« previous next »
Pages: [1]   Go Down

Author Topic: Possible PS2 LED/elwire power points???  (Read 3499 times)

Offline redryno1221

  • Granny Spanker
  • *
  • Posts: 430
  • Post quality +0/-0
  • Gender: Male
    • Redrynotuts
Possible PS2 LED/elwire power points???
« on: December 09, 2007, 07:44:48 PM »
can someone confirm that this works and is not total B.S..... supposedly it is a 5.1v point but I don't have a multimeter can someone confirm this



Download full tut here

T3h_0v3rl0rd: Made Pics smaller for you :)
« Last Edit: December 24, 2007, 11:57:25 AM by T3h_0v3rl0rd »
Logged

Offline Tec_

  • EL-Wire King
  • E = MC² Mad Scientist
  • *
  • Posts: 1869
  • Post quality +2/-0
  • Gender: Male
  • EL Wire King
Re: Possible PS2 LED/elwire power points???
« Reply #1 on: December 10, 2007, 06:45:20 AM »
resize pics much? and why dont you use the power off the fan? just tie in to it in parallel you get i think its around like 4.5v
Logged

Offline ryan0

  • I EAT STUFF
  • Millennium Poster
  • *
  • Posts: 1128
  • Post quality +0/-0
  • Gender: Male
  • I LIEK CHEEEEZE
Re: Possible PS2 LED/elwire power points???
« Reply #2 on: December 10, 2007, 06:54:47 AM »
dude thats an 11 volt point as far as i know...its definitely not 5 cos i'm powering a large fan with lights off it
Logged
Derp.

Offline redryno1221

  • Granny Spanker
  • *
  • Posts: 430
  • Post quality +0/-0
  • Gender: Male
    • Redrynotuts
Re: Possible PS2 LED/elwire power points???
« Reply #3 on: December 10, 2007, 05:28:43 PM »
So then I should just connect it to the fans solder points  :dntknw:
Logged

Offline jrfhoutx

  • The Long-Winded One
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 2582
  • Post quality +35/-8
  • Gender: Male
  • Dōmo, Konnichiwa, :censored:es...
    • Misadventures in Mediocrity and Modding
Re: Possible PS2 LED/elwire power points???
« Reply #4 on: December 10, 2007, 06:50:16 PM »
actually that's a 12v point, you can use that, just put the proper ohm resistor inline and you shouldn't have any problems. you could tie into the fan but then you have to worry about changing the resistance, current and voltage values of the fan circuit and can run into problems there.

here's a good pic of the 12v point that was given to me when I started modding my PS2...

https://www.acidmods.com/forum/index.php?topic=3289.msg34670#msg34670

oh and seriously, hit up radio shack and spend the $20 on a digital multi meter, they're worth every penny...
Logged
AcidMods Ninja... You won't know I'm there until you're gone...


All of these sigs are from the original acidmods sig comp...  @jrfhoutx  "No respect, no respect at all... that's the story of my life." --

Offline ryan0

  • I EAT STUFF
  • Millennium Poster
  • *
  • Posts: 1128
  • Post quality +0/-0
  • Gender: Male
  • I LIEK CHEEEEZE
Re: Possible PS2 LED/elwire power points???
« Reply #5 on: December 11, 2007, 08:54:53 AM »
yup its fine to use sorry i meant 12v not 11v  :drunk: dont solder to the fan connector use the points in the pic just get a proper resistor
Logged
Derp.

Offline Tec_

  • EL-Wire King
  • E = MC² Mad Scientist
  • *
  • Posts: 1869
  • Post quality +2/-0
  • Gender: Male
  • EL Wire King
Re: Possible PS2 LED/elwire power points???
« Reply #6 on: December 11, 2007, 09:00:40 AM »
JR is right about the fan, but i haven't run in to any problems and when it comes to amperage in fans unless you need the torque its not a big deal
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal