Author Topic: PSP 1000 MOD LED WITH RARE FAIL (Read 9916 times)

rafaliyo86 · « **on:** January 01, 2011, 01:05:54 PM »

OK, guys today i have done a new mod on my psp with 4 orange leds and when i was doing a vid to show you

my psp turned off suddenly

. I turned it on again put the music again and happen the same.

The fail is rare because it look like turn off when the music is high.

Psp mod led fail

But if i pass this part of the track works fine and when the music ups againg it happen the same

Psp mod

What do you think?? Ever the same has happened to you?

frenulem - No.5417 · « **Reply #1 on:** January 01, 2011, 01:58:17 PM »

Never even

a PSP so take what i say with a pinch of salt, but sounds like a short

rafaliyo86 · « **Reply #2 on:** January 01, 2011, 02:06:36 PM »

This is what i think also but its rare that the psp has the problem only when the music is high. If it was a short it should fail always no??

frenulem - No.5417 · « **Reply #3 on:** January 01, 2011, 02:11:13 PM »

did you use a transistor?

rafaliyo86 · « **Reply #4 on:** January 01, 2011, 02:22:56 PM »

Quote from: frenulem on January 01, 2011, 02:11:13 PM

did you use a transistor?

No, only leds. I did another mod with 8 leds and withot transistor and i didnt have this problem

Famas · « **Reply #5 on:** January 02, 2011, 03:03:00 AM »

looks like too much power going to the leds when it goes high the psp shuts it self off to save itself ? could also be a short

rafaliyo86 · « **Reply #6 on:** January 02, 2011, 03:16:35 AM »

I would have to put a resistor??

frenulem - No.5417 · « **Reply #7 on:** January 02, 2011, 03:56:17 AM »

http://www.hebeiltd.com.cn/?p=zz.led.resistor.calculator

rafaliyo86 · « **Reply #8 on:** January 02, 2011, 06:34:44 AM »

I would need a 22 ohm resistor but i would like to know if someone has had the same problem to confirm 100%

Famas · « **Reply #9 on:** January 02, 2011, 06:58:33 AM »

btw you should always use a resistor to save your leds life in the long run i always use 1

so i think that would be a great start and also use a diode so power doesnt go back to the speakers ?

hyper999 · « **Reply #10 on:** January 02, 2011, 07:14:42 AM »

i do not think a diode is needed as an LED is a Light Emitting DIODE, but a resistor should be used even if it isnt the cause of the problem

Famas · « **Reply #11 on:** January 02, 2011, 07:18:15 AM »

it doesnt do the same thing a diode stop the current and voltage going back it make it go 1 way better safe than sorry ? maybe it does stop it going back though seen as it and led

hyper999 · « **Reply #12 on:** January 02, 2011, 07:53:57 AM »

yes an led does stop reverse current flow try it with your multimeter

@rafaliyo86 try it with a 22ohm resistor as you should have used one anyway, but you might just get lucky and fix the problem aswell

rafaliyo86 · « **Reply #13 on:** January 04, 2011, 12:22:24 PM »

ok i will try it, but i have another problem. yesterday a friend brouht me a psp wich didnt turn on, i did a bridge in the power fuse (like mine) and worked, but now when i press the analog stick or a place near it the psp gets freeze. i have tried with my psp wich has a bridge also and it happens the same. Here is a vid:

Psp fail

Famas · « **Reply #14 on:** January 04, 2011, 02:26:39 PM »

touching it down is shorting out the board

rafaliyo86 · « **Reply #15 on:** January 05, 2011, 12:05:39 AM »

this is what i thougth but sometimes gets freezes without press it. Its very confusing

With the orange led i have a update, i dont have put a resistor yet but if a plug the charger and the music is loud the psp doesnt turn off. Only turn it off when the volumen its at the maximum. if i under it just a little it doesn turn off

hyper999 · « **Reply #16 on:** January 05, 2011, 05:58:02 AM »

if the led problem is still bothering you id try a greater resistor
100ohm seems to be the magic number i use for everything so maybe try that

Famas · « **Reply #17 on:** January 05, 2011, 08:54:31 AM »

hyper not meaning to sound rude mate but the guy has a different problem read a couple post up if your bridging the fuse what was the rating of the fuse and use the same size resistor as the fuze ?

hyper999 · « **Reply #18 on:** January 05, 2011, 09:01:01 AM »

i know he has a problem except i have very little knowledge of psps so im offering help for the bit i know about, instead of just randomly guessing a solution for a problem and posting crap that wont help.

Famas · « **Reply #19 on:** January 05, 2011, 09:03:33 AM »

im not good with psp either just thinking if you bridge a fuse it renders the fuze useless so shouldnt you replace it with a resistor ?

frenulem - No.5417 · « **Reply #20 on:** January 05, 2011, 09:27:56 AM »

fuse and resistor are two different things, a fuse doesn't limit the current, just stops too much getting to the circuit by breaking. just sayin'

and it sounds like a bigger resistor is needed as hyper said, because if its fine all the way until it gets too loud, it must just overload the circuit

and for the nub, check for a cold solder, just re-solders the nubs points, that might work

Famas · « **Reply #21 on:** January 05, 2011, 02:11:58 PM »

never said they where but if the resistance goes over the resistance of the resistor it will blow out so same really but not at the same time

hyper999 · « **Reply #22 on:** January 05, 2011, 02:37:35 PM »

no they are not the same! a resistor should never be used in place of a fuse!

rafaliyo86 · « **Reply #23 on:** January 08, 2011, 09:20:08 AM »

Ok guys i have fixed the led problem. I put a 100 ohm resistor and worked but leds blind very slow, i changed it for a 22 ohm resistor and works also. Now i only have the rare problem when i press the analog stick or nearly it

Famas · « **Reply #24 on:** January 08, 2011, 12:23:12 PM »

no need to take the mick

Surge · « **Reply #25 on:** January 15, 2011, 07:37:30 PM »

I have had this problem before on a past mod. If you are using high intensity LED lights, they will tend to demand more power and over tax the power systen in the psp. the PSP has some kind of fail safe that shuts down when too much power is being drawn.
Sounds to me like a form of overheating prevention.

Gotta throw some resistors on there to tame those lights, It also never hurts to stash a toggle switch in there somewhere.

rafaliyo86 · « **Reply #26 on:** January 17, 2011, 01:55:27 AM »

Quote from: Surge on January 15, 2011, 07:37:30 PM

I have had this problem before on a past mod. If you are using high intensity LED lights, they will tend to demand more power and over tax the power systen in the psp. the PSP has some kind of fail safe that shuts down when too much power is being drawn.
Sounds to me like a form of overheating prevention.

Gotta throw some resistors on there to tame those lights, It also never hurts to stash a toggle switch in there somewhere.

yes, i fixed the leds problem with a 22ohm resistor, now i only have the problem when i press the analog stick or a place near it the psp gets freeze

K.A.O. · « **Reply #27 on:** January 17, 2011, 12:44:42 PM »

you prolly have a short in one of your wires rafa.

rafaliyo86 · « **Reply #28 on:** January 17, 2011, 12:50:47 PM »

do you mean a short in the mod cause the fail?? I have my friend´s psp with the same fail and it doesnt have led mod

I am desperated

I dont know what to do

hyper999 · « **Reply #29 on:** January 17, 2011, 12:53:26 PM »

i dont know jack about psps but, its unlikely that a power short would cause it to freeze, however; i was thinking perhaps it could be a short that is causing an unexpected input (such as the joystick being left and right at the same time, which is normally impossible) and causing the psp to freeze. I may not be right but i thought i'd just throw it out there as noone seems to have experienced this before...

News:

Author Topic: PSP 1000 MOD LED WITH RARE FAIL (Read 9916 times)