« previous next »
Pages: [1]   Go Down

Author Topic: JDM-020: X point  (Read 5906 times)

Offline diegodiniz

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
JDM-020: X point
« on: September 14, 2015, 04:39:46 PM »
Guys, sorry my abd english cause im brazilian. I got this image from here. PCB Sacn of JDM-020:



Can you guys show me where is X point on the BOTTOM of PCB????
The main topic only show X and O points on the TOP of the PCB. But I miss the point on the BOTTOM of PCB JDM-020.
I know is ONE OF THIS 4 points on the RED CIRCLE...not sure wich is!



GUys, I think I "destroy" the vias trying to remove the glue from older solder.
If I sold on ANOTHER X POINT... it will work????

[mod]use the edit tab in the upper right, please don't double post![/mod]
« Last Edit: September 14, 2015, 06:23:44 PM by WHITE 4ND N3RDY »
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: JDM-020: X point
« Reply #1 on: September 14, 2015, 07:11:09 PM »
Most likely not. It all depends on how bad the damage is and where it is.


« Last Edit: June 26, 2017, 09:44:33 PM by RDC »
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline diegodiniz

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-020: X point
« Reply #2 on: September 14, 2015, 08:35:12 PM »
Thank you very much! I will try to solder on this point you show. But if itS NOT work...I will try on the TOP of PCB, next the BlackSquare.


I hope it works!
« Last Edit: September 15, 2015, 03:19:18 PM by diegodiniz »
Logged

Offline diegodiniz

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-020: X point
« Reply #3 on: September 15, 2015, 03:31:37 PM »
Quote from: RDC on September 14, 2015, 07:11:09 PM
Most likely not. It all depends on how bad the damage is and where it is.


RDC, the original X button is NOT working anymore, and I tried do Solder on the bottom and not works.
Should I try to solder on the TOP of PCB or is just waste of time???
I think I :censored:ed up my controller...X button dont work....

I will try to explain with this image.
The orange place is scratched and hard to see. If I try to solder on the RED paint, ALONG THE VIA...is it works???
like this:



[mod]you got to stop double posting. Use your modify tab! I've issued u a warning.[/mod]
« Last Edit: September 16, 2015, 03:30:03 PM by WHITE 4ND N3RDY »
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: JDM-020: X point
« Reply #4 on: September 29, 2015, 05:25:57 AM »
The only way that you are going to fix that now is to jumper the bottom spot that is still good to the top spot at the MCU.
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.

Offline diegodiniz

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: JDM-020: X point
« Reply #5 on: October 09, 2015, 03:11:51 PM »
RDC, can you teach me where is another O point???
The X is OK right now, but O point is messed up...
Please Help me.!
Thanks
Logged

Offline RDC

  • Administrator
  • Around the block
  • *
  • Posts: 2609
  • Post quality +90/-2
  • Gender: Male
  • The CGnome Project
Re: JDM-020: X point
« Reply #6 on: October 10, 2015, 05:29:22 AM »
If you have messed up the O spot that I have already shown, then that O buttons is pretty much gone for good, as there is no other spot. From there it goes into a middle layer an then to an inner BGA connection of the MCU, so you can not get to it at all. The only hope you would have would be that some of the via is still left and you could solder to that, but if you are messing up the vias, then that's not going to happen either.

Get yourself a newer controller that has the JDM-030 version board, and then the Simple Flex boards I designed for it, so you do not have to solder 1 thing onto the controller. ;)

https://www.acidmods.com/forum/index.php/topic,43753.0.html
« Last Edit: June 26, 2017, 09:45:22 PM by RDC »
Logged
Screwing up is one of the best learning tools, so long as the only thing you're not learning is how to screw up.
Pages: [1]   Go Up
« previous next »
 
SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal