Viking360 Controller w/Custom XCM Case!

[Thejld]

Ben points N,L, and K, those r right next to the chip on the back, do u solder to those or is there another point u can use instead of that?

[Ben.]

I didn't like soldering them to the points next to the chip, I got too many problems so I found some alternative points on the top of the board

[smithy141]

i looked at what you have on your site, but just wondering when your ebay listings are goin back up?




And also happy birthday!!

[Ben.]

Why thank you

They will be up in the next couple of weeks or so

[smithy141]

thats ok, and will have what you usually have listed?

And what about the mw2 prestige service?

[Ben.]

Yarpp

[smithy141]

??
Post Merge: June 24, 2010, 12:48:57 PMjust noticed aswell, that we both live in north devon lol

[Thejld]

Ben do u hav a picture of the points u use instead of those?

[Ben.]

Where do you live TS? I'm in Littleham, a little village near Bideford.

and I have a picture somewhere, check out the Viking360 forums, there are pics up there and shizzle

[Thejld]

k is it one of ur forums, cause i was lookin over there and coudlnt find it.

[Ben.]

I'm not sure, what exact points do you want to know? and I will draw them on a scan of a CG2 board

[smithy141]

me i live in ilfracombe which is near bideford lol

[Ben.]

You've ordered from me before haven't you, I have posted some orders to Ilfracombe

[smithy141]

yes you did me a rapid fire controller service n iv done your mw2 service three times lol

[Ben.]

Yeah I remember that

Maybe you could do a review of my shop on the forum, I think there is a area for that?

[smithy141]

ok what on here?

[Thejld]

Ben points N,L,E,and K, and the D+ and  the D- ones, dont hav to draw those out but are those mandatory points or only if u do pnc?

[Ben.]

D+ and D- are needed for you to program the chip, which you need to do once it is installed as it has no preset loaded onto it before installation. You need them to go either to a 3.5mm Jack or to the Pnc port.

Is this for a Duo or Raven?

[smithy141]

where am i able to do that?

[Thejld]

U mean sleeper or raven lol and this is for raven

[Ben.]

Here I think: https://www.acidmods.com/forum/index.php/board,405.0.html

U mean sleeper or raven lol and this is for raven

That is what I mean haa. Ok I'll do it now

[smithy141]

your shops not there?

[Ben.]

Add a new topic

And heres the diagram, its bad I know but you should be able to spot the points.

The K & L are the bottom of each LED.

Pic attached.

Credit to RDC for the pic.

[smithy141]

is it alryt to use your site in the review?

[Ben.]

Of coursee

[Thejld]

Ben howcome the guide has l and k right next to the chip and not on the leds, thats wierd cuz i would hav thought it would have shown it to be on the leds in the beginning, and if i wired something rong the first time is there a possibility the chip is fried, like hav u wired something worong b4?

[Ben.]

Well Einar (Guy who runs Viking360) decided to do the pinout like that, the points I have shown you there are 100% fine to use

[Thejld]

Yea ik, do they hav to be on the bottom of the led, and if i wired something wrong, would the chip fry?

[Ben.]

It wouldn't fry, the bottom of the LED is the positive side, and that's the side it needs to be on to supply power through the LED, it will just not work on if you wired it to the top.

[Thejld]

Thanks ben, how would the chip fry is there anyway