Battlefield 4 schematics are as followed: connection (1) goes to RB & connection (2) goes to LS.
COD Ghost schematics are: connection (1) goes to "B" & (2) goes to "A".
Veiw the schematics below for instillations. Pic #4 shows the proper connection to solder the led to. View all other pics for button and trigger locations.
Veiw pic#3 for alternative positive power sourse. If u look across to the left from the LS connection u will see a test point #9 or (TP9) on the board. This is much easier to use when mounting your chip or chips to the backside of the board.
Pic#5 shows a good spot to wire your ground pin to.
If u decide to do a dual chip setup wire pins 1,2,3,5 & 8 together on both 12f1822 microchips. From there just run 1 wire from any of the two chips to the solder locations on the controller PCB board following the schematics on pic#1 & 3. All that's left is running the wires from pins 6 & 7 (labeled button connections as (1) & (2) in the schematic print pic#1) to the button locations specified for the individual hex code the chip was programmed for. Then u will have to hook up two 6×6×7 mm tactical buttons (spst) from both microchips.
I'll update more when I get a chance. I'll post codes to members only through PM and a drop box link. I'll post my mod roster here shortly. They will both now be 10 modes each.
Here is my mod roster!
COD Ghost codes:
XB1 DS Always Drop     
XB1 Drop Shot + LT Cancel     
XB1 DS Always Drop Reset     
XB1 LT Cancel Drop Shot Reset     
XB1 Jump Drop shot     
XB1 Jump Drop shot LT Cancle     
XB1 Jump Drop shot reset     
XB1 Jump Drop Shot + LT Cancel Reset     
XB1 Auto Akimbo + RT Aim Assist     
XB1 Auto Akimbo + RT Aim Assist DS     
XB1 Auto Akimbo + RT Aim Assist DS Reset     
XB1 Auto akimbo + RT Aim Assist Jump DS     
XB1 Auto Akimbo + RT Aim Assist Jump DS Reset    
XB1 4 SPS UA     
XB1 8 SPS UA     

Battlefield 4 codes
XB1 12 SPS UA     
XB1 BF4/COD RF 20 SPS UA     
XB1 BF4 RF 16 SPS UA     
BF4: LT auto spot + sprint     
BF4: autospot & auto sprint     
XB1 Akimbo 8 SPS UA     
XB1 Akimbo 20 SPS UA     
XB1 Auto Breath/LT sprint     
XB1 Auto Run     
BF4 LT Quickscope-UA     
BF4 RT Quick Scope - UA     
XB1 8 Round Burst UA     
XB1 7 Round Burst UA     
XB1 6 Round Burst UA     
XB1 4 round burst     
XB1 Double Tap RT UA     
Ghost RT QS     
Ghost LT QS     
Universal RT Quickscope     
Universal LT Quickscope     
COD Ghost Auto Aim     
XB1 Semi Autos 13.89 SPS 25% Duty cycle UA   
The akimbos and burst shot codes I've made can be used on both chip as far as programming goes. The quickscopes unfortunately have to be coded to the BF4 chips. This is why its best to do a dual chip setup. So much more benefits + being able to run 2 modes at once. A lot of my codes already run multiple mods at once. This will give u all a idea of what I have to offer.
Let's just say u tell me what modes u want in what order or a specific rapid fire speed u want and I'll custom make u a hex around your settings up to 10 modes for each individual chip.  
  
Here are pics for the dual chip setup. In this pic u will take your two flashed chips then cut the legs short on your microchip. Remember to label what chip is what, be that a sticker or something other.
Here is a pic of the chips being solderd together by pins 1 & 8. Make sure the chip is flipped on the other chip correctly where the same pins line up.
Here is a pic of pins # 2 & 3 being linked together.
Here is a pic of pins#5 being linked together.
Now all u have to do is run one wire from the linked chips to the board connections power, ground, led, LT & RT. Then connect pins 6 & 7 to the locations based off my schematics for the individual chip, ex( BF4 chip (1) goes to RB (2) goes to LS; Ghost chip (1) goes to B (2) goes to A) this is based off the schematic in pic#1 at the top of the thread.
U will also need to wire 2 tac switches to run each individual chip. I'll update where to mount the chip or chips and a operations guide at a later time.
