Author Topic: New Product: PSP 1000 Dpad Breakout Board - No more soldering  (Read 10847 times)

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Hello acidmods

I am in the middle of finalizing my design for a PSP 1000 Dpad Breakout board. This will allow you to easily solder / piggyback the individual dpad button signals. It will be quick to install,low profile and easy to solder wires to.

Installation will only require you to file down part of the topside of the PCB and then insert into the Zif (ribbon) connector on the motherboard. The pcb wraps around the connector, fitting into unpopulated space of the motherboard. This design does not use fpcs and does not take up any space under the daughterboard. This simple circuitboard will allow you to build external controllers, analog controlled dpads and many many more peripherals without any soldering to the 0.5mm pitch zif connector. The item would be priced at around $10 to $15 and come preassembled. By following the installation manual you could be up and running in a matter of minutes!

Without further ado here are some previews:



Bottom:



Top:




I am hoping for this item to be sold through Sparkfun.com, and to aid with my market research, if you would be interested in such a product or have any thoughts or comments then please post in this thread.

Thanks.

Sigs by Alien_X
www.ax-elec.com

Offline atomicareprise

  • Registered BST
  • Acid Modder
  • *
  • Posts: 595
  • Post quality +2/-0
  • Gender: Male
  • FILIPINO SINCE BIRTH
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #1 on: April 08, 2009, 11:33:47 AM »
that's nice alien...soldering will be a breeze...
viperfan91 (phat), thaq93 (psp phat parts)
pinoyballa  (2 phats ), tri-edge (slim)
Awilliams357- to be shipped

Offline DubbleDutch

  • BlietZ Modding
  • Millennium Poster
  • *
  • Posts: 1234
  • Post quality +3/-0
  • Gender: Male


Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #2 on: April 08, 2009, 11:34:55 AM »
as i said on msn ;) this will make it a lot easier for people to do the external controller mod! :D



To all of you crying about lag and kicks, remember… when Jesus died, took him 3 days to respawn. Now THAT is lag.

Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #3 on: April 08, 2009, 11:44:06 AM »
Breakout boards FTW

Great job Alien.

Now we need something like that for the slim.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #4 on: April 08, 2009, 11:49:36 AM »
Thanks for the positive comments so far. However I can only bring this product to market if there is sufficient interest in the product, so along with your comments please could you post whether you would be seriously interested in purchasing one of these items for the aforementioned price.

Thanks again
Alien

Sigs by Alien_X
www.ax-elec.com

Offline treemty

  • l,,l METAL l,,l
  • Millennium Poster
  • *
  • Posts: 1231
  • Post quality +1/-0
  • Gender: Male
  • Will mod for food
    • the1337group.com
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #5 on: April 08, 2009, 12:12:32 PM »
I would seriously be interested in this :D
I wonder if you could make one for the ABXY area as well, as it would make installation for dual nubs easy for people who are not that goo  at soldering

Offline PhenomenalDesigns

  • Granny Spanker
  • *
  • Posts: 476
  • Post quality +0/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #6 on: April 08, 2009, 12:26:30 PM »
Nice, I think you should make one for the ABXY like treemty said, since many more people try to do the dual nub compared to external controler

Although I am quite interested in this


Hoi! Pinoy ako!

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #7 on: April 08, 2009, 12:39:44 PM »
Okay I will take that into consideration, thanks.
I think that the main reason people do not try the external controller is because they cannot solder the connector (Which isn't that hard if you have a microscope ;) )

If a person cannot solder the ABXY points for the dual nub, they surely wouldn't be able to solder the wires to the razor either, so there isn't too much point, especially for the psp 1000.

Sigs by Alien_X
www.ax-elec.com

Offline Tri-edge

  • I found Nemo!!
  • Around the block
  • *
  • Posts: 2381
  • Post quality +4/-0
  • Gender: Male
  • Azure knight
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #8 on: April 08, 2009, 01:05:48 PM »
if you can do this for the slim I would buy it in a heartbeat. 

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #9 on: April 08, 2009, 02:05:46 PM »
Okay, this product isn't for the slim, and as such it won't work on a slim.
I don't own a slim and do not plan to create a pcb for one person.

At the moment there only appears to be serious interest from two people, I thought more people would want an item like this! If there isn't any more interest from members of this community then it would probably be in my best interest to abandon this entirely.

Alien out

Sigs by Alien_X
www.ax-elec.com

Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #10 on: April 08, 2009, 02:08:47 PM »
if you can do this for the slim I would buy it in a heartbeat. 

Absolutely my exact thoughts as well.

Perhaps an alteration of the design to accompany the slim would be better, for the slim is more recent, and to my understanding, the pinout of the 3000 is also the same as 2000.

Many more people could try doing dual nub to the 2000 and 3000, which might actually make it more popular.

Not to mention, It does take time for good ideas to catch on.

Offline Tri-edge

  • I found Nemo!!
  • Around the block
  • *
  • Posts: 2381
  • Post quality +4/-0
  • Gender: Male
  • Azure knight
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #11 on: April 08, 2009, 05:03:23 PM »
Okay, this product isn't for the slim, and as such it won't work on a slim.
I don't own a slim and do not plan to create a pcb for one person.
I know it's not for the slim, I'm just saying if you make one for the slim that I would buy it (and a bunch of other people would too)


At the moment there only appears to be serious interest from two people, I thought more people would want an item like this! If there isn't any more interest from members of this community then it would probably be in my best interest to abandon this entirely.

Alien out
I would buy it if I still have my phat. If you release this I might go get a phat just to try this out

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #12 on: April 08, 2009, 07:01:02 PM »
I have a fat, but I would never mod it. However, if I did have a phat, I would definitely buy this to try an external controller. One for the slim would have more interest though :D

Sig by Kenshinffx - Thanks!

Offline GhoSt

  • Creating Null
  • Around the block
  • *
  • Posts: 2552
  • Post quality +19/-0
  • Gender: Male
  • Null Pointer Exception
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #13 on: April 08, 2009, 10:05:44 PM »
thats cool, got the altium files for it?
|Variegation - GhoSt's Final Controller|

|Nothing is deterministic.|

Offline MARIOPARTY53

  • I DONT FAIL
  • BANNED
  • E = MC² Mad Scientist
  • *
  • Posts: 1526
  • Post quality +0/-0
  • Gender: Male
  • Pc Gaming Rules
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #14 on: April 08, 2009, 10:44:25 PM »
dude, i sooooooooooooooooo need this, i will probaly buy one

thats really great  :hifive: i really hope this comes out
However today I was brutally raped by a door handle, and none of my friends helped me up off the floor after ten minutes, instead they all teabaged me, all 10 of them...

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #15 on: April 09, 2009, 12:16:59 AM »
thats cool, got the altium files for it?

Sorry, I designed this in eagle and it isn't open source.

dude, i sooooooooooooooooo need this, i will probaly buy one

thats really great  :hifive: i really hope this comes out

It's cool that you're interested, but with this amount of interest I doubt whether it will happen.

Sigs by Alien_X
www.ax-elec.com

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #16 on: April 09, 2009, 01:49:38 AM »
mate, i'll buy one if it's released. I also agree with the idea of making one for the slim, i think you would have more people interested with a 2000 version.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #17 on: April 09, 2009, 02:04:53 AM »
Okay, well with the current interest so far I don't think it will be possible to have sparkfun sell this item on my behalf. However I am going to put in an order with the PCB fab house for one (for myself to test out), if anyone would like to me to order a prototype for them along with mine then please PM me - the board will be $9.5 + postage (usually around 50p to almost any country). This will be just the bare PCB, so a connector will have to be soldered on by yourselves.

If anyone who owns a psp slim would like to work with me to develop a connector then I would happily oblige.
« Last Edit: April 09, 2009, 02:08:30 AM by Alien_X »

Sigs by Alien_X
www.ax-elec.com

Offline PhenomenalDesigns

  • Granny Spanker
  • *
  • Posts: 476
  • Post quality +0/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #18 on: April 09, 2009, 03:01:10 AM »
Would it be like a ribbon or an actual PCB?


Hoi! Pinoy ako!

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #19 on: April 09, 2009, 03:08:22 AM »
A fabbed pcb from same manufacturer as this -


Sigs by Alien_X
www.ax-elec.com

Offline atomicareprise

  • Registered BST
  • Acid Modder
  • *
  • Posts: 595
  • Post quality +2/-0
  • Gender: Male
  • FILIPINO SINCE BIRTH
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #20 on: April 09, 2009, 07:21:30 AM »
well you're doing  the d-pad why not do the abxy as well budy...

that will make it even...i'm also interested in this mod so i hope to see this product

sooner or later...doing external controller will now be much easier..
viperfan91 (phat), thaq93 (psp phat parts)
pinoyballa  (2 phats ), tri-edge (slim)
Awilliams357- to be shipped

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #21 on: April 09, 2009, 12:00:18 PM »
I would buy it if it was for slim.

Offline GhoSt

  • Creating Null
  • Around the block
  • *
  • Posts: 2552
  • Post quality +19/-0
  • Gender: Male
  • Null Pointer Exception
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #22 on: April 09, 2009, 03:46:19 PM »
well you're doing  the d-pad why not do the abxy as well budy...

that will make it even...i'm also interested in this mod so i hope to see this product

sooner or later...doing external controller will now be much easier..

because mos't people have the ability to solder to the Powerboard, and alot cannot solder wires to a 0.5mm pitch zif connector.
|Variegation - GhoSt's Final Controller|

|Nothing is deterministic.|

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #23 on: April 09, 2009, 05:18:57 PM »
Seriously you will need to make one for the slim with the D-pad and abxy. I asked jumbo and he wants me to pay him $30 just to do this. I'd rather pay $30 for this for d-pad and abxy then pay jumbo for something that with things can happen, like the wires could pop off in the mail and then what?
« Last Edit: April 09, 2009, 05:22:07 PM by EliteGamer83 »

Offline rceckspurt13

  • Acid Modder
  • *
  • Posts: 637
  • Post quality +2/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #24 on: April 09, 2009, 08:07:51 PM »
I'd say if it breaks in the mail, you send it back with a nice note explaining what happened and ask for it to be fixed. I'm sure you could get it re-done.
Any Questions? Please Contact Me: rceckspurt13@gmail.com

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #25 on: April 09, 2009, 08:11:24 PM »
I'd say if it breaks in the mail, you send it back with a nice note explaining what happened and ask for it to be fixed. I'm sure you could get it re-done.


I mean still even thatt, like if I acedently break it off during modding or sometmes in the future if jumbo leaves AM or whoever I get to do it. I'd much rater have something I can hold in my own hands and do myself.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #26 on: April 10, 2009, 01:23:45 AM »

I mean still even thatt, like if I acedently break it off during modding or sometmes in the future if jumbo leaves AM or whoever I get to do it. I'd much rater have something I can hold in my own hands and do myself.

You want to know the solution to that? - Learn to solder

There isn't going to be a slim version from me.

This project can now be considered abandoned. To everyone who mentioned "slim" in this topic, I personally hate you.

Good bye

Sigs by Alien_X
www.ax-elec.com

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #27 on: April 10, 2009, 02:24:15 AM »
You want to know the solution to that? - Learn to solder

There isn't going to be a slim version from me.

This project can now be considered abandoned. To everyone who mentioned "slim" in this topic, I personally hate you.

Good bye

Don't be like that Alien. You did ask us to post here if we were interested in this product. You were bound to get people asking for a similer version for the slim, what did you expect.

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #28 on: April 10, 2009, 04:19:18 AM »
I am just annoyed as I spent a long time designing this for others, not myself.

I have decided to take some pictures of my process for soldering the PSP 1000 ABXY, since that seems slightly more popular. They can be found Here along with pictures of "The perfect joint".

Sigs by Alien_X
www.ax-elec.com

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #29 on: April 10, 2009, 07:28:22 AM »
Oh so now it's MY fault? All I said it "You should make one for slim" what's wrong with that!? you asked for feedback! now your flaming me just because I said it would be nice for slim!? you have anger issues dude... seriously =|

Alright who gave me another -  :angry:

Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #30 on: April 10, 2009, 07:54:03 AM »
Dude, chill the :censored: down.

It wasn't just you who said it. Not to mention he did ask for feedback on the item itself, not suggestions for other things.

You're also the one who MUST voice your opinion on everything, and then complain the minute someone else opposes you or things don't go your way, you freakin spazz.

And Alien, don't get me wrong, but this is a really cool idea, it's just because of the lack of phat modders and the time you made this that it's receiving a lack of interest.
« Last Edit: April 10, 2009, 07:56:11 AM by DarkShot »

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #31 on: April 10, 2009, 08:02:41 AM »
Dude, chill the :censored: down.

It wasn't just you who said it. Not to mention he did ask for feedback on the item itself, not suggestions for other things.

You're also the one who MUST voice your opinion on everything, and then complain the minute someone else opposes you or things don't go your way, you freakin spazz.

And Alien, don't get me wrong, but this is a really cool idea, it's just because of the lack of phat modders and the time you made this that it's receiving a lack of interest.

I do not complain I hold my ground and defend myself, Well I am not allowed to voice my opinion? everyone else does.  complain would be like "why is he picking on me make him stop please guy make him stop". Nah I'm only spazz 3 days a week ;)

Yea there aren't as many phat modders anymore if you could somehow make a ribbon cable you could make one for the slim to silver under along with the original then lead that ribbon cable to the spot uner the memory card reader for the pinout board. 

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #32 on: April 10, 2009, 08:09:38 AM »
When did I ever mention that it was your fault? - Try CTRL + F 'ing the word "fault", turns out your most recent post is the first and only result.

I don't think that this topic ElitePhyschologist83 is the correct place to post your professionally formulated opinion of my mental health, even though it is correct, I'm sure.

Why do you even need a breakout board anyway - what happened to your "friend the PROFESSIONAL SOLDERER  who can solder really really tiny things" - (Yes that is an exact quote). Besides if this professional solderer (LOL)  cannot solder a wire which has fully bonded with the traces, then how on earth has he earnt such a prestigious title?

Besides, you "noobs" (Yes correct terminology for most of you apart from aphex, darkshot and ghost) have missed the main point of my second to last reply:

There isn't going to be a slim version from me.

Did you notice the suggestive end to my sentence - "from me", well you obviously didn't but look again. Don't worry I will wait until realization dawns upon your precious little head.

Now if you feel this is a flame then by all reasons report it, I stand by all my points in this thread, and it would be no great loss to myself If this post were deleted. I can also get a whole lot nastier.

Sigs by Alien_X
www.ax-elec.com

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #33 on: April 10, 2009, 09:02:28 AM »
When did I ever mention that it was your fault? - Try CTRL + F 'ing the word "fault", turns out your most recent post is the first and only result.

I don't think that this topic ElitePhyschologist83 is the correct place to post your professionally formulated opinion of my mental health, even though it is correct, I'm sure.

Why do you even need a breakout board anyway - what happened to your "friend the PROFESSIONAL SOLDERER  who can solder really really tiny things" - (Yes that is an exact quote). Besides if this professional solderer (LOL)  cannot solder a wire which has fully bonded with the traces, then how on earth has he earnt such a prestigious title?

Besides, you "noobs" (Yes correct terminology for most of you apart from aphex, darkshot and ghost) have missed the main point of my second to last reply:

Did you notice the suggestive end to my sentence - "from me", well you obviously didn't but look again. Don't worry I will wait until realization dawns upon your precious little head.

Now if you feel this is a flame then by all reasons report it, I stand by all my points in this thread, and it would be no great loss to myself If this post were deleted. I can also get a whole lot nastier.

I have herd you say that you are not going to make one for a slim but I was suggesting it would be NICE never said you were I UNSTERSATND that you won't make one. I would rather have something I could do myself though and not have done for me. Just because your like a crazy insane solderer doesn't mean everyone is, I never said I WAS I admit it. Just because you can solder a tiny ZIF connector doesn't give you the right to assume anyone else who can't isn't as good as you.

Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #34 on: April 10, 2009, 09:06:00 AM »
I have herd you say that you are not going to make one for a slim but I was suggesting it would be NICE never said you were I UNSTERSATND that you won't make one. I would rather have something I could do myself though and not have done for me. Just because your like a crazy insane solderer doesn't mean everyone is, I never said I WAS I admit it. Just because you can solder a tiny ZIF connector doesn't give you the right to assume anyone else who can't isn't as good as you.

Who said anything about someone being better than another?

Certainly not Alien, myself, or anyone else who posted here.

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #35 on: April 10, 2009, 09:12:30 AM »
Look I don't want to fight with you bro, let's just stop this argument here and just say all you guys are right okay? is everyone now happy and there are no hard feelings?

P.S. don't even try to say something like "aww you can't think of any good comeback so you are trying to act all innocent now" this is not the case I don't like fighting with you guys are cool and certainly better modders then me, I'll take me lessons from you and any tips you have and apply them to my future mods.

Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #36 on: April 10, 2009, 09:21:30 AM »
Some realization. 'Bout time.

Now that that's done, I got a question for you Alien: Approximately how thin would the PCB be before needing to be sanded down?

Offline Alien_X

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1010
  • Post quality +3/-0
  • Gender: Male
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #37 on: April 10, 2009, 09:57:08 AM »
In what sense darkshot?

The manufactured pcb would have been 1.5mm FR4, and would need to be sanded down to approx. 0.4mm (I don't have a caliper but my pcb sanded around this thin seems to plug in fine. The copper clad which I sanded (Otherwise referred to as PCB) started out at around ~0.9mm.


Sigs by Alien_X
www.ax-elec.com

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #38 on: April 10, 2009, 09:58:20 AM »
Also question for alien,

Are you going to make these yourself with like a circuit board kit? or are you going to have them made for you by a company who makes custom circuit boards then sell them?


Offline DarkShot

  • I approve your mom
  • Acid Modder
  • *
  • Posts: 781
  • Post quality +0/-0
  • Gender: Male
  • ÜBERRAPESKILLETS
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #39 on: April 10, 2009, 10:48:38 AM »
Oh I was just wondering.

And Elite, he said he wouldn't because of the lack of interest.

Offline EliteGamer83

  • Millennium Poster
  • *
  • Posts: 1233
  • Post quality +0/-0
  • Gender: Male
  • Trusted Seller! Slim Modder! Graphics Artist!
Re: New Product: PSP 1000 Dpad Breakout Board - No more soldering
« Reply #40 on: April 10, 2009, 12:19:40 PM »
Meh you could make like 5 and try and see how they sell on eBay.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal