Author Topic: Fitting the razorX  (Read 2731 times)

Offline longcat1

  • Chief squatting Hard
  • *
  • Posts: 15
  • Post quality +0/-0
Fitting the razorX
« on: July 29, 2008, 02:01:56 PM »
so how do u fit the board in there? the screw thing is in the way and the board is overlaping some of the x button. :confused:

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: Fitting the razorX
« Reply #1 on: July 29, 2008, 02:05:37 PM »
you gotta dremel that out....

Offline ryan0

  • I EAT STUFF
  • Millennium Poster
  • *
  • Posts: 1128
  • Post quality +0/-0
  • Gender: Male
  • I LIEK CHEEEEZE
Re: Fitting the razorX
« Reply #2 on: July 29, 2008, 03:10:27 PM »
you gotta dremel that out....
what he said......lol,i recommend chopping what you dont need from the powerboard,theres actually alot u can take off without interfering with the buttons,it makes it much easier than not cutting the pwoerboard,also cut the screwhole on the faceplate,dremel a square for the analog nub to fit snugly into the faceplate,chop out the clip that holds down the bottom of the powerboard to the backplate,basically chop what you can
Derp.

Offline longcat1

  • Chief squatting Hard
  • *
  • Posts: 15
  • Post quality +0/-0
Re: Fitting the razorX
« Reply #3 on: July 29, 2008, 06:53:14 PM »
awww i dont have a dremel, o well i guess i can  cut and sand for a year, thx for the help :D

Offline Tri-edge

  • I found Nemo!!
  • Around the block
  • *
  • Posts: 2381
  • Post quality +4/-0
  • Gender: Male
  • Azure knight
Re: Fitting the razorX
« Reply #4 on: July 29, 2008, 07:31:11 PM »
if your really careful you can melt it with your soldering iron

Offline longcat1

  • Chief squatting Hard
  • *
  • Posts: 15
  • Post quality +0/-0
Re: Fitting the razorX
« Reply #5 on: July 31, 2008, 02:08:53 PM »
well i managed to cut it with an xacto so yay but does anyone kno how to make a good hole cuz i tryed drilling but i lost a faceplate :cry2:

Offline Ch4rL13

  • R4z3R
  • Acid Modder
  • *
  • Posts: 869
  • Post quality +0/-0
  • Gender: Male
    • R4z3R Gaming
Re: Fitting the razorX
« Reply #6 on: July 31, 2008, 02:19:35 PM »
well i managed to cut it with an xacto so yay but does anyone kno how to make a good hole cuz i tryed drilling but i lost a faceplate :cry2:

ehh well this is where the dremel would come in, i would guess you draw a circal the best u can and dremel that out, or maybe you could melt a whole wit ur iron and sand the melted part out? lol


Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: Fitting the razorX
« Reply #7 on: July 31, 2008, 03:24:07 PM »
You eitehr need a dremmel or a mill to cut that out. I would suggest sending it to somebody. I got a faceplate from ryan0 cut on his milling machine it was perfect :P

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal