« previous next »
Pages: [1]   Go Down

Author Topic: Lazy Mans Way to Cutting the UMD Ring  (Read 2576 times)

Offline larcerkev

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
Lazy Mans Way to Cutting the UMD Ring
« on: December 10, 2009, 04:39:45 PM »
Well I just did this in a reasonable amount of time and it seemed quite easy.  It wasn't perfect but it seems decent for the time taken.

All that you really need to do is use a soldering iron and poke holes around the ring after removing the metal part.

Edit:  I wouldn't be so sure that this is "great" for the soldering iron...

Heres a pic of what mine looked like after I had already poked the holes with my soldering iron.



Then continuing to finish the circle...



Then poke the center out and sand it down.



And last is to cut up the ring and sand that down a little.
Giving me this as a end result.



I did actually break a small part of my umd door removing it with a butter knife so I'd recommend being quite careful on that part.

And, what do you think of my job?
« Last Edit: December 10, 2009, 04:43:44 PM by larcerkev »
Logged

Offline Vlad

  • Ω Allumnist Ω
  • *
  • Posts: 136
  • Post quality +0/-0
  • Gender: Male
  • PSP 1001 and PSP 2001 5.00 m33-6
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #1 on: December 10, 2009, 04:51:55 PM »
Not bad. The soldering iron thing is a good idea.
Logged
┌∩┐(◣ _ ◢) ┌∩┐

Offline larcerkev

  • Guppy
  • *
  • Posts: 9
  • Post quality +0/-0
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #2 on: December 10, 2009, 05:16:34 PM »
And to add to this.  Another use of the soldering iron would be for attaching the transparent sheet on the inside.



It looks bad on the inside but who sees that part??

They see this:

Logged

Offline P3nnyw1se

  • Acid Modder
  • *
  • Posts: 862
  • Post quality +1/-0
  • Gender: Male
  • AcidMaG
    • Myspace
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #3 on: December 10, 2009, 05:35:21 PM »
Not bad at all, just wear a mask b/c of the burning plastic fumes, they can create problems down the line if exposed to too much.  Anyway, I first saw the picture and though you took a drill  to it, xD
Logged

Offline laxboy

  • i like airplanes
  • Acidmods Alumni
  • E = MC² Mad Scientist
  • *
  • Posts: 1627
  • Post quality +12/-0
  • Gender: Male
  • CTVFD 9/11 lost but never forgotten
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #4 on: December 10, 2009, 05:54:24 PM »
not a bad idea. Though this will mess up your tip i do like the idea very creative.
Logged

Offline W-Gaming5

  • Millennium Poster
  • *
  • Posts: 1129
  • Post quality +1/-0
  • Gender: Male
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #5 on: December 10, 2009, 11:23:23 PM »
 :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored: :censored:v
« Last Edit: July 29, 2012, 12:46:46 PM by W-Gaming5 »
Logged
:censored:

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #6 on: December 11, 2009, 04:41:12 AM »
not bad work, I personally believe in using the right tools for the job IE a hole saw, but thats just me, lol....like penny said if your going to do it like this, make sure you dont breath the fumes from the plastic which can be toxic.
Logged

Offline dedafmonteur

  • E = MC² Mad Scientist
  • *
  • Posts: 2049
  • Post quality +4/-0
  • Gender: Male
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #7 on: December 13, 2009, 03:48:03 AM »
matt, this also counts for the fumes of a soldering iron/hot glue/stripping wires with a torch (like i do..lol_ etc.

evrything is a bit toxic, it's ok to breathe it if you just dont do it whole day long.
Logged

Offline N.W.A4LIFE

  • Motor Mouth
  • *
  • Posts: 92
  • Post quality +1/-0
  • Gender: Male
  • Acidmods User
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #8 on: December 13, 2009, 03:47:24 PM »
This Is bad if you ask me. A dremal is much safer then this. You also Ruin a soldering iron tip.THe Right side of it looks lumpy. The fumes are bad to breath in. PLus, A dremal would do this way faster and a cleaner job in the end.
It looks ok, but I would throw it on my psp umd door. Sorry
Logged

Offline Blazinkaos

  • Technology Revolution
  • Art & Theme Team
  • E = MC² Mad Scientist
  • *
  • Posts: 2259
  • Post quality +12/-0
  • Gender: Male
  • Time Passes Will You
    • ROOKIE BUILDERS DISCORD
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #9 on: December 13, 2009, 04:31:46 PM »
Thats what i did when i made my first window until i got dremel. Actually yea it may cover the tip of the soldering iron but you can get off with sand paper i do it all the time but i got several soldering tips.
« Last Edit: December 13, 2009, 04:32:45 PM by Blazinkaos »
Logged

*Thanks Modders/Friends:Ghost_Death, gr8npwrfl, Blizzrad, Kenshinffx.
*Thanks 802Chives for the Art position!

Offline psp339

  • Millennium Poster
  • *
  • Posts: 1371
  • Post quality +0/-0
  • Gender: Male
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #10 on: December 16, 2009, 12:23:11 AM »
I did this with my soldering iron the first time too. I now have a dremel to do this.
Logged

Offline spurgurgle

  • Acidmods Alumni
  • Millennium Poster
  • *
  • Posts: 1121
  • Post quality +17/-1
  • Gender: Male
  • call me spurg
    • my blog
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #11 on: December 16, 2009, 03:56:56 AM »
surely this isnt really a lazymans way of cutting the door out.

it'll take longer to melt it our with a soldering iron and then sanding the rought cut down...

then it would to drill it out with a hole saw and sand the edge smooth.

just my veiw..???
Logged

Sigs made by Ken and blazin from the AM Art team cheers guys.....
Spurgurgle d.t com
"I'm kinda like a typo, not quite right, but most people still understand me"

Offline N.W.A4LIFE

  • Motor Mouth
  • *
  • Posts: 92
  • Post quality +1/-0
  • Gender: Male
  • Acidmods User
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #12 on: December 16, 2009, 07:00:39 PM »
Quote from: spurgurgle on December 16, 2009, 03:56:56 AM
surely this isnt really a lazymans way of cutting the door out.

it'll take longer to melt it our with a soldering iron and then sanding the rought cut down...

then it would to drill it out with a hole saw and sand the edge smooth.

just my veiw..???
I see it the same way. I agree
Logged

Offline ApheX

  • Club AM VIP
  • Millennium Poster
  • *
  • Posts: 1094
  • Post quality +1/-0
  • Gender: Male
  • PSP And PSP Slim Case/Hardware Modder
    • ApheX MoDs
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #13 on: December 17, 2009, 06:07:55 AM »
I also agree, It's a nice idea if you don't ahve a dremal, but you do run the risk of burning up the umd door too much, plus you end up with a messy solder tip.
Logged

Offline SmaRkieS

  • Fart Sniffer
  • *
  • Posts: 45
  • Post quality +0/-0
  • Gender: Male
  • Made in The Philippines
Re: Lazy Mans Way to Cutting the UMD Ring
« Reply #14 on: December 18, 2009, 04:58:35 AM »
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal