Author Topic: Need help with the ps3 BMU Rapidfire  (Read 2723 times)

Offline 3lite117

  • Chief squatting Hard
  • *
  • Posts: 19
  • Post quality +1/-0
  • Acidmods User
Need help with the ps3 BMU Rapidfire
« on: October 14, 2011, 03:32:04 PM »
It seems Ive got it all together, but im having a problem changing the modes I know that the led shuts off when in the modes and gives a flash between them, but when I go to change modes I just simply dosent unless I put my finger between the com pin and earth pin on the pic and then press the tac button, also it will work of I put my finger on the Tp18 and then press the tac at the same time, Very strange Ive rewired all solder points used new wire on all connections and still the same problem... Has any one else had this? Im sure I must be doing somthing wrong.. but Its annoying me and I want to get it sorted  :boxed:
Ive done loads of 360 installs, but am noob to the ps3 hopefully some one can shed some light on the situation  :beg:
« Last Edit: October 15, 2011, 06:32:46 AM by 3lite117 »

Offline rafaliyo86

  • Acid Modder
  • *
  • Posts: 569
  • Post quality +12/-1
  • Gender: Male
  • Acidmods User
Re: Need help with the ps3 BMU Rapidfire
« Reply #1 on: October 19, 2011, 11:56:39 PM »
I had the same problem. I try to do a bridge between leg 2 and 3. Someone (I dont remember who) told me here

Offline 3lite117

  • Chief squatting Hard
  • *
  • Posts: 19
  • Post quality +1/-0
  • Acidmods User
Re: Need help with the ps3 BMU Rapidfire
« Reply #2 on: October 20, 2011, 04:02:30 AM »
Did it work for you after that?

Offline hyper999

  • Acidmods Alumni
  • Millennium Poster
  • *
  • Posts: 1158
  • Post quality +544/-3
  • Research and Development
Re: Need help with the ps3 BMU Rapidfire
« Reply #3 on: October 20, 2011, 08:26:20 AM »
Seems to me that there is a problem with your connection between the PIC and the COM line

Offline rafaliyo86

  • Acid Modder
  • *
  • Posts: 569
  • Post quality +12/-1
  • Gender: Male
  • Acidmods User
Re: Need help with the ps3 BMU Rapidfire
« Reply #4 on: October 20, 2011, 10:42:43 AM »
Did it work for you after that?

yes, but it was with hyper´s code

Offline 3lite117

  • Chief squatting Hard
  • *
  • Posts: 19
  • Post quality +1/-0
  • Acidmods User
Re: Need help with the ps3 BMU Rapidfire
« Reply #5 on: October 21, 2011, 04:02:56 AM »
Seems to me that there is a problem with your connection between the PIC and the COM line


So what should I be looking for hyper? ive checked the tp solder point and its clean I made sure I didnt over cook the solder point im kinda runnung outa options  :help:

Offline hyper999

  • Acidmods Alumni
  • Millennium Poster
  • *
  • Posts: 1158
  • Post quality +544/-3
  • Research and Development
Re: Need help with the ps3 BMU Rapidfire
« Reply #6 on: October 22, 2011, 05:16:17 AM »
You have programmed your PIC wrong or wired it up wrong the code works fine on all current PS3 controllers.

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal