« previous next »
Pages: [1]   Go Down

Author Topic: lm386 voltage output  (Read 1802 times)

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
lm386 voltage output
« on: December 07, 2008, 08:39:56 AM »
Hey how much voltage comes out of an lm386 when it's all wired up? What are the 2 resistors (191k ohm and 30k ohm) used for? To prevent too much voltage running through the lm386? Where's the voltage supply coming off of anyway, 5v point or the speakers? Sorry I'm such a noob, and if there's any additional info you think I could use, then it would be greatly appreciated. Thanks!
Logged

Sig by Kenshinffx - Thanks!

Offline 123sample

  • Registered BST
  • Who Farted ???
  • *
  • Posts: 231
  • Post quality +1/-0
Re: lm386 voltage output
« Reply #1 on: December 08, 2008, 01:58:44 AM »
https://www.acidmods.com/forum/index.php?topic=25303.0


Supply comes from 5v,

Point of speakers provides lower than 5v,

Therefore resistors needed to prevent burning led, Don't go below / above 191k 30k



Logged

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: lm386 voltage output
« Reply #2 on: December 08, 2008, 12:43:28 PM »
Okay thanks. So how much voltage comes out of the led output? That was my main question.
Logged

Sig by Kenshinffx - Thanks!

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: lm386 voltage output
« Reply #3 on: December 08, 2008, 02:08:13 PM »
Ill check for you in a second :D

Edit-
I get 3.3V in neutral state and i get 3.4V with music on at full blast. (Highest voltage written its 2.7V on average)
« Last Edit: December 08, 2008, 02:29:05 PM by Jumbo »
Logged

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: lm386 voltage output
« Reply #4 on: December 08, 2008, 05:56:49 PM »
Quote from: Jumbo on December 08, 2008, 02:08:13 PM
Ill check for you in a second :D

Edit-
I get 3.3V in neutral state and i get 3.4V with music on at full blast. (Highest voltage written its 2.7V on average)

what do you mean voltage written? But thanks for those values. I would assume it's similar for the soundboard mike sells. I'm gonne need some resistors for red LEDs, won't I...
Logged

Sig by Kenshinffx - Thanks!

Offline Jumbo

  • Dr. Mod
  • BST BAN
  • Around the block
  • *
  • Posts: 2399
  • Post quality +0/-3
Re: lm386 voltage output
« Reply #5 on: December 08, 2008, 07:01:35 PM »
Quote from: bustinthejustin on December 08, 2008, 05:56:49 PM
what do you mean voltage written? But thanks for those values. I would assume it's similar for the soundboard mike sells. I'm gonne need some resistors for red LEDs, won't I...
This is mikes board..

Ya by highest written the highest my multimeter with music was 3.4 volts. It was about 2.7-2.8 on average though.
Logged

Offline j.s2ghetto

  • Millennium Poster
  • *
  • Posts: 1001
  • Post quality +0/-0
  • Gender: Male
  • GHETTO inside
Re: lm386 voltage output
« Reply #6 on: December 08, 2008, 07:06:17 PM »
Quote from: bustinthejustin on December 08, 2008, 05:56:49 PM
what do you mean voltage written? But thanks for those values. I would assume it's similar for the soundboard mike sells. I'm gonne need some resistors for red LEDs, won't I...

it depends on ur red leds
http://cgi.ebay.com/50-PCS-0603-SMT-SMD-450-mcd-RED-LED-Free-Ship_W0QQitemZ220278241159QQcmdZViewItemQQptZBI_Electronic_Components?hash=item220278241159&_trksid=p3911.c0.m14&_trkparms=72%3A1205|66%3A2|65%3A12|39%3A1|240%3A1318

i have these and have no need for extra resistors
Logged

thank u P3nnywise for the sig
"See you have to understand the difference. The difference between me and you is to you, this is your job. To me, this is my life. The club; that's my job. The mall; that's my job. Your neighborhood; that's my job. This studio; this is my life. This is what I do better than anything."

Offline bustinthejustin

  • Registered BST
  • E = MC² Mad Scientist
  • *
  • Posts: 2326
  • Post quality +1/-0
  • Gender: Male
Re: lm386 voltage output
« Reply #7 on: December 08, 2008, 07:54:04 PM »
Thanks guys. Ghetto, thanks for the info. I need some more leds anyway and I was wondering which ebay seller I should get them from.
Logged

Sig by Kenshinffx - Thanks!
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal