering Iron & Solder

*- You don't NEED this but this will make it alot more simple to do!

Software Needed-
-- JungleFlasher 1.67B  Download Link- http://jungleflasher.net/files/JungleFlasher.0.1.67.Beta.rar

Average Time To Complete- About 2-3 hours

Difficulty Rating-5/5

Step By Step Tutorial-
Ok first we need to open the 360. This tutorial can be found here- https://www.acidmods.com/forum/index.php/topic,32902.0.html which is supplied by our good friend, Modded Matt.

Next we grab out our DVD drive by unplugging the Sata and Molex power plugs.

Notice the Model and Firmware of the drive.


 
Then flip over the drive and find the 4 screws holding the Drive together and remove them.


Next unplug all of the zif connectors by sliding them out of place and pulling out the plugs.
**Note : There are 2 screws holding the Board in place removed them **

Now flip the board over and find this spot- (Notice the caps and sticker)


A closer picture of the spot we are going to be doing work on.


Here is a basic diagram of what we have to do-


First we clean up the spots using our carbon pen or if you dont have one, use a razor (BE VERY CAREFUL!)


Next cut the spots shown in the diagram like so-


Now solder the wires on the board like so-




Make sure there is about 1 foot of wire coming off of the purple and black wire!

Now just close up the DVD Drive makeing sure to plug in all of the Zif's and make sure everything looks like it was in the begining.
ALSO, make sure to cover up the solder spots with some electrical tape or something to prevent shorts in the drive. (That is bad.)

Have the Purple and black wire come out of the drive like so-


Now Wire up The GND [Black Wire] to A 22~Ohm Resister than to one of the pin on the Switch and Pin 101 [Purple Wire] to another pin on the Switch like so-


Connect the drive up to the VIA VT6421A chipset card and 360Xtractor Pro v1.2-




Video Part One: The Dumping Of the Original FW and Key "Lite on DG-16D2S-09C FW Ver:83850C "

Dumping the Lite on DG-16D2S-09C FW Ver:83850C Tutorial


Now that we have our key remove the switch and fix all the cut trace's and put the drive back together.

[SN!P3R]

Mike, I love you.

No homo

[G.R.E.A.M]

Nice tutorial. I definitely will be using this.
Just wondering where did you get the pen. I forgot the name. It's used to reveal the copper. Another questions what did you use to cut the traces.

I just tried this today and got completely lost. sorry for my noobness.   

[Jumbo]

Nice tutorial. I definitely will be using this.
Just wondering where did you get the pen. I forgot the name. It's used to reveal the copper. Another questions what did you use to cut the traces.

I just tried this today and got completely lost. sorry for my noobness.   

carbon pen look on ebay and u use a exacto knife or any other razor blade

[KingMike_OS]

German fine 1.7 mm fiberglass scratch brush pen tool:

http://cgi.ebay.com/German-fine-1-7-mm-fiberglass-scratch-brush-pen-tool_W0QQitemZ310164111034QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item483738beba

Lot of 2 thin 1.7 mm fiberglass scratch brush refills : 

http://cgi.ebay.com/Lot-of-2-thin-1-7-mm-fiberglass-scratch-brush-refills_W0QQitemZ400039004170QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item5d242ec80a

[G.R.E.A.M]

Thanks!
I am going to order one asap.

Also is the 83850c flashed the same as the 93450c?
My final question(I promise no more after this) whats the difference between 83850c and 83850c-v2?

[KingMike_OS]

Also is the 83850c flashed the same as the 93450c?
My final question(I promise no more after this) whats the difference between 83850c and 83850c-v2?

yes this will work on all lite on drive and FW ... even the 93450C
don't need it for firmware version 74850c "use spear or the probe to get the key", on some of the 83850C  50/50 "No probe needed".  now some of the 83850C depends on manufacture date can be dump using a diff way " using LO83 & Info Key In Windows or MS DOS  which i show later but its %50/50 chance that it works. if it works great good for you ... and no opening drive needed. if don't that have to do it this way.
V2 have to be dump this way no other way.
 

[G.R.E.A.M]

Thanks for sharing your knowledge mike. It is greatly appreciated. I kinda knew some of that but you just made the little guys in my head trying to figure this out alot happier.

I am going to be doing two 93450c's tomorrow. Wish me luck 

EDIT:

Look what I did lol. I had an extra 74850c lite-on so I took it apart and practiced. Also made a cool little switch w/resistor board.







Just waiting to get my power supply thing from Acidmods shop. The Xtractor I think. I ordered a couple days ago, I am hoping it'll be here soon.

Thanks again for the fantastic tutorial. 

[SN!P3R]

Yes thank you mike. This is excelent. Did you find how to read from the drive? Anyways, thanks. And are you waiting for iExtreme LT it are you flashing to 1.61?

[johnblazer]

i've manage to dump the liteon 83850c v2 09c drive thanks for the tut now how do i flash it

[SN!P3R]

We need to wait till the iextreme team comes out with a firmware for it. I'd say by the nd of January

[SN!P3R]

Double post: I was reading on X-Box scene a couple minutes ago, and it seems that iExtreme 1.61 has come out for the 93450 drive. It's NOT xbl safe, but if you don't play on live it's no problem.

[syko]

Great tutorial but is there a 2nd Video??

[joaor111]

do you really need this VIA VT6421A cause i did everything and i have the xtractor the only thing i dont have is the  VIA VT6421A i cant get the intro / Device id  it says resend vendor intro until i get an error ( and flash chip properties is blank) thank you for the help by the way my F/W is 9345oc

[techninjadude]

Is this for the Xbox Slim 4gb Version and do you have to remove the switch and solder traces

[frenulem - No.5417]

Dumping & Flashing the Lite on DG-16D2S-09C FW Ver:83850C Tutorial Video Added
« on: 13 December 2009, 09:08:41 »
« on: 13 December 2009, 09:08:41 »
13 December 2009, 09:08:41

Use some common sense lad

[techninjadude]

Kool Thx I knw dat but i wanted confirmation, I am not on xbox hacks to much.
And i just found out that if you hack it youll get banned once you conect to xbox live