Acidmods

Console Modding------ ( Here you can talk about your favorite Consoles ) => Xbox One => Xbox One controllers/Xbox One Rapid fire Controllers => Topic started by: wwaaeell on November 20, 2020, 05:09:30 AM

Title: XB1 Controller Slim problem
Post by: wwaaeell on November 20, 2020, 05:09:30 AM: Hello

I changed the left analog to a new one and when I installed it the line indicated by the arrow was separated. Then I connected it to the hole in front of it .. and now the analog gives commands forward and backward only and does not give a command above or below

please help me (https://www.bing.com/images/blob?bcid=RGmzJv6UWA8CRQ)
Title: Re: XB1 Controller Slim problem
Post by: wickated on November 20, 2020, 09:49:11 AM: you did nothing wrong exept buying :censored: replacement thumbstick
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 20, 2020, 10:04:32 AM: ok why above or below Do not respond
Title: Re: XB1 Controller Slim problem
Post by: wickated on November 20, 2020, 02:27:19 PM: Quote from: wwaaeell on November 20, 2020, 10:04:32 AM
ok why above or below Do not respond
u mean left/right ? if so, solder wire from damaged thruhole to lowest hole of up/down stick.
Title: Re: XB1 Controller Slim problem
Post by: RDC on November 20, 2020, 02:28:01 PM: Jumper wire the spots with the Red dots together, then try it. If it still doesn't work, leave that jumper wire on there and then run another jumper wire from one of the Red spots to TP103.

(https://www.acidmods.com/RDC/XB1/Repair/blob.jpg)
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 21, 2020, 04:48:28 AM: thank you for reply mester RDC

When I connect a wire between the two points, the controller does not power up at all

(https://www.bing.com/images/blob?bcid=RDWFuEGM7hACLA)
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 21, 2020, 04:51:11 AM: Quote from: wickated on November 20, 2020, 02:27:19 PM
u mean left/right ? if so, solder wire from damaged thruhole to lowest hole of up/down stick.

i meane up and down not work
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 21, 2020, 04:59:07 AM: Quote from: wwaaeell on November 21, 2020, 04:48:28 AM
thank you for reply mester RDC

When I connect a wire between the two points, the controller does not power up at all

(https://www.bing.com/images/blob?bcid=RDWFuEGM7hACLA)

and are this the 103 you mentioned?

(https://www.bing.com/images/blob?bcid=RKQpgqSCvhACqxcxoNWLuD9SqbotqVTdPys)
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 21, 2020, 06:12:31 AM: Quote from: RDC on November 20, 2020, 02:28:01 PM
Jumper wire the spots with the Red dots together, then try it. If it still doesn't work, leave that jumper wire on there and then run another jumper wire from one of the Red spots to TP103.

(https://www.acidmods.com/RDC/XB1/Repair/blob.jpg)

still up and down, not working . i mean LSY

(https://www.bing.com/images/blob?bcid=RBy00F6ArxACeA)

(https://www.bing.com/images/blob?bcid=RMLJdh9N0RACcA)

(https://www.bing.com/images/blob?bcid=RDt0F02I0xACqxcxoNWLuD9SqbotqVTdP-Y)
Title: Re: XB1 Controller Slim problem
Post by: RDC on November 21, 2020, 07:36:35 AM: That wire is a bit on the large side, you should be using a 30awg Kynar wire. That wire will work, but take care or it will tear off that TP spot.

If LSY is stuck Down, then the ground connection there could open. Jumper the 2 Black spots together.

(https://www.acidmods.com/RDC/XB1/Repair/blob_2.jpg)

If LSY is stuck Up, then move on, you can do better and don't need the hassle, also means the 1.8v is not getting to it and that wiring should have restored that, or there is some other issue on there shorting the Wiper (center pin) to ground.

If the controller is not turning on after doing that, then first undo it and check again.
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 21, 2020, 08:56:12 AM: thanks for reply
LSY is not stuck up or down . it does not respond at all
analog responds back and forth
but it does not responds up or down
Title: Re: XB1 Controller Slim problem
Post by: RDC on November 21, 2020, 04:22:26 PM: Put a jumper wire from the center pin, the one between the Black and Red spots of the LSY POT, to TP63.
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 22, 2020, 04:10:05 AM: Quote from: RDC on November 21, 2020, 04:22:26 PM
Put a jumper wire from the center pin, the one between the Black and Red spots of the LSY POT, to TP63.

this is TP63

(https://www.bing.com/images/blob?bcid=RD-y6D2rtRECqxcxoNWLuD9SqbotqVTdP8U)
Title: Re: XB1 Controller Slim problem
Post by: wwaaeell on November 22, 2020, 05:16:06 AM: Quote from: wwaaeell on November 22, 2020, 04:10:05 AM

this is TP63

(https://www.bing.com/images/blob?bcid=RD-y6D2rtRECqxcxoNWLuD9SqbotqVTdP8U)

Thank you very much mester RDC you are a legend :clap:

The controller now works very well :tup: