« previous next »
Pages: [1]   Go Down

Author Topic: USB pic Prgrammer  (Read 2300 times)

Offline manwinder

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 59
  • Post quality +1/-0
  • Gender: Male
  • Acidmods User
USB pic Prgrammer
« on: February 27, 2011, 08:37:14 AM »
i  bought a pic programmer off ebay, it has usb. I installed the drivers and i tried to program a pic12f683 with robbo jitter mod, and when i open the hex file it shows all of these #'s, when i erase the chip and program it, and verify, it completes with no errors, but when i read the chip all it shows are 0000. I have programmed pic12f629, and it got programmed properly except for eerom data, in it there are all 0000, the pictures of the hex code and software running are below, should i use a different pic
Logged

Offline Anonamous

  • The Unknown Identity
  • Granny Spanker
  • *
  • Posts: 472
  • Post quality +14/-1
  • Gender: Male
  • Electrical Engineering Student
Re: USB pic Prgrammer
« Reply #1 on: February 27, 2011, 09:01:43 AM »
When I read my pic12F683 after programming it it comes up with all 0000 also. Its supposed to do that. It should be fine. But since your using a pic12F629 I cant be 100% sure.
Logged

Offline crazy-modder

  • Research & Development
  • Acid Modder
  • *
  • Posts: 854
  • Post quality +34/-2
  • Gender: Male
Re: USB pic Prgrammer
« Reply #2 on: February 27, 2011, 09:04:12 AM »
That's because you guys have read protect enabled. Disable that if you want to see the hex that was written to the chip.
Logged

Offline manwinder

  • ♪♪♪ Tone deff ♪♪♪
  • *
  • Posts: 59
  • Post quality +1/-0
  • Gender: Male
  • Acidmods User
Re: USB pic Prgrammer
« Reply #3 on: February 27, 2011, 03:30:00 PM »
what is read protect enabled, is it under the fuse settings, if it is then what is the name of the setting, and i am using both pic12f629 and 12f683
Logged

Offline k0mpresd

  • Chief squatting Hard
  • *
  • Posts: 18
  • Post quality +0/-0
  • Acidmods User
Re: USB pic Prgrammer
« Reply #4 on: February 27, 2011, 03:38:08 PM »
should be under config bits.
Logged

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: USB pic Prgrammer
« Reply #5 on: February 27, 2011, 04:23:16 PM »
what are you doing to ask?
Logged

Offline staticvoid

  • Chief squatting Hard
  • *
  • Posts: 19
  • Post quality +0/-0
Re: USB pic Prgrammer
« Reply #6 on: February 27, 2011, 10:03:29 PM »
just did one yesterday if it says programmed successful its good to go.
Logged

Offline EasyE

  • Motor Mouth
  • *
  • Posts: 83
  • Post quality +2/-1
  • Gender: Male
  • Acidmods User
Re: USB pic Prgrammer
« Reply #7 on: April 30, 2011, 03:10:32 AM »
Manwinder turn off CP in the settings of winpic and see if that helps it worked for me
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal