Author Topic: Rapid Fire Method (No Chip)  (Read 380421 times)

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #480 on: January 26, 2009, 08:01:35 AM »
you can use either rumble and get the same effect.

and no this mod, however you chose to do it will only work with slightly depleted batteries, this is due to the led pulsing being too high with new batteries and the play and charge kit.

this mod reallly sucks, please think about using a 555 or a pic

Offline untamedcheetah

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #481 on: January 26, 2009, 11:05:37 AM »
I don't have much soldering experience, so I was trying to keep that to a minimum to avoid an epic fail that would short the whole board...

I have seen a 555 method, but "pic"?

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #482 on: January 26, 2009, 11:10:51 AM »
yea, "pic" or "microchip" same

programed
interuptable
circut


Offline untamedcheetah

  • Chief squatting Hard
  • *
  • Posts: 14
  • Post quality +0/-0
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #483 on: January 27, 2009, 05:01:19 PM »
Is this method supposed to disable the right trigger or did I burn something out unsoldering my mistake?

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #484 on: January 28, 2009, 04:48:54 AM »
you have a solder bridge between the top and center pin. or you have conected to the center pin

you have done something wrong, please post clear pictures of your solder joints

Offline xhris

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #485 on: February 01, 2009, 06:06:29 PM »
here



Question about this picture. How do you attach the wire to the middle point? Solder doesn't seem to work and hot glue don't seem to hold either. I lost my LED is the reason I am using the middle point now.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #486 on: February 02, 2009, 04:32:47 AM »
well, here goes, you already lost the led, so you cant do too much more dammage, LOL

take a normal steak knife, stick the point in the hole, dont push and dig in just stick it in there and spin it around, this will slightly peel back some of the green paint.

tin your wire and solder it to that hole.

hot glue will only hold a wire in place, it will not close the connection

Offline xhris

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #487 on: February 02, 2009, 08:22:57 AM »
HAHAHA no I can't do to much more damage. I guess next time I wont try and solder while on my pain pill.

I will try your suggestion above.

Thanks.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #488 on: February 02, 2009, 08:24:38 AM »
I believe if you read the label it will tell you something to that affect LOL

you could also do this using the rumble pack method.
cut the rumbe off its plug, wire the red wire to your switch, disregard the black, wire the other end of the switch to the center trigger pin
« Last Edit: February 02, 2009, 08:26:26 AM by modded matt »

Offline xhris

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #489 on: February 02, 2009, 08:29:49 AM »
LOL yeah it has it printed right on the side of the bottle. :)

I had that method done for a while but it wasn't ever reliable. Sometimes it would work good and sometimes it wouldn't. It might shoot 2 or 3 rounds then it might go crazy and shoot rapid fire. That is why I wanted to try this.

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #490 on: February 02, 2009, 10:30:28 AM »
I hate to be the one to tell you this, but you are going to get the same affect by doing it this ways aswell, you may get slightly better results, but it will still be unreliable and sparatic.

this is what you need to do, if you dont want to buy from the AM shop. go to radio shack and build this, you will be glad you did. this can be adjusted for many other games alsohttps://www.acidmods.com/forum/index.php?topic=25338.0

Offline DarkZero266

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #491 on: February 02, 2009, 03:51:39 PM »
lol i had the same problem of getting it to stick so i ripped out the led and used the positive end XD   

awesome tutorial btw. in cod4 my desert eagle shoots like an mp5 :laughing:

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #492 on: February 03, 2009, 05:58:59 AM »
come on dude, we are trying to better our controllers, not destroy them, if you tin the wire before going to the led this is actually very simple.

15 watt soldering iron. fine tip is prefured
clean sober stedy hands

if you dont have those two things dont even think about it

Offline tutata

  • Chief squatting Hard
  • *
  • Posts: 10
  • Post quality +0/-0
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #493 on: February 03, 2009, 09:54:46 AM »
come on dude, we are trying to better our controllers, not destroy them, if you tin the wire before going to the led this is actually very simple.

15 watt soldering iron. fine tip is prefured
clean sober stedy hands

if you dont have those two things dont even think about it
LOL nice responce.

Offline Ozzi56

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #494 on: February 04, 2009, 04:50:09 PM »
Hey, i did this mod for a fun, easy project and it worked out great!

Also: i demo'd it in COD5, and IMO, it works. My pistol shoots like a freicking machine gun.

It doesn't work in Halo thou :( i guess ill have to try a different mod for that.

Offline Cmoore

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #495 on: February 04, 2009, 09:31:20 PM »
I have done this mod and the controller works for the first clip, fires really fast (full clip in a second for the gewher in COD5), but the next clip fires a full clip in about 4 seconds. its really weird.  although it works for COD4.  Anyone know if there another way to do a rf for COD5 other than the pic or 555 way. thx

Offline wilson08

  • Ω Allumnist Ω
  • *
  • Posts: 121
  • Post quality +1/-0
Re: New Rapid Fire Method (No Chip)
« Reply #496 on: February 05, 2009, 02:12:10 AM »
I have done this mod and the controller works for the first clip, fires really fast (full clip in a second for the gewher in COD5), but the next clip fires a full clip in about 4 seconds. its really weird.  although it works for COD4.  Anyone know if there another way to do a rf for COD5 other than the pic or 555 way. thx
No, there isn't a way without a chip... CoD5 is patched so the rapid fire has to be timed, and below the limit.

Offline Blazinkaos

  • Technology Revolution
  • Art & Theme Team
  • E = MC² Mad Scientist
  • *
  • Posts: 2259
  • Post quality +12/-0
  • Gender: Male
  • Time Passes Will You
    • ROOKIE BUILDERS DISCORD
Re: New Rapid Fire Method (No Chip)
« Reply #497 on: February 05, 2009, 09:24:45 AM »
yea i prefer just going with the chip cuz if you dnt and use the cheapy way with just the wiring the led ground the middle pin of the trigger it work for about a month it actually wears and doesnt work after. happened couple times so chip is better and its not that hard to make.

*Thanks Modders/Friends:Ghost_Death, gr8npwrfl, Blizzrad, Kenshinffx.
*Thanks 802Chives for the Art position!

Offline Random11

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #498 on: February 07, 2009, 09:56:47 PM »
Hey, First time on this forum as a registered user. I did this mod with my old matrix 360 controller, i actually ruined two of the led's and the pad with corresponds with the two  :boxed: but not a biggy. I used the rumble idea modded matt had. was sufficient for my gaming needs. But now after i have reassembled my controller it constantly is disconnecting from my 360  :wacko: only when i hit a button. Not the "A" button, any in general.... Any ideas guys?

Offline wilson08

  • Ω Allumnist Ω
  • *
  • Posts: 121
  • Post quality +1/-0
Re: New Rapid Fire Method (No Chip)
« Reply #499 on: February 08, 2009, 03:28:17 AM »
Hey, First time on this forum as a registered user. I did this mod with my old matrix 360 controller, i actually ruined two of the led's and the pad with corresponds with the two  :boxed: but not a biggy. I used the rumble idea modded matt had. was sufficient for my gaming needs. But now after i have reassembled my controller it constantly is disconnecting from my 360  :wacko: only when i hit a button. Not the "A" button, any in general.... Any ideas guys?
Un-solder everything, then look to see if there is any solder splashes on the board!

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #500 on: February 08, 2009, 07:22:24 AM »
is it disconecting (sinc) or is it shutting down? (power)

either way wison is right, check for solder splashes

Offline Blazinkaos

  • Technology Revolution
  • Art & Theme Team
  • E = MC² Mad Scientist
  • *
  • Posts: 2259
  • Post quality +12/-0
  • Gender: Male
  • Time Passes Will You
    • ROOKIE BUILDERS DISCORD
Re: New Rapid Fire Method (No Chip)
« Reply #501 on: February 09, 2009, 08:42:23 AM »
yea something is touching something double check around the controller.

*Thanks Modders/Friends:Ghost_Death, gr8npwrfl, Blizzrad, Kenshinffx.
*Thanks 802Chives for the Art position!

Offline Random11

  • Guppy
  • *
  • Posts: 2
  • Post quality +0/-0
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #502 on: February 09, 2009, 09:25:56 PM »
hey yeah thanks guys, it was just the casing after reassembly was too tight on the reconnect button of the controller, so when it got any kind of electrical input or even the slightest budge it went off. DURRR lol my bad. I do however have another question. If anyone has the link to a AWSOME breadboard assembly tutorial for a nice rapid fire with a potentiometer i would greatly appreciate it. THANKSSS

Offline xboxerman

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #503 on: February 12, 2009, 10:25:02 AM »
hi guys this is my first login and post
first of all good forum u got goin here

and now my problem i have modded my xbox controller as shown in the beginning of this  tut. but i did not know there was a new and old type of controller ,  so guess what ... i have the newer cg version contr. and after modding my contr  the " rapid fire " button shoots like normal trigger :) 

my question is is there any any way to mod the newer cg contr. without the chip ?  coz  im in suriname and the parts are rare to find here , ( we dont have radio shack or what u call it )

i had to look for some days to find a push button  lol

i only play halo 3   so if there is a mod for the cg controller , i would really apreciate it if someone could help me out here :)

ps: srry for the long  maybe boring posts

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #504 on: February 12, 2009, 11:00:43 AM »
for the cg controller this must be done with a chip that you can buy here:https://acidmods.com/ShopUSA/ check with king mike to see if he will ship to you though.
« Last Edit: February 12, 2009, 11:03:45 AM by modded matt »

Offline xboxerman

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #505 on: February 12, 2009, 11:43:27 AM »
darn it
it's not possible for me to get that coz the costs go up to high eg. if i buy something in usa for $40 with all the fee's  it easy goes up to 90 bucks or more so that is why i was looking to make a simple mod  ,  what is the rumble pack mod??

Offline Modded Matt

  • Site Owner
  • Administrator
  • Around the block
  • *
  • Posts: 4649
  • Post quality +65/-3
  • Gender: Male
Re: New Rapid Fire Method (No Chip)
« Reply #506 on: February 13, 2009, 04:38:07 AM »
no! for a cg you MUST have a chip, of some kind. find an older matrix controller, or save some money. I am building a 555 timer to update the TUT this weekend I can post it to you when I am done? I dont need it, it is just for demonstration, so it will cost nothing but postage. if your intrested send me a pm, and I am not sure your country's customs will let it come through or not. thats your risk not mine. all contries are diferent. Ireland will let it come in, but wont deliver it in the post they must go and get it. but other countries will deliver it to your door, no questions asked LOL 

Offline xboxerman

  • Guppy
  • *
  • Posts: 3
  • Post quality +0/-0
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #507 on: February 14, 2009, 11:25:44 AM »
i do have a friend in miami who could maybe send it to me but i think he would be mad if he knew i wanted to mod my controller ( i usually play agains him online heheh:))

and how much do the matrix controllers cost??

i also have a wired controller that i tried to mod  ( where one wire goes to the ground pin of the rumble pack and the other to the midle  of the three pins ) bt it goes all strange works sometimes but usually just throws a grenade or something weird  LOL well i'll try to find a matrix controller this week if not ill ask my bud if he would be able to send to me k
thx

Offline chicoloco

  • Guppy
  • *
  • Posts: 1
  • Post quality +0/-0
  • Gender: Male
  • Acidmods User
Re: New Rapid Fire Method (No Chip)
« Reply #508 on: February 15, 2009, 02:24:08 PM »
can someone post a link or links to where i can get these items because i simply cant find them please help i am starting to give up :help:  :beg: :help: :beg:

Offline blackburn

  • Acid Modder
  • *
  • Posts: 915
  • Post quality +0/-0
  • Gender: Male
  • Xbox 360 Enthusiast and JTAGer
Re: New Rapid Fire Method (No Chip)
« Reply #509 on: February 15, 2009, 07:34:49 PM »
radioshack
mouser
frys (local here)

but please just buy a chip from the AcidMods store, this method is useless now days, and youll be supporting the website.....


All Sigs Made by ME!

 

SMF spam blocked by CleanTalk
SimplePortal 2.3.5 © 2008-2012, SimplePortal