« previous next »
Pages: [1]   Go Down

Author Topic: PS3 snes controller (W.I.P)  (Read 5017 times)

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
PS3 snes controller (W.I.P)
« on: July 23, 2011, 08:02:40 PM »
This will be the process of me building a ps3 controller into a Snes controller. i will be using the ps3 original controller, and the original snes controller board(i will remove the shift register).

one problem is that i will not add the analog sticks, nor the R3,R2,L3,L2. i figured out that if you take off the analog sicks (magnetic sensor type), the analog sicks do not know the center point. But i figured out that if you solder together both pins (signals) then it knows exactly were the center is so it will not go crazy. So if you guys are going to remove the analog sicks completely then try to use a 4 pin sick. Because if i had to use the traditional 3 pin pot, i would of had to mess with resistors.

the next problem is that i need to add the PS button. But i dont know exacly what to use, i was planing to use the original ps button from the ps3, or a ipod touch home button ( or perhaps a custom button). on the top side i will add the leds, and i will add a usb-mini to were the cord hope is at.







« Last Edit: July 31, 2011, 06:02:06 PM by geraldrubalcava »
Logged

Offline 1TONpete

  • Millennium Poster
  • *
  • Posts: 1224
  • Post quality +47/-2
  • Sony specialist
Re: PS3 snes controller (W.I.P)
« Reply #1 on: July 23, 2011, 08:09:35 PM »
I recommend using the left analog stick were the dpad was. A lot of the simpler ps3 games use this only instead of dpad, and all the emus can use the analog stick for dpad , so you will be able to get more use out of your controller.
Logged

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #2 on: July 23, 2011, 08:27:39 PM »
well i butchered the analog sticks already. so i dont think that its possible. lol, well this will prob be just for showing off lol. i will upload the pic were i have the brissel for the dremel attachment. This one is the biggest help, i was able to take the carbon off the traces were its suppose to connect with the daughter board. and its now 100% easier to solder to it :)

im not qiute sure how to add multiple photos with the 5mb limit here. So if you know how can you instruct me?(each photo is like 3.8 so i hit the limit with one photo)
« Last Edit: July 23, 2011, 08:28:46 PM by geraldrubalcava »
Logged

Offline 1TONpete

  • Millennium Poster
  • *
  • Posts: 1224
  • Post quality +47/-2
  • Sony specialist
Re: PS3 snes controller (W.I.P)
« Reply #3 on: July 23, 2011, 08:38:55 PM »
I host all my pics on a separate site and link them here. I use photobucket , but any image host will work.
Do you know about the resistors when using no daughterboard?
« Last Edit: July 23, 2011, 08:47:25 PM by denali31004 »
Logged

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #4 on: July 23, 2011, 08:47:30 PM »
yes i know. but ive bin searching and i haven't had a concrete answer onto the two resisters value. that makes scene, i guess i will have to make a account somewhere.. im trying to use photo shop right now to shrink.
Logged

Offline 1TONpete

  • Millennium Poster
  • *
  • Posts: 1224
  • Post quality +47/-2
  • Sony specialist
Re: PS3 snes controller (W.I.P)
« Reply #5 on: July 23, 2011, 08:52:16 PM »
6.8k to 10k  resistors. I use 10k because I have a bunch all ready.
Logged

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #6 on: July 23, 2011, 08:56:05 PM »
thanks alot! 10k i have alot of those! so u fount it to be stable right? well good. also do i need any dummy load between ... lests say  comm2 and triangle? or can it be a open contact?
Logged

Offline 1TONpete

  • Millennium Poster
  • *
  • Posts: 1224
  • Post quality +47/-2
  • Sony specialist
Re: PS3 snes controller (W.I.P)
« Reply #7 on: July 23, 2011, 08:58:12 PM »
This page has a ton of info on all ps3 controllers and gives complete details on daughterboard info.
http://forums.xbox-scene.com/index.php?showtopic=648322
but the resistors connect from VCC to com1 and vcc to com2
« Last Edit: July 23, 2011, 08:59:20 PM by denali31004 »
Logged

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #8 on: July 29, 2011, 11:56:41 AM »
thanks for the info. hum, here is what i had so far...
http://www.youtube.com/watch?v=3fEY4CpRdJs
Logged

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #9 on: July 31, 2011, 09:50:19 PM »
here is the current update i have to far of the competition.

http://www.youtube.com/watch?v=U7wE4mQJqdw
Logged

Offline 3D0kassiah

  • Moderator
  • Acid Modder
  • *
  • Posts: 809
  • Post quality +19/-2
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #10 on: July 31, 2011, 11:43:23 PM »
ill donate another ps3 controller board if u need it buddy  :tup:
just hit me up with a pm and keep up the good work might have to MAKE u build me one also
Logged
Tracey: f off Rodent
rodent:i would of flew it to bill gates and shoved it up his a$$

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #11 on: August 02, 2011, 08:48:41 AM »
sweet man! well yea sure,  here is another update


http://www.youtube.com/watch?v=lOGehnfo8YI
Logged

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: PS3 snes controller (W.I.P)
« Reply #12 on: August 02, 2011, 09:04:34 AM »
Nice job! cant wait to see when its all finished
Logged

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #13 on: August 02, 2011, 09:05:51 AM »
yea probably gonna be done by tonight! lol and im getting my stuff ready for the ps360 controller. so watch out! lol  :laughing:
Logged

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: PS3 snes controller (W.I.P)
« Reply #14 on: August 02, 2011, 09:11:42 AM »
That will be a good mod but I am  hoping to top all even though I am only using a 360 controller now .I dont have a PS3 system to test it on a PS3 so hopefully by the october mod off I can :) good luck make sure you get your pics up and posted in time
Logged

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #15 on: August 02, 2011, 09:16:25 AM »
lol im pretty sure you might top me off lol. well you can always test a ps3 controller in the computer. on macs you can even sync a ps3 controller same like a ps3 xD.

ohh wow! i forgot! lol thank you for reminding me! i will post it up today!
« Last Edit: August 02, 2011, 09:16:54 AM by geraldrubalcava »
Logged

Offline Rodent

  • XBOX,XBOX360,PS3,WII
  • Acidmods Alumni
  • Around the block
  • *
  • Posts: 2983
  • Post quality +75/-5
  • Gender: Male
  • MODDER, REPAIR, CUSTOM IDEAS.
Re: PS3 snes controller (W.I.P)
« Reply #16 on: August 02, 2011, 09:18:14 AM »
Do i need anytype of softwear for the PS3 to use on my  computer of will it reconize it with a usb cable? also I cant test the rapid fire though on computer unless i have the game right?
Logged

 Tracey: I cant believe Rodent of all people made my damn day
3D0: snacks cartoons and naps  lol sounds like rodents typcial day :rofl:
Rodent consoles mods

Offline geraldrubalcava

  • E = MC²
  • *
  • Posts: 351
  • Post quality +15/-3
  • Gender: Male
  • Acidmods User
Re: PS3 snes controller (W.I.P)
« Reply #17 on: August 02, 2011, 09:27:14 AM »
i actualy dont know if the ps3 RF will work on the computer. for ps yes you do need the driver so it works though usb. (no blueooth for windows)

here are the driver for pc http://www.gamefront.com/how-to-use-a-ps3-controller-on-a-pc/

reason is that the eeprom from a genuine ps3 has to connect to usb to get the mac address and therefore it pairs itself for wireless. on the mac, ther blueooth MAC address is shared tough the devices connected.

but whats funny is that for a mac, ps3 works out of the box, for windows the 360 controller works out of the box. lol
« Last Edit: August 02, 2011, 09:30:09 AM by geraldrubalcava »
Logged
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal