Author Topic: Reset Glitch Hack RGH (Read 103200 times)

Rodent · « **Reply #30 on:** November 17, 2014, 03:02:12 AM »

[smg id=2964]

here is where the C8 is on coolrunner and Thanks gizmo for matrix pic . that guy is very helpful Dgnex

rafaliyo86 · « **Reply #31 on:** November 17, 2014, 05:06:56 AM »

Thanks for the pic guys. The next chip i am goingo to test is squirt 2.0

Rodent · « **Reply #32 on:** November 17, 2014, 11:46:03 AM »

Quote from: rafaliyo86 on November 17, 2014, 05:06:56 AM

Thanks for the pic guys. The next chip i am goingo to test is squirt 2.0

It would be help full for this tutorial if you guys would show pics of diferent chips you use and video for boot times . to help other members out also . I think it would bring more members here for Jtagging and rghing questions

thank you all for your input

rafaliyo86 · « **Reply #33 on:** November 17, 2014, 11:58:12 AM »

Quote from: Rodent on November 17, 2014, 11:46:03 AM

It would be help full for this tutorial if you guys would show pics of diferent chips you use and video for boot times . to help other members out also . I think it would bring more members here for Jtagging and rghing questions

thank you all for your input

I will post some pics of the installation when I do it

Just a last question Rodent, do you program chips with matrix nand programmer? I have seen the pic you posted but I thought it was just to read/write nand, what program do you use to do it?

Rodent · « **Reply #34 on:** November 17, 2014, 01:50:12 PM »

Quote from: rafaliyo86 on November 17, 2014, 11:58:12 AM

I will post some pics of the installation when I do it

Just a last question Rodent, do you program chips with matrix nand programmer? I have seen the pic you posted but I thought it was just to read/write nand, what program do you use to do it?

you can use matrix nand programer to program the chips I use nand x i have 2 burned up nand x they will only work to program i think i burned them up when i was first learning to rgh and jtag and accedently turned the console on

trial and errors of rghing consoles also I learned alot from my mistakes

rafaliyo86 · « **Reply #35 on:** November 17, 2014, 02:41:26 PM »

I have also 2 nand x which can only program and a matrix nand programmer which was the firat nand reader I bought. Now I have a squirter

Rodent · « **Reply #36 on:** November 18, 2014, 04:37:21 AM »

[smg id=2953]

this is for hard wiring the R-jtag chip .

rafaliyo86 · « **Reply #37 on:** November 27, 2014, 05:12:47 AM »

well guys I installed Squirt 2.0 finally in a Falcon and it works perfectly. Boot times between 5-20 seconds. Here are some pics:

Rodent · « **Reply #38 on:** November 27, 2014, 05:57:04 AM »

Nice work! and thank you rafaliyo86 for sharing your Pics and info for the site greatly appreciated

Rodent · « **Reply #39 on:** December 07, 2014, 06:40:58 AM »

Plug Ins
Plug in #2 this one put in plug in 2 for xbox 360 neighboorhood
#2 XBDM
#3XRPC
#4RPC
#JRPC

I will update the other plug ins soon.

Rodent · « **Reply #40 on:** February 27, 2015, 07:28:53 AM »

Quote from: rafaliyo86 on November 27, 2014, 05:12:47 AM

well guys I installed Squirt 2.0 finally in a Falcon and it works perfectly. Boot times between 5-20 seconds. Here are some pics:

[spoiler]

[/spoiler]

I am using this chip on a rgh2 jasper 16mb

i know this is a falcon but what timing files do you recommend for Falcon and Jaspers?

rafaliyo86 · « **Reply #41 on:** February 27, 2015, 01:12:38 PM »

For the squirt 2.0 I used the timming called reloaded1 (autogg program)

Rodent · « **Reply #42 on:** February 28, 2015, 06:07:52 AM »

Quote from: rafaliyo86 on February 27, 2015, 01:12:38 PM

For the squirt 2.0 I used the timming called reloaded1 (autogg program)

thank you for the reply that is what i ended up using for a jasper. Reloaded rgh2 I believe in autogg

rafaliyo86 · « **Reply #43 on:** February 28, 2015, 06:34:11 AM »

Quote from: Rodent on February 28, 2015, 06:07:52 AM

thank you for the reply that is what i ended up using for a jasper. Reloaded rgh2 I believe in autogg

Welcome

Veut · « **Reply #44 on:** March 01, 2015, 01:28:42 AM »

@rafaliyo86 Pls I need help, I accidentally pulled the c7r112 pad for cpu reset. I did not hotglue the wire. I tried using R8C2 pad but after 5mins it doesnt seem to glitch to xell. The console is a falcon. Is there any other alternative cpu reset point?
Thank you.

Rodent · « **Reply #45 on:** March 01, 2015, 02:24:20 AM »

Quote from: Veut on March 01, 2015, 01:28:42 AM

@rafaliyo86 Pls I need help, I accidentally pulled the c7r112 pad for cpu reset. I did not hotglue the wire. I tried using R8C2 pad but after 5mins it doesnt seem to glitch to xell. The console is a falcon. Is there any other alternative cpu reset point?
Thank you.

Does the console boot?
what mod chip are you using?
is it rgh2 or are you trying to rjtag it?

Veut · « **Reply #46 on:** March 01, 2015, 02:57:21 AM »

The console boots on retail and I have written Xell. I am using squirt 2.0
It is RGH2

Rodent · « **Reply #47 on:** March 01, 2015, 09:18:20 AM »

Quote from: Veut on March 01, 2015, 02:57:21 AM

The console boots on retail and I have written Xell. I am using squirt 2.0
It is RGH2

you can use this point for the R8C2

Veut · « **Reply #48 on:** March 01, 2015, 11:49:38 AM »

Thank you very much I will try it and see how it goes.

Update:

Thank you very much for the help. It is now glitching.

Many thanks.
[mod]please Dont double post. Use your modify tab to update your post, thanks.[/mod]

nbaj · « **Reply #49 on:** June 25, 2015, 12:21:48 AM »

Quote from: Rodent on August 08, 2014, 06:33:55 AM

For RGH2 Jasper and RGH2 Falcon run the wires like this using Slim Blue Wire

Coolrunner REV C

Remove the C8 Cap
and bridge points 2 and 3
switching the coolrunner to slim after programming it works the best for boot times

Program the coolrunner for jasper RGH2 with timing file A
Program the coolrunner for Falcon RGH2 with timing file B

images shown here for wiring this is a jasper 512mb bb i do them all the same way
for all jaspers 16mb and 256mb and falcon 16mb rgh 2 14717 and up dashboards to previous 16756
(sorry for the dirty pics)

nand dumps make sure its on RGH2 not R-jtag

shown here part 1 first boot times

Part1
http://youtu.be/O44iVkyL5U8

shown here part 2 consistant boot times
Part 2
http://youtu.be/xyOMrzn-NAw

shown here part 3 fully assembled and great boot times still
Part 3
http://youtu.be/icvb1nlrIV4

Falcon RGH2 just as the same wiring as the jasper
Shown here Part 1
http://youtu.be/GrvdxvbhQhk

Shown here part 2 fully assembled now 16 second boot time
Part 2
http://youtu.be/jKaygxGKuRY

great tutorial

i noticed on the cr you have 2-3, and cap closed. jp and c8 removed. is this for both the jasper and falcon?
also to switch to slim after program, so i assume you program the cr with switch to phat. then when the switch is set to norm, you switch to slim?

thank you so much

Rodent · « **Reply #50 on:** June 25, 2015, 02:55:00 PM »

Quote from: nbaj on June 25, 2015, 12:21:48 AM

great tutorial

i noticed on the cr you have 2-3, and cap closed. jp and c8 removed. is this for both the jasper and falcon?
also to switch to slim after program, so i assume you program the cr with switch to phat. then when the switch is set to norm, you switch to slim?

thank you so much

the cap only needs to be closed for jasper as for falcons i also posted the set up for that the coolrunner was to show where the C8 cap was if you haven anymore question feel free to ask

program jasper with A and falcon with B timing files

Rodent · « **Reply #51 on:** July 17, 2015, 04:56:08 AM »

UPDATE! it has been out for some time now! I know some of our members already know about this but I need to get time to get us up to date with the new RGh1.2 method which is RGh2 but boots like rgh1 some timing files are changed etc

just to show you some proof of falcon and jaspers boot times also for xenon on later dashboards now can get the dvd key YEAH

Falcon
https://www.youtube.com/watch?v=PrPsOD5I9Zg&feature=youtu.be

Jasper
https://www.youtube.com/watch?v=O3-pTpj8lAc

Gizmo613 · « **Reply #52 on:** July 17, 2015, 03:27:16 PM »

just did a jasper last night and got instant boot all the time!!! Works wonder!

Rodent · « **Reply #53 on:** July 17, 2015, 03:56:00 PM »

Quote from: Gizmo613 on July 17, 2015, 03:27:16 PM

just did a jasper last night and got instant boot all the time!!! Works wonder!

yea i have done a few on falcons now and jaspers i want to try a xenon and zephyr ... i will hopefully have pics when i get time to post them

thematrix · « **Reply #54 on:** September 25, 2015, 01:30:57 AM »

Rodent - Can you confirm this diagram is correct?

I have never used matrix products but i ordered the programmer and v3 chips for rgh 1.2

Rodent · « **Reply #55 on:** September 25, 2015, 06:49:21 AM »

Quote from: thematrix on September 25, 2015, 01:30:57 AM

Rodent - Can you confirm this diagram is correct?

I have never used matrix products but i ordered the programmer and v3 chips for rgh 1.2

this is correct when i get a chance next time i use a a V3 or a ACev3 i will post pics showing that it can be done

thematrix · « **Reply #56 on:** September 27, 2015, 10:57:32 PM »

Quote from: Rodent on September 25, 2015, 06:49:21 AM

this is correct when i get a chance next time i use a a V3 or a ACev3 i will post pics showing that it can be done

great. i will try this since i have some rev c's laying around
i will wait for your v3 setup

i assume this programmer uses the same drivers as a nand-x, jrp v2?

thanks

Rodent · « **Reply #57 on:** September 29, 2015, 05:05:01 PM »

Quote from: thematrix on September 27, 2015, 10:57:32 PM

great. i will try this since i have some rev c's laying around
i will wait for your v3 setup

i assume this programmer uses the same drivers as a nand-x, jrp v2?

thanks

there are different drivers for each also i removed your pics you posted due to they weren't correct

thematrix · « **Reply #58 on:** September 30, 2015, 02:02:48 PM »

Quote from: Rodent on September 29, 2015, 05:05:01 PM

there are different drivers for each also i removed your pics you posted due to they weren't correct

Well damn

I'll wait for yours. I just found those elsewhere. I haven't tried the install on a v3 yet

Rodent · « **Reply #59 on:** September 30, 2015, 03:20:17 PM »

Quote from: thematrix on September 30, 2015, 02:02:48 PM

Well damn

I'll wait for yours. I just found those elsewhere. I haven't tried the install on a v3 yet

use the one i gave you in this tutorial if you need them for other ones like the ace chips google it for now i will try to upload pics later this week

News:

Author Topic: Reset Glitch Hack RGH (Read 103200 times)