Author Topic: Drop Shot Mod ? (Read 29587 times)

tempermodz · « **on:** July 13, 2011, 11:26:15 PM »

Has anyone tried making a hex code for just drop shot for the xbox or ps3 ?
Just a drop shot code for the pic12f683, the normal pic, if I wrote it wrong.

Anonamous · « **Reply #1 on:** July 14, 2011, 09:28:43 AM »

Quote from: tempermodz on July 13, 2011, 11:26:15 PM

Has anyone tried making a hex code for just drop shot for the xbox or ps3 ?
Just a drop shot code for the pic12f683, the normal pic, if I wrote it wrong.

just wire up the b button to one leg of a tactile and the other to ground. You can also add the middle pin on the right trigger to that and put it on the same as the b button and it should hopefully work.

If not you could modify say the BMU3 opensource code and change the akimbo mode to a dropshot and set the rate to one and instead of wiring to the l trigger you could wire it up to the b button.

tempermodz · « **Reply #2 on:** July 15, 2011, 05:49:54 AM »

Noce, ima give it a try, thanks.. do you have diagrams showing witch points are for the b button on each controller?

hyper999 · « **Reply #3 on:** July 15, 2011, 09:08:59 AM »

Quote from: Anonamous on July 14, 2011, 09:28:43 AM

just wire up the b button to one leg of a tactile and the other to ground. You can also add the middle pin on the right trigger to that and put it on the same as the b button and it should hopefully work.

If not you could modify say the BMU3 opensource code and change the akimbo mode to a dropshot and set the rate to one and instead of wiring to the l trigger you could wire it up to the b button.

Sorry to burst your bubble but...

1. Won't work.

2. BMU3's akimbo code does not automatically press the L trigger when you press the R trigger, so this will not work either. However It wouldn't be too difficult to edit it to make it automatically press the L trigger.

Anonamous · « **Reply #4 on:** July 15, 2011, 09:15:59 AM »

Quote from: hyper999 on July 15, 2011, 09:08:59 AM

Sorry to burst your bubble but...

1. Won't work.

2. BMU3's akimbo code does not automatically press the L trigger when you press the R trigger, so this will not work either. However It wouldn't be too difficult to edit it to make it automatically press the L trigger.

I know, I was just giving some suggestions lol. And I now realize that the r trigger doesnt work when its grounded, if you ground the middle pin on the right trigger it does the same thing as the left trigger lol.

Nevbox · « **Reply #5 on:** July 15, 2011, 02:04:23 PM »

Anyone know how you make a quickscope button?

I have seen two options here, but the double pole switch is had to get and I don't know how to delay a something. Any one have any ideas

https://www.acidmods.com/forum/index.php/topic,39884.msg299430.html#msg299430

Also anyone know how to make it so you just press the tactile once and then it would drop you to the floor without holding it down?

tempermodz · « **Reply #6 on:** July 17, 2011, 09:14:23 AM »

So drop shot works with b and ground to the tactical button. Anyone know how could i install it on the ps3 controller ???

Also I pretty suck at coding, could anyone add drop shot to any of the open source codes ?

Nevbox · « **Reply #7 on:** July 18, 2011, 07:43:03 AM »

I am making one to join in with the topfire rapid fire mod and I should be coming out in the next month
also making a quickscope code

So you press the tactile and you shoot and B button at the same time

and about the ps3 guy look for the ps3 circuit diagrams and don't what ever you do try and scrap the button seen some idiot doing that on youtube.

smokes · « **Reply #8 on:** July 19, 2011, 08:56:42 AM »

Quote from: tempermodz on July 17, 2011, 09:14:23 AM

So drop shot works with b and ground to the tactical button. Anyone know how could i install it on the ps3 controller ???

Also I pretty suck at coding, could anyone add drop shot to any of the open source codes ?

For a PS3 this can be done by connecting TP1 and the TP point for the square button to a tactile button.

Nevbox · « **Reply #9 on:** July 19, 2011, 09:39:57 AM »

Button-Appropriate Resistor- tactile - power +

it's very basic

tempermodz · « **Reply #10 on:** July 20, 2011, 10:44:06 PM »

Alright awesome, ill be watching for that quickscope. I duplicated the R thumnstick
to a tactical and it sure improved my sniping kills. But looking foward for your code.

Like exactlu what resistor?

3D0kassiah · « **Reply #11 on:** July 25, 2011, 07:53:45 PM »

isnt that cheating?

FOOKz™ · « **Reply #12 on:** July 27, 2011, 10:45:17 AM »

some mods are cheating lol.

3D0kassiah · « **Reply #13 on:** July 27, 2011, 05:18:03 PM »

i uno guess its up in the air hate those ass clowns who drop shot makes me wanna invite them over for tea so i can hit them in the nuts after

lol

Nevbox · « **Reply #14 on:** July 28, 2011, 04:53:02 AM »

That didn't quite make sense but this is what the forum is about and the drop shot mode is coming out this week

3D0kassiah · « **Reply #15 on:** July 28, 2011, 03:26:26 PM »

why i said its up in the air discussion
drop shot can be done by mastering a button sequence are people getting that lazy?
didnt mean to offend anyone

Nevbox · « **Reply #16 on:** July 29, 2011, 03:48:07 AM »

It's kinda hard and it's slightly different as you can still aim

wittness · « **Reply #17 on:** August 02, 2011, 10:33:18 AM »

Does anyone have a drop shot & jitter ps3 mod / code?

Would be willing to pay for one!

Nevbox · « **Reply #18 on:** August 02, 2011, 03:01:37 PM »

Quote from: wittness on August 02, 2011, 10:33:18 AM

Does anyone have a drop shot & jitter ps3 mod / code?

Would be willing to pay for one!

Try the free code list

https://www.acidmods.com/forum/index.php/topic,37478.0.html

yasin · « **Reply #19 on:** August 06, 2011, 08:37:26 AM »

Quote from: Nevbox on July 28, 2011, 04:53:02 AM

That didn't quite make sense but this is what the forum is about and the drop shot mode is coming out this week

So, what about the promised drop shot mode?

Nevbox · « **Reply #20 on:** August 06, 2011, 09:01:39 AM »

Been kinda busy but I am working on it

yasin · « **Reply #21 on:** August 06, 2011, 01:31:43 PM »

Cewl.

Do we need a pic for this mod?

manwinder · « **Reply #22 on:** March 16, 2012, 10:19:09 PM »

nevbox could i see the code you have worked on for this, since i am trying to do it right now

nycxbox · « **Reply #23 on:** April 05, 2012, 04:06:00 PM »

Not sure if anyone cares. But this community has been good to me. SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

Rodent · « **Reply #24 on:** April 05, 2012, 04:47:09 PM »

Quote from: nycxbox on April 05, 2012, 04:06:00 PM

Not sure if anyone cares. But this community has been good to me. SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

Do you have a video showing thsi works? this is pretty cool if you made youself... congrates but would like to see some proof of how it works

Phantom · « **Reply #25 on:** April 05, 2012, 08:57:03 PM »

I just tried it on a cg2 board and it works, pull right trigger and you go into prone while your gun is firing rapidfire, when you release right trigger you automatically stand back up, the only weird thing ive found so far is that you need to wait a second when you turn the mod on, if you are to quick the controller disconnects when you press RT, other than that it is flawless. very nice work nycxbox

Rodent · « **Reply #26 on:** April 06, 2012, 05:52:39 AM »

Nice Work phantomz0.... good pic shows members how to install if they look closely

nycxbox · « **Reply #27 on:** April 06, 2012, 10:30:35 PM »

Yes, Most mods that are connected to PADs (ABXY PADS) have the tendency to extend the Sync push if you press sync to enable the mod and then press the RT right away - cause it also presses the B button pad - so the controller goes into sync mode. Best technique is to push the sync and release and say ONE to yourself (you only need to let it sit for less than .7 seconds) If you press sync and have the RT down (which again enables the B button too) or press it in less than 1 second after you pressed sync the controller will go into sync mode. Many mods with Drop shot, auto reload, jitter and such function like this. IF there is a trick to prevent this - I would love to know what it is -but I have yet to figure it out. I never had any issue with waiting less than 1 second after releasing SYNC before using a RF mode on a mod chip.

As for video proof. I don't think it is necessary - the install is super simple - the chips are reprogrammable, if you try it and don't like it you wasted 5 minutes of your life. If you tried it and like it - then I am glad you like my work. It is not set to the fastest rapid fire, but it should work on every COD game for must semi auto guns and the mode without rapid fire is great for you guys who use auto guns already.

ENJOY

Rodent · « **Reply #28 on:** April 07, 2012, 01:50:22 AM »

Quote from: nycxbox on April 06, 2012, 10:30:35 PM

Yes, Most mods that are connected to PADs (ABXY PADS) have the tendency to extend the Sync push if you press sync to enable the mod and then press the RT right away - cause it also presses the B button pad - so the controller goes into sync mode. Best technique is to push the sync and release and say ONE to yourself (you only need to let it sit for less than .7 seconds) If you press sync and have the RT down (which again enables the B button too) or press it in less than 1 second after you pressed sync the controller will go into sync mode. Many mods with Drop shot, auto reload, jitter and such function like this. IF there is a trick to prevent this - I would love to know what it is -but I have yet to figure it out. I never had any issue with waiting less than 1 second after releasing SYNC before using a RF mode on a mod chip.

As for video proof. I don't think it is necessary - the install is super simple - the chips are reprogrammable, if you try it and don't like it you wasted 5 minutes of your life. If you tried it and like it - then I am glad you like my work. It is not set to the fastest rapid fire, but it should work on every COD game for must semi auto guns and the mode without rapid fire is great for you guys who use auto guns already.

ENJOY

The only reason i asked for a video is so people could see a demonstration, of how it works... but thank you anyways for shareing your talent.

yasin · « **Reply #29 on:** April 07, 2012, 04:26:52 AM »

Installed this mod. It works fine.
How do you change modes?
Sync buttons turns the mod on/off.

I like the auto standing up feature.

Dropshot is nice, but not always needed.
It would be nice with one more mode: If LT is pressed then don't drop.

What do you think?

KingMike_OS · « **Reply #30 on:** April 07, 2012, 07:51:17 AM »

Its best to have drop Shot on a tact Butt so press it when needed

Or have Aim Disable So when Aim is Hold It will no Drop Shot

yasin · « **Reply #31 on:** April 07, 2012, 08:32:58 AM »

Yes i meant that. The aiming trigger LT.

Cancel dropshot when LT is pressed.

nycxbox · « **Reply #32 on:** April 07, 2012, 11:15:12 AM »

That is called Drop Shot with AIM DISABLE.. Many of the main mod makers do that. I personally don't think it is necessary, but everyone has their preference. I do not have an AIM disable code on my mod because I don't hook up the chip to the LT. The mod I shared with you guys here - it is very simple. If you want to disable drop shot you only need to press sync to turn it off. There are only 2 modes (With and Without Rapid fire) So LT aim disable is unnecessary here, but on a more comprehensive mod I can see the point.

If you want drop shot on a tact you don;t even need a mod. Let me give you guys a nice schematic that RDC shared with me on building Dropshot into any controller with a tact switch. I use this for my customer on hard coded mods that don't have a drop shot mode. What is great about this is it allows you to do a drop shot with the tact button when ever you want. IF you are using an automatic weapon, the gun will still fire as normal when you press the tact but it will drop. If you are using a semi auto weapon the tact will fire once and drop you but if you have ANY rapid fire mod enabled it will work with that mod and allow you to drop shot using rapid fire.

Here is a link to buy the 4066.

http://www.mouser.com/ProductDetail/Texas-Instruments/SN74LV4066AN/?qs=sGAEpiMZZMtxrAS98ir%252bs6Yg1tqWLu1bVp%2fTzCWw%2f6o%3d

Here is the Basic Diagram That RDC gave me.

Let me give you some hints on where to install it and how to install it.

On a Matrix - it will fit here. You will need to bend and cut the pins. I will see If I can find an install Diagram I did.

On a CG or CG install here.

This is a pretty simple mod just requires some patience when soldering. I have done of a ton of them they work great.

RDC was kind enough to design me an all in one board to manufacture - I never did. I might do it though soon an offer these as easy install kits. I wanted to use Micro 4066 with a quick solder board. Here are the prototypes RDC designed for me.

Rodent · « **Reply #33 on:** April 07, 2012, 11:38:51 AM »

Nice work and alot of info ..good pics

KingMike_OS · « **Reply #34 on:** April 07, 2012, 01:03:23 PM »

Thats Funny Was working on the similar thing same concept heheh nycxbox Beat me to it

Also have Addon Boards that can be added to any rapidfire on the market and Give you

Dropshot on Tact Switch Working independently or with Rapidfire or QuickKnife Digrams Below. Rodent have few simple to play with Soon

He will right Review About it.

DropShot can work With rapidfire speed so if you have rapidfire On the gun will drop shot with Rapidfire when Tact is press if the Rapidfire is Off

Than The Gun will fire normal Fire rate when the tact is Press and Drop Shot.

Digrams Below

lovey · « **Reply #35 on:** April 11, 2012, 09:15:24 AM »

love it thanks very much doing my sons now

Quote from: nycxbox on April 05, 2012, 04:06:00 PM

Not sure if anyone cares. But this community has been good to me. SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

tempermodz · « **Reply #36 on:** April 12, 2012, 09:50:56 PM »

I just tested this drop shot, Its pretty legit ! I tried on MW2 with the revolver/magnum. The rapid fire is ultra fast with it. It would of been a bonus if it had another mode with just rapid fire not the drop shot. Still pretty legit tho. I wonder If its possible installing to chips, this drop shot & lets say the 3 mode from acid mods, and use that one with the tactical to turn it on/off and the drop shot of course with the sync. Just have one off when using the other mod. But It would be kind of confusing when playing. Also if both are on, maybe the controller will go crazy or damage the chips. Ima see what i can do, and try it out.

Or perhaps using acids original to fire with the tactical button, or any other just firing the second chip with just the rapid fire with a tactical.. I just confused myself here but i'll make it happen

masterkush · « **Reply #37 on:** April 27, 2012, 04:55:40 AM »

hey guys, ive recently tried this code with TWO different curcuit boards and it does the same for both. it wont drop BUT if i remove my batterie pack it automatically drops ill post pics of my install later. ps does any 1 have the diagram for the matrix pcb?

nycxbox · « **Reply #38 on:** April 27, 2012, 09:58:55 AM »

Quote from: masterkush on April 27, 2012, 04:55:40 AM

hey guys, ive recently tried this code with TWO different curcuit boards and it does the same for both. it wont drop BUT if i remove my batterie pack it automatically drops ill post pics of my install later. ps does any 1 have the diagram for the matrix pcb?

THIS DOES NOT WORK ON MATRIX - ONLY CG.

You should use an optocoupler if possible for the install.

IF you are installing on a CG2 make sure you cycle back to off (as the mod will turn on once you put your batter pack in) so after you turn the controller on, cycle the mod back to off then start over should work fine.

Something wring with your install if this is not working for you on a CG or CG2

masterkush · « **Reply #39 on:** May 08, 2012, 01:06:34 PM »

Quote from: nycxbox on April 27, 2012, 09:58:55 AM

THIS DOES NOT WORK ON MATRIX - ONLY CG.

You should use an optocoupler if possible for the install.

IF you are installing on a CG2 make sure you cycle back to off (as the mod will turn on once you put your batter pack in) so after you turn the controller on, cycle the mod back to off then start over should work fine.

Something wring with your install if this is not working for you on a CG or CG2

im sorry to give you a hard time but refrase the second paragraph for me please

3D0kassiah · « **Reply #40 on:** May 13, 2012, 06:55:06 PM »

anyone have an install pic of this on a cg2?

Phantom · « **Reply #41 on:** May 13, 2012, 07:29:17 PM »

Look at my post in this thread, I installed it on a cg2. Just have to take the battery pack out to turn it off when the controller is off. https://www.acidmods.com/forum/index.php/topic,39929.msg313231.html#msg313231

3D0kassiah · « **Reply #42 on:** May 13, 2012, 07:45:18 PM »

Quote from: phantomz0 on May 13, 2012, 07:29:17 PM

Look at my post in this thread, I installed it on a cg2. Just have to take the battery pack out to turn it off when the controller is off. https://www.acidmods.com/forum/index.php/topic,39929.msg313231.html#msg313231

pic is blurry

Phantom · « **Reply #43 on:** May 15, 2012, 07:59:45 PM »

better?

Gizmo613 · « **Reply #44 on:** June 16, 2012, 08:20:55 AM »

Quote from: nycxbox on April 05, 2012, 04:06:00 PM

Not sure if anyone cares. But this community has been good to me. SO here is something you guys here wanted.

This is my Dropshot with auto get up hex. There should be Two modes with and without rapid fire.

12f683

Here you are.

http://www.mediafire.com/?coo1u0yseqs75on

Pin 1 Power
Pin 2 LED
Pin 4 SYNC
Pin 5 B Button
Pin 7 RT trigger
Pin 8 Ground.

Can anyone provide a schmetic to make this work for a matrix board. Only looking for the drop shot mod.

SethMods · « **Reply #45 on:** June 16, 2012, 09:49:21 AM »

Theodor613,
There are two main reasons why this code will not work on a Matrix controller. The first is that the triggers operate backwards on a Matrix compared to a CG. So the mod would think that you were pulling the trigger when it was released and releasing the trigger when it was pulled. Second, the Matrix controllers you a "matrix" to connect all of the buttons. So trying to drive the "B" button like you would on a CG will make the controller register multiple button pushes from various buttons instead of just the "B".

If you want I can provide you with a hex file that will work on the Matrix, but at a minimum you would need to wire something like a 2N3906 transistor up to control the B button.

Gizmo613 · « **Reply #46 on:** June 16, 2012, 02:46:50 PM »

Hey that would be great! Would wiring this up be similar to the one in this post? And thanks for the info on the difference between the controller.

Famas · « **Reply #47 on:** November 08, 2012, 09:42:19 AM »

hi Ive installed this at work using the pic 12f683 datasheet and the pinouts given on a cg and I'm only getting one mode on or off when described i should have two how do i change modes ha ha :Tupi:

yasin · « **Reply #48 on:** November 20, 2012, 10:34:32 AM »

Can you explain how this 4066 mod works?

I assume button 1 and button 2 stands for B button and Right trigger.

If so, why do they have both 2 connections?

EDIT: nevermind, got it working.

News:

Author Topic: Drop Shot Mod ? (Read 29587 times)