Introductionin this guide i will be showing you how to install t0pfire into your xbox 360 controller
the code for t0pfire can be found here https://www.acidmods.com/forum/index.php/topic,34437 (https://www.acidmods.com/forum/index.php/topic,34437) all credit for the code goes to t0pP8uZz
Parts Needed- xbox 360 controller
- a pic 12f683 programmed with t0pfire
- 2x100 ohm resistors
- 1x10k resistor
- 2x1N4148 diodes (matrix only)
- 2x330ohm resistors (matrix only)
- 2xtactile buttons (push to make)
- some 30awg wire
Tools Needed- Solder iron
- Hot glue gun
- Wire cutters
- a 3mm drill (depending on tactile button size)
Difficulty rating: 3/5
Average Time to Complete: 30-45mins
Notes:Be carefull making sure you get the chip round the right way
and take care not to apply to much pressure when drilling the holes in your case
Step By Step Tutorial1- use this video by treemty to help you take your controller apart
Xbox 360 Wireless controller dissasembly video tutorial (http://www.youtube.com/watch?v=GOTg_XuuW8g#normal)
2- identify which controller type you have by using this guide by gameroms
https://www.acidmods.com/forum/index.php/topic,24699.0.html (https://www.acidmods.com/forum/index.php/topic,24699.0.html)
3-use these wiring diagrams to help along with your install
(https://www.acidmods.com/RAND/upload/files/upload/t0pfire__CG_diagram.jpg)
(https://www.acidmods.com/RAND/upload/files/upload/topfire___Matrix_diagram.jpg)
if you are confident installing t0pfire with only the diagrams there is no need to read on..
but if not heres a step by step guide for you.
extra buttons(https://www.acidmods.com/RAND/upload/files/upload/buttons1.JPG)
First take your to buttons bend the legs flat (be carefull not to snap them off) and solder about 3-4 inches of wire to 2 of the legs (make sure they are 2 on the same side) then twist the first 5-10 mm of wire together for strength
(https://www.acidmods.com/RAND/upload/files/upload/buttons2.JPG)
Now decide on your button placement and carefully drill 2 holes for them
glue the buttons in place and route 1 wire from each button to either side of the controller shell.
ok so thats the buttons installed. i will show you where to connect them later in this tutorial.
The chipfirst you'll need to program your chip with t0p fire find it here
(insert link to main thread)
(https://www.acidmods.com/RAND/upload/files/upload/chip1.JPG)
we will install the chip in the deadbug position as shown in the picture above
CG install(https://www.acidmods.com/RAND/upload/files/upload/cg1_0.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg2.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg3_0.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg4.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg5.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg6.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/cg7_0.JPG)
Matirx install(https://www.acidmods.com/RAND/upload/files/upload/matrix1.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix2.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix3.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix4.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix5.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix6.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix7.JPG)
(https://www.acidmods.com/RAND/upload/files/upload/matrix8.JPG)
ok so that is both install type's complete so test it, close it, and enjoy t0pfire.
here a vid to help you use it
t0pFire v2.0 Revision: 5 - BETA test demostration (http://www.youtube.com/watch?v=ev7LfvLnri8#normal)
FAQ/ Troubleshooting- As this is a new rapid fire code, i dont no of any problems if it is installed correctly, using this guide. how ever if you do have any problems feel free to ask questions