Author Topic: UMD Door mod questions  (Read 1695 times)

Offline KrInEn

  • Motor Mouth
  • *
  • Posts: 83
  • Post quality +0/-0
UMD Door mod questions
« on: September 28, 2008, 12:31:36 PM »
I have read the tuts on installing the jewels and speakers into the umd door. All of them say to use a dremel. Now I am pretty good with a dremel but there has to be an easier less time consuming way. Also a way to get a much nicer circle

I just went to my local harbor frieght and picked up a 13pc hole saw kit for $3.49! and one in there fits just shy of the metal ring by a hair. enough room to clean it up with some sand paper. Anyone think this will not work? Please I need some input or if someone has done this before

Offline gr8npwrfl

  • Acid Modder
  • *
  • Posts: 582
  • Post quality +0/-0
  • Gender: Male
  • Ignorance is not fatal it can be cured
Re: UMD Door mod questions
« Reply #1 on: September 28, 2008, 01:01:53 PM »
Just make sure you cover the area with either masking tape or
duct tape . Start a very small hole at the center first for a guide.
Place the door on a wood block and tape down securely.

The plastic gets hot and sags as you use the hole saw. If you
do not support it, it will move the center point and you will not
get an accurate cut.

Cut at slow speed to minimize the heat build up which will cause
galling.


Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: UMD Door mod questions
« Reply #2 on: September 28, 2008, 02:46:17 PM »
Ya, I would be careful. And if you do it go full speed cause if you go slow it will give it time to heat up.
Then i could melt and get a bit messed up.
But i doubt it.
 :x:

Good Luck

Offline KrInEn

  • Motor Mouth
  • *
  • Posts: 83
  • Post quality +0/-0
Re: UMD Door mod questions
« Reply #3 on: September 28, 2008, 04:47:24 PM »
Wow so all you guys use a dremel to cut those out? man I hate doing circles with that thing, they always come out ummmm not round :P

Btw Jumbo, I find myself watching your damn sig for minutes on end. Almost expecting a different result or to see the aftermath :P
« Last Edit: September 28, 2008, 04:50:08 PM by KrInEn »

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: UMD Door mod questions
« Reply #4 on: September 28, 2008, 04:50:06 PM »
Ya i use one..

Offline squee

  • Chief squatting Hard
  • *
  • Posts: 16
  • Post quality +0/-0
Re: UMD Door mod questions
« Reply #5 on: September 28, 2008, 05:33:10 PM »
Ya i use one..

I couldn't find my dremel when I did mine, so I just used a soldering iron to melt most of it off, then used a box knife to get it perfect. Took a while, but the finish was well worth it.

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: UMD Door mod questions
« Reply #6 on: September 28, 2008, 05:43:58 PM »
I couldn't find my dremel when I did mine, so I just used a soldering iron to melt most of it off, then used a box knife to get it perfect. Took a while, but the finish was well worth it.

Thats bad for an iron.

Offline Cookie Monster

  • I SMELL SOMETHING
  • CyberPyrot WannaBe
  • *
  • Posts: 303
  • Post quality +6/-0
  • Gender: Male
  • GIMMIE COOKIE
Re: UMD Door mod questions
« Reply #7 on: September 30, 2008, 08:14:50 AM »
u could have just used a blade and some sand paper like i did(check psp tuts

thanks toad and indy for the sigglys

Offline squee

  • Chief squatting Hard
  • *
  • Posts: 16
  • Post quality +0/-0
Re: UMD Door mod questions
« Reply #8 on: September 30, 2008, 09:13:25 AM »
Thats bad for an iron.

Not really. The tip is the only thing. I just used a old tip.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal