Author Topic: PSP Trigger Mod fixed pictures (Read 76583 times)

Jumbo · « **Reply #30 on:** August 04, 2008, 08:19:29 AM »

Motherboard style for this mod doesnt matter....

3mm is pretty big i wouldnt use it use 603 or 804 smd leds from ebay or mouser

Jsunscustomz · « **Reply #31 on:** August 07, 2008, 03:14:53 AM »

Bravo for a job well done! I really appreciate this. I'll be using it shortly and I just want you to know that I thank you guys for sharing the info and your hard work.

PSPpanda · « **Reply #32 on:** August 20, 2008, 08:04:11 AM »

Help

I bought 50 blue 0603 SMD LEDs off ebay. I dont know how to calculate the resistor i need for this tutorial. Can someone please help!

Voltage for one:3.0v Amps:20 mA
Thanks

tripsalot · « **Reply #33 on:** August 20, 2008, 08:28:15 AM »

http://ledcalc.com/

here you go,just use this

sethion · « **Reply #34 on:** August 23, 2008, 06:45:42 PM »

Ok im a bit of a noob when it comes to circuit diagrams and translating them into what is needed. Anyone know any good sites to get me started on ?

buickgnx · « **Reply #35 on:** August 31, 2008, 07:04:30 AM »

do i sodder the wire for one led to the other or some were down the line?

OmegaNemesis28 · « **Reply #36 on:** September 06, 2008, 10:11:29 AM »

please help. It appears I have a different motherboard. Does anyone know where I can find a tut with my mobo?

Jumbo · « **Reply #37 on:** September 06, 2008, 03:45:12 PM »

Quote from: OmegaNemesis28 on September 06, 2008, 10:11:29 AM

please help. It appears I have a different motherboard. Does anyone know where I can find a tut with my mobo?

Are you kidding or just dumb?

That is called a slim. This tut is for phat.

SN!P3R · « **Reply #38 on:** September 11, 2008, 02:47:01 PM »

the 3mm are too thick. i tried it, you wont be able to use the trigger buttons there after. also, i think the tut was made on a TA-79 pcb. correct me if im wrong.

Jumbo · « **Reply #39 on:** September 11, 2008, 05:00:21 PM »

If you have a PHAT psp it doesn't matter what style motherboard you have as long as its a PHAT PSP.

ndru98 · « **Reply #40 on:** September 29, 2008, 08:28:19 PM »

I dont get the part where you route the wires after soldering. So u poke the wires through the hole, and then solder the 2 other ends of the wires that arent tied, to to negative and positive points, right? Then where do you solder the leds on to?

whitetop · « **Reply #41 on:** October 03, 2008, 05:05:55 AM »

Quote from: ndru98 on September 29, 2008, 08:28:19 PM

I dont get the part where you route the wires after soldering. So u poke the wires through the hole, and then solder the 2 other ends of the wires that arent tied, to to negative and positive points, right? Then where do you solder the leds on to?

thats were you get the power solder the other end to your leds and theres your trigger mod

ndru98 · « **Reply #42 on:** October 03, 2008, 03:13:10 PM »

Dude.. I know that... but then, Im asking, in the picture, it says to make a knot at one end of the 2 wires, tie a know, and slip it through the whole. and the other end goes to ground and positive. Or... do you make the knot in the middle? Or.. like.... from the 2 ends, you wire 2 wires from negative, and 2 wires from positive... then like.. solder those to LED?

whitetop · « **Reply #43 on:** October 03, 2008, 04:03:17 PM »

as you see in the picture the not is stopping the wire from beining pulled from the soldered points so if you make the not pull threw the hole then the not should be onthe front of the board so if you pull on the other side the not stops the pulling so while you solder the points then the leds you can keep it all connected

ndru98 · « **Reply #44 on:** October 03, 2008, 04:25:33 PM »

Ok... so the knot.... keeps it from falling out.. and you tie the know at the end right? Then use the other 2 ends to solder to ground and positive, right? Then where do you solder the LEDS to? O.O

whitetop · « **Reply #45 on:** October 03, 2008, 05:16:52 PM »

not the part by the power points the leds go to the other end of the wire

ndru98 · « **Reply #46 on:** October 03, 2008, 06:00:57 PM »

Errm... what?

whitetop · « **Reply #47 on:** October 03, 2008, 06:11:05 PM »

ok were the power points are on the power board make a not the thread it in the hole and solder the short end to the power board and the long end for the leds

ndru98 · « **Reply #48 on:** October 03, 2008, 07:28:51 PM »

O!!! Thats what I was asking, do I make the knot at the end, or in the middle. But now I get it.. you make it like so one end is smaller, the small end goes to the + and -. And the other end goes to the LEDS... lmao, I get it.. then the resistance goes where? O.O

whitetop · « **Reply #49 on:** October 04, 2008, 06:28:30 AM »

all credits go to 4dP and TheG4mer on this tut i just fixed all this so people have a working tut instead of keep asking how to do it

read people and Alien_X thats who made it with all permission of them not just chaos and dont edit my post plz unless its a very good resion

buickgnx · « **Reply #50 on:** October 04, 2008, 06:12:24 PM »

what would be cool is power/ charge triger mid. have preaty much 2 tirger mods in 1 soderded to the power fuse and the other to the charge so when u charge you get a diffrent color

whitetop · « **Reply #51 on:** October 04, 2008, 06:22:50 PM »

mite be a good idea post your idea here https://www.acidmods.com/forum/index.php?board=308.0 or in psp section

gayazz · « **Reply #52 on:** October 18, 2008, 10:44:33 PM »

hey i know this is a nooby question but whats a flux.

whitetop · « **Reply #53 on:** October 20, 2008, 08:56:18 AM »

Quote from: gayazz on October 18, 2008, 10:44:33 PM

hey i know this is a nooby question but whats a flux.

its like gel but for soldering wires and other stuff better

eculewatt · « **Reply #54 on:** October 20, 2008, 04:45:47 PM »

ok guys, im a bit new to this so i have a couple questions

i want to buy these LED's here: http://www.unique-leds.com/index.php?target=products&product_id=1736

so should i buy this resistor here?:http://www.radioshack.com/sm-10-ohm-10w-5-wirewound-resistor2-pack--pi-2062291.html

where should i get 30 gauge wire from(specific link?)

where exactly do i solder the resistor to?

thanks in advanced!!

whitetop · « **Reply #55 on:** October 21, 2008, 04:40:30 AM »

mount work better for led swaping just get normal 0603 leds

for the wire go to ebay or coolmods if they still sell it.

the resistor is shown in step one

eculewatt · « **Reply #56 on:** October 21, 2008, 04:38:45 PM »

ok, so i took a look at the image in step 1 and i just need you to clarify it to me

how do both of the leds positive wire solder to one side of the resistor? because the other end of the resistor has to be soldered to the positive point on the board, only leaving one point for a led to be soldered to.

and also, kinda the same question for the negative wires. how do both leds negative wires end up only soldering to one spot on the board

thanks again
hopefully ill understand this after this question

JoaoPais · « **Reply #57 on:** December 11, 2008, 08:03:45 AM »

If I do this tut and I want to have sound reactive leds, what I've to do? It's better to do the other tut?
And other thing..... if I want to turn ON/OFF the LED's, want I have to do? A dip switch?

Thanks, and help this noob

bustinthejustin · « **Reply #58 on:** December 11, 2008, 12:47:56 PM »

Quote from: buickgnx on October 04, 2008, 06:12:24 PM

what would be cool is power/ charge triger mid. have preaty much 2 tirger mods in 1 soderded to the power fuse and the other to the charge so when u charge you get a diffrent color

Good idea. I might try this when I get bored.

JoaoPais · « **Reply #59 on:** December 12, 2008, 01:27:25 PM »

If I do this tut and I want to have sound reactive leds, what I've to do? It's better to do the other tut?
And other thing..... if I want to turn ON/OFF the LED's, want I have to do? A dip switch?

Thanks, and help this noob

Please, answer this reply......!!!!!......

News:

Author Topic: PSP Trigger Mod fixed pictures (Read 76583 times)