Author Topic: jtag help.. rrod (Read 4698 times)

snowcolt17 · « **on:** October 14, 2011, 08:53:48 PM »

so i jtaged a 360.. matt helped me through most of it. and Rodent. and Anonamous.. thanks guys

i added the molex connector to the bottom of the board to add a fan. when i put the mobo back in. started rrod..

first it was 0102.
replaced the xclamps. worked. for a little while started freezing..
throw another error. i was getting e79. i figured that was from the jtag wiring

i reflowed today. the 0102 went away and gave me e71. so i built a new freeboot.bin..

now its 0022

ive reflowed the hana, gpu, and cpu.. :/.

any suggestions?
[mod]Fixed name for Anonamous

[/mod]

Cookie Monster · « **Reply #1 on:** October 14, 2011, 08:59:39 PM »

reball?

snowcolt17 · « **Reply #2 on:** October 14, 2011, 09:06:09 PM »

thats what i was thinking.. i dont know anyone that does it for cheap. and i dont got the stuff

Cookie Monster · « **Reply #3 on:** October 14, 2011, 09:25:27 PM »

what does desoldering and taking off the molex do?

snowcolt17 · « **Reply #4 on:** October 14, 2011, 09:30:50 PM »

idk. i was thinking that might be problem. it started when i did that

Cookie Monster · « **Reply #5 on:** October 14, 2011, 09:43:26 PM »

i could be bending the board slightly and akwardly so the gpu isnt making good connections

Modded Matt · « **Reply #6 on:** October 15, 2011, 07:38:38 AM »

Quote from: shadowdawg101 on October 14, 2011, 09:25:27 PM

what does desoldering and taking off the molex do?

this....flash an old copy of xbr to it, its in crazys files

Anonamous · « **Reply #7 on:** October 15, 2011, 09:03:52 AM »

Check your jtag solder connections too, make sure they arent shorting anything on J2D2, J1D2 or J2B1 that wires do not go to for the hack. I think I recall seeing in the Xenon hardware sheet that some of them connect to the cpu and gpu n crap like that (obviously the SMC too hen the name the SMC hack)

Oh and BTW, you spelt my name wrong lol.

[mod]Fixed name for Anonamous

[/mod]

snowcolt17 · « **Reply #8 on:** October 15, 2011, 12:28:46 PM »

Quote from: snowcolt17 on October 14, 2011, 08:53:48 PM

so i jtaged a 360.. matt helped me through most of it. and Rodent. and Anonamous.. thanks guys

i added the molex connector to the bottom of the board to add a fan. when i put the mobo back in. started rrod..

first it was 0102.
replaced the xclamps. worked. for a little while started freezing..
throw another error. i was getting e79. i figured that was from the jtag wiring

i reflowed today. the 0102 went away and gave me e71. so i built a new freeboot.bin..

now its 0022

ive reflowed the hana, gpu, and cpu.. :/.

any suggestions?

Fixed name for Anonamous

i was in a hurry.. you didnt fix matts to Modded Matt. you need demoted lol.

thanks. and i will matt..

Rodent · « **Reply #9 on:** October 15, 2011, 01:07:41 PM »

We all know who matt is hes the

BOSS

snowcolt17 · « **Reply #10 on:** October 15, 2011, 01:31:05 PM »

i knew who i was talking about. lol..

but installed the old xbr for zephyr and it didnt boot.. now installing feeboot. hopefully something will work..

Cookie Monster · « **Reply #11 on:** October 15, 2011, 01:33:16 PM »

so is it definatly a software issue?

snowcolt17 · « **Reply #12 on:** October 15, 2011, 02:31:56 PM »

i reflashed and its working.. somewhat. it wont boot with a usb plugged in

snowcolt17 · « **Reply #13 on:** October 16, 2011, 04:16:35 PM »

ok so i did what matt said. and installed xbr. and it works.. if i boot with a usb plugged in. it will give me e71. unplug it and it works. if i boot with dvd drive hooked up. it gives me error 0022. unplug it and it works.. any ideas?

Modded Matt · « **Reply #14 on:** October 16, 2011, 04:25:41 PM »

make a new freeboot image and reflash it

Like I said It dosnt seem to be a problem with the xbox, but with the programming. this is all bootleg homebrew. It has issues.

put the original nand back on it and try it.

Anonamous · « **Reply #15 on:** October 16, 2011, 04:28:03 PM »

Quote from: modded matt on October 16, 2011, 04:25:41 PM

make a new freeboot image and reflash it

Like I said It dosnt seem to be a problem with the xbox, but with the programming. this is all bootleg homebrew. It has issues.

put the original nand back on it and try it.

i have never had rrod issues from a bad flash on a jtag. Only issues were hardware issues.

Modded Matt · « **Reply #16 on:** October 16, 2011, 04:41:12 PM »

about every third time mine boots it flashes rrod, usually a power cycle fixes it.

snowcolt17 · « **Reply #17 on:** October 16, 2011, 04:44:08 PM »

i will get the nand. and everything and do it on this computer. then use usb and flash back. i told rodent it was a bad flash.

i made a new freeboot image after i installed xbr.

Modded Matt · « **Reply #18 on:** October 22, 2011, 11:47:14 AM »

today i took my jtag apart so i could do install the protection jumper to protect the efuses from an official update. once done i put it all back together and turned it on only to get a rrod then a e79 error.

I turned the xbox off, and back on, then it hung on the load screen, but no errors. I reset the xbox one more time and loaded perfectly.

snowcolt17 · « **Reply #19 on:** October 22, 2011, 12:25:26 PM »

Quote from: modded matt on October 22, 2011, 11:47:14 AM

today i took my jtag apart so i could do install the protection jumper to protect the efuses from an official update. once done i put it all back together and turned it on only to get a rrod then a e79 error.

I turned the xbox off, and back on, then it hung on the load screen, but no errors. I reset the xbox one more time and loaded perfectly.

yea i saw somewhere where you could remove a resistor and bridge the point. might do it..
the aud_clamp wiring is supposed to keep it from e74..

after i installed xbr it doesnt rrod but..

if i have the dvd drive hooked up it will 0022. unplug it, it works. if i have a usb plugged in. e71. take it out. works.

thinking about starting all over. flashing the orginial nand. install xellous. then make the freeboot.

Modded Matt · « **Reply #20 on:** October 22, 2011, 04:23:22 PM »

sorry your having so much trouble man. I cant get dashlaunch to work properly, it keeps booting to the nxe instead of freestyle. I changed the path correctly and everything....but I can launch FSD from xex.

now i have been having issues with storage space for my arcade backups because they can only be launched from a MS hdd or MS formatted usb space. Well with freestyle dash it will load up the games from any file path. I use xex to copy the content from the official hdd to a folder of choosing on my usb hdd and then set the file path correctly in FSD. only problem is I cant move the 20 gigs from the official partition on my usb hdd except through official ms means. so the stuff on there I have to move back to the official hdd to convert the file over then move them over to the usb hdd from xexmenu again.

lol its about data management. I just kinda winged it when setting up my jtag storage. I wish I would have gone all the way to freestyle dash then started organizing data.

anyway good luck to you man

snowcolt17 · « **Reply #21 on:** October 22, 2011, 04:57:05 PM »

no jtag is perfect. found that out. lol i thought after the hardware stuff easy. nope wrong. lol. i ordered a 360 hdd case for mine. and going to put a 250gb in it.

ive got some isos i backed up. and i got to convert them to god. then back to iso. then back to iso and extract them and works perfect. idk why so much converting.

for the arcade. either get a transfer cable or ftp into the m$ harddrive and get the live games... took this off another site may help ya

Quote

For anyone else who wants to play XBLA from external USB drive.

You have to create a folder called Content in the root and within Content create a folder called 0000000000000000 (16 0's) so it looks like this USB:\Content\0000000000000000\ download XM360 then use xexmenu or freestyle dash to run the XM360.xex then you should see them and be able to unlock everything and to play them.

Rodent · « **Reply #22 on:** October 22, 2011, 06:15:17 PM »

all this jtag talk , and i havent even made one myself yet , guess thats going to have to happen now, you guys are just having way too much fun with your jtags

snowcolt17 · « **Reply #23 on:** October 22, 2011, 09:33:04 PM »

Quote from: Rodent on October 22, 2011, 06:15:17 PM

all this jtag talk , and i havent even made one myself yet , guess thats going to have to happen now, you guys are just having way too much fun with your jtags

hey im learning more and more about them :p. do it!

Rodent · « **Reply #24 on:** October 23, 2011, 03:04:11 AM »

Quote from: snowcolt17 on October 22, 2011, 09:33:04 PM

hey im learning more and more about them :p. do it!

Yes I know your learning, and you been doing great, and I will be making me a jtag when i get some free time.

snowcolt17 · « **Reply #25 on:** October 28, 2011, 03:16:20 AM »

so i was playing last night. and starts freezing. turn it on. 0022. i took it apart. and bolted it through the chassis. while i had it apart i added the molex and the fan molex thing. and soldered the sata cable to the bottom for a 3.5" hdd. now when it boots gives me 0102.. looks like i gotta reflow. but before i do i will unhook the sata and molex.. fml

heatgunned it. working. also didnt remove the molex cables or sata or hot glue on the bottom and its better tacked. :p. thanks though.

News:

Author Topic: jtag help.. rrod (Read 4698 times)